Do not turn off your computer or disconnect from the power source while updating the BIOS as this could harm your computer. During the update, your computer will restart and you may briefly see a black screen.
Before updating, please read the installation instructions and important information noted below.
Dell OptiPlex 9010 System BIOS
Restart required AUTO INSTALLED This file was automatically installed as part of a recent update. If you are experiencing any issues, you can manually download and reinstall.This package contains the Dell system BIOS update. BIOS is a firmware package that is embedded on a small memory chip on the system board. It controls the keyboard, monitor, disk drives, and other devices.
To view all drivers for your OptiPlex 9010, go to Drivers and downloads.
Recommended
Loading the latest available version of the driver...
This is the latest Dell validated version of this driver
This is not the latest Dell validated version of this driver
O9010A21.exe | 8.16 MBEnter the Service Tag of your device to check the compatibility of this download with your device.
This is a large file. Depending on your connection speed, it may take some time to download.
File Format:
CPG BIOS Executable for Windows/DOS
File Name:
O9010A21.exe
File Size:
8.16 MB
Format Description
This file format consists of a BIOS executable file. The Universal (Windows/MS DOS) format can be used to install from any Windows or MS DOS environment.
To ensure the integrity of your download, please verify the checksum value.
MD5:
815bdccd5d505468c257899326f5d201
SHA1:
6eca6e452e340c33e0d8019aaeeec75f9c17f452
SHA-256:
a96b8c74ca3f1ef86e018d08938f8ba4c26c08b731c6d047e5c1f038430630e7
Sign in to Windows as an admin to use automatic scan. If your're already signed in as an admin and seeing this message, please reboot.
Your system is managed by your IT admin and features might be limited.
Find more updates. Use SupportAssist to find all the latest driver updates for your device.
Fixes & Enhancements
Fixes
- Fixed the issue where the UEFI Network boot option is not displayed in BIOS.
- Fixed the connection issue with the Intel Active Management Technology (AMT).
- Fixed the connection issue with the USB webcam.
Enhancements
- Enhanced the support for the Dell Backup and Recovery feature in the BIOS boot menu.
Read More
- Fixed the issue where the UEFI Network boot option is not displayed in BIOS.
- Fixed the connection issue with the Intel Active Management Technology (AMT).
- Fixed the connection issue with the USB webcam.
Enhancements
- Enhanced the support for the Dell Backup and Recovery feature in the BIOS boot menu.
Version
A21, A21
Release date
01 Oct 2015
Download Type
System BIOS
Category
BIOS
Importance
RecommendedDell Technologies recommends applying this update during your next scheduled update cycle. The update contains changes to maintain overall system health. It ensures that the system software remains current and compatible with other system modules (firmware, BIOS, drivers, and software) and may include other new features.
Important Information
Upgrading the Currently Released BIOS Images (Pre-Windows 8 released BIOS) and Windows 8 Feature Enhanced BIOS Images (Windows 8 released BIOS)
The new Windows 8 released BIOS contains new features and behavior, but the upgrade process for you is still unchanged.
Run the EXE application and the BIOS handles incorporating the new features and logic with your current settings.
After the upgrade, you will immediately see that one of the visible changes is the logo screen during boot. This change displays the logo at a larger size with no other information or text.
The new Windows 8 released BIOS contains new features and behavior, but the upgrade process for you is still unchanged.
Run the EXE application and the BIOS handles incorporating the new features and logic with your current settings.
After the upgrade, you will immediately see that one of the visible changes is the logo screen during boot. This change displays the logo at a larger size with no other information or text.
Supported Operating Systems
BIOS
Looking for a different OS? View the list of Dell supported operating systems
Applies to
Dell OptiPlex 9010
Installation instructions
Updating the BIOS from Windows
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Download and Installation
1. Click Download File.
2. Click Save to save the file to your hard drive.
3. Browse to the location where you downloaded the file.
4. Double-click the new file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS (Non-Windows users)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Installation
Note: You must provide a bootable USB drive. This executable file does not create the DOS system files.
1. Copy the downloaded file to a bootable USB drive.
2. Power on the system and then Press the F12 key.
3. Select USB Storage Device and boot to the DOS prompt.
4. Run the file by typing following command. For example:
C:\ OptiPlex_9010_X.Y.Z.exe
Where C is the drive letter of the USB device where the executable file is located and OptiPlex_9010_X.Y.Z.exe is the name of the downloaded file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS with UEFI boot mode enabled (Non-Windows users, Load Legacy Option Disabled)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Installation
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system and then go to BIOS Setup by pressing the F2 key.
3. Go to General > Boot Sequence > Boot > Boot List Option.
4. Change UEFI to Legacy of Boot List Option.
5. Go to Exit > Save Changes and reboot system.
6. Press F12 and then select USB Storage Device and boot to the DOS prompt.
7. Run the file by typing the file name.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, the system restarts again.
8. Go to BIOS Setup by pressing the F2 key and go to General > Boot Sequence > Boot > Boot List Option.
9. Change Legacy to UEFI Boot Option.
10. Go to Exit > Save Changes, and reboot the system.
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Download and Installation
1. Click Download File.
2. Click Save to save the file to your hard drive.
3. Browse to the location where you downloaded the file.
4. Double-click the new file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS (Non-Windows users)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Installation
Note: You must provide a bootable USB drive. This executable file does not create the DOS system files.
1. Copy the downloaded file to a bootable USB drive.
2. Power on the system and then Press the F12 key.
3. Select USB Storage Device and boot to the DOS prompt.
4. Run the file by typing following command. For example:
C:\ OptiPlex_9010_X.Y.Z.exe
Where C is the drive letter of the USB device where the executable file is located and OptiPlex_9010_X.Y.Z.exe is the name of the downloaded file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS with UEFI boot mode enabled (Non-Windows users, Load Legacy Option Disabled)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Installation
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system and then go to BIOS Setup by pressing the F2 key.
3. Go to General > Boot Sequence > Boot > Boot List Option.
4. Change UEFI to Legacy of Boot List Option.
5. Go to Exit > Save Changes and reboot system.
6. Press F12 and then select USB Storage Device and boot to the DOS prompt.
7. Run the file by typing the file name.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, the system restarts again.
8. Go to BIOS Setup by pressing the F2 key and go to General > Boot Sequence > Boot > Boot List Option.
9. Change Legacy to UEFI Boot Option.
10. Go to Exit > Save Changes, and reboot the system.
Need help with BIOS issues?
Find a solution in Dell's BIOS troubleshooting and usage guide.Drivers help and tutorials
For more downloads go to the Drivers and downloads.
For help on using the information on this page, please visit Driver Help and Tutorials.