Connectrix SANnav

Dette dokument fremhæver minimumversioner samt anbefalede og nyeste kodeversioner for Dell Technologies Enterprise- og Datacenterinfrastruktur-produkter. Vi evaluerer og overvåger omhyggeligt kodeimplementeringsdata for at sikre, at produktudgivelser lever op til vores strenge forventninger om at give vores kunder pålidelige produkter og løsninger.

Denne KB indeholder trin til at udskifte zonemedlemmet.

Kan ikke importere MAPS-politik ved hjælp af BNA på SAN-switch.

Sådan gendannes en slot fra en EM-1045, KABINET, ADVARSEL, Slot XX bliver slukket (ikke nok strøm) meddelelse?

How to upgrade Rocky Linux v8.6 or above.

Hvilke porte skal være åbne for DR (Disaster Recovery) i SANnav 2.3.x og 2.4.x?

Connectrix SANnav: Error "IP Address is not reachable" while setting up disaster recovery on the Primary node.

How to add an NTP server after SANnav installation. Add the NTP servers to the chrony.conf file. Once added, restart chronyd and confirm synchronization using the "chronyc sources" command.

Proxy service does not start after replacing the SSL certificate with CA signed.

The switch user does not have privilege to access all possible VFs.

vCenter Host discovery on SANnav fails with error "Conflict-Existing Host"

Unable to send CallHome from SANnav or Brocade switch after Secure Connect Gateway (SCG) upgrade to 5.26.00.18.

SANnav Management portal GUI access issues after fresh installation. This web browser is too old to run the Web Console (missing selector(:is(): where()) A modern browser is required for security, reliability, and performance.

Procedure til tilpasning af kabinettets navn.

Switchstatus er marginal, selv efter fornyelse af selvsigneret kafka-certifikat i SANnav

Denne artikel beskriver, hvordan du indsamler tekniske supportoplysninger fra SANnav.

After upgrading to Fabric OS (FOS) 9.1.1c, unable to run inline commands from UNIX or Linux server to the switch with the "fosexec" commands.

Users are unable to log in due to full file systems on SANnav versions 2.2.1, 2.2.2, 2.2.2.1, and 2.2.2a.

A slow blinking amber light showing internally from the switch model DS6620B-V2, not from the switch panel, is confirmed by Brocade to be the LED from the eUSB card (on the motherboard).

From the switch supportsave & SANnav data, it was figured out that the SNMP traps are not received from the switch to SANnav

Sådan bruges PuTTY til SSH-nøglebaseret godkendelse.

Denne KB indeholder trin til at omdøbe et zoneobjekt. Du kan bruge disse trin til alle zoneobjekttyper, herunder cfgs, zoner og aliasser.

Seccermgmt-certifikatet viser fejlen "Er et ukendt x509-format."

Connectrix B-Series FOS compatibility check with SMI-S Agents

How to retrieve or access MiB files using SANnav.

Konfigurationsoutput, der genereres automatisk med switchname-suffiks i stedet for det filnavn, der leveres af brugeren.

Når de aktive porte har udtømt den aktuelle POD-licenspulje, tildeles der ikke yderligere porte en licens. I sådanne tilfælde skal du manuelt flytte licenser fra ubrugte porte ved at frigive POD-tildelingen til en nyligt anvendt port og reservere den. FOS 9.x og derover

This issue is seen when the SSL certificates are applied to SANnav however, the browser shows an insecure connection although the SSL certificate is installed.

This issue is seen while the backed-up switch configuration has been loaded to the switch using the configdownload command.

AES256-SHA256 (0x3d) and AES128-SHA256 (0x3c) is blocked for TLS.