System operacyjny Sonic | Nie można zsynchronizować NTP po skonfigurowaniu zarządzania IP VRF

Summary: System operacyjny Sonic | Nie można zsynchronizować NTP po skonfigurowaniu zarządzania IP VRF

This article applies to This article does not apply to This article is not tied to any specific product. Not all product versions are identified in this article.
Check out other resources

Symptoms

S5248F-3(config)# do show running-configuration | grep ntp
ntp server 3.3.3.1 minpoll 6 maxpoll 10 prefer true
ntp source-interface Vlan 30

S5248F-3(config)#
S5248F-3(config)# do show ntp associations
remote                      refid            st   t  when   poll   reach  delay  offset       jitter
------------------------------------------------------------------------------------------------------
*3.3.3.1                    202.112.31.197   3    u  13     64     1      0.497  -0.172       0.017
------------------------------------------------------------------------------------------------------
* master (synced), # master (unsynced), + selected, - candidate

S5248F-3(config)#
S5248F-3(config)# ip vrf mgmt
S5248F-3(config)#
S5248F-3(config)# do show ntp associations
remote                      refid            st   t  when   poll   reach  delay  offset       jitter
------------------------------------------------------------------------------------------------------
 3.3.3.1                    .INIT.           16   u  0      64     0      0.000  0.000        0.000　　　　★＝＝Here
------------------------------------------------------------------------------------------------------
* master (synced), # master (unsynced), + selected, - candidate
S5248F-3(config)#

Cause

NTP domyślnie używa zarządzania VRF; jeśli zarządzanie VRF nie jest skonfigurowane, NTP używa domyślnego VRF. 

Resolution

Należy przypisać odpowiedni VRF do NTP.

 

＊＊＊＊＊＊＊＊Default VRFs＊＊＊＊＊＊＊＊

S5248F-3(config)# ntp vrf default
S5248F-3(config)# do show ntp associations
remote                      refid            st   t  when   poll   reach  delay  offset       jitter
------------------------------------------------------------------------------------------------------
 3.3.3.1                    202.112.31.197   3    u  2      64     1      0.598  -0.139       0.000
------------------------------------------------------------------------------------------------------
* master (synced), # master (unsynced), + selected, - candidate
S5248F-3(config)#
＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊

Or 

＊＊＊＊＊＊＊＊other VRFs＊＊＊＊＊＊＊＊
S5248F-3(config)# do show running-configuration | grep ntp
ntp server 3.3.3.1 minpoll 6 maxpoll 10 prefer true
ntp source-interface Vlan 30
ntp vrf VrfTest

S5248F-3(config)# do show running-configuration vrf VrfTest
!
ip vrf VrfTest
!
interface Vlan30
ip vrf forwarding VrfTest
ip address 3.3.3.254/24
S5248F-3(config)# do show running-configuration interface Vlan 30
S5248F-3(config)# do show ntp associations
remote                      refid            st   t  when   poll   reach  delay  offset       jitter
------------------------------------------------------------------------------------------------------
*3.3.3.1                    202.112.31.197   3    u  16     128    377    0.556  0.336        0.166
------------------------------------------------------------------------------------------------------
* master (synced), # master (unsynced), + selected, - candidate
＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊＊

Additional Information

Nie dotyczy

Affected Products

PowerSwitch S4112F-ON/S4112T-ON, PowerSwitch S4128F-ON/S4128T-ON, PowerSwitch S4148F-ON/S4148T-ON/S4148FE-ON, PowerSwitch S5212F-ON, PowerSwitch S5224F-ON, PowerSwitch S5232F-ON

Products

PowerSwitch S5248F-ON, PowerSwitch S5296F-ON
Article Properties
Article Number: 000283267
Article Type: Solution
Last Modified: 21 Feb 2025
Version:  2
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.