SmartFabric OS10 VLT를 사용하는 스패닝 트리 프로토콜
Summary: VLT 지원 토폴로지는 VLT 도메인에서 루프가 없는 환경을 제공하지만, 일부 비 VLT 멤버 포트는 루프 시나리오로 끝날 수 있습니다. VLT의 스패닝 트리 프로토콜의 RSTP(Rapid Spanning Tree Protocol) 및 RPVST+(Rapid Per-VLAN Spanning Tree+) 모드가 지원되어 이 시나리오에 대한 솔루션을 제공합니다. 네트워크 토폴로지에 따라 VLT 도메인의 주 노드를 루트 브리지로 지정할 수 있습니다. ...
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Instructions
VLT 지원 토폴로지는 VLT 도메인에서 루프가 없는 환경을 제공하지만, 일부 비 VLT 멤버 포트는 루프 시나리오로 끝날 수 있습니다. VLT의 스패닝 트리 프로토콜의 RSTP(Rapid Spanning Tree Protocol) 및 RPVST+(Rapid Per-VLAN Spanning Tree+) 모드가 지원되어 이 시나리오에 대한 솔루션을 제공합니다. 네트워크 토폴로지에 따라 VLT 도메인의 주 노드를 루트 브리지로 지정할 수 있습니다.
참고: 네트워크에서 의도하지 않은 루프를 방지하려면 VLT를 활성화하기 전에 스패닝 트리(RSTP 또는 RPVST+)를 활성화하는 것이 좋습니다.
RPVST+는 Dell SmartFabric OS10에서 기본적으로 활성화되어 있습니다. 기본 스패닝 트리 모드를 변경하지 않는 한 RPVST+를 구성할 필요가 없습니다.
VLT-Peer1(config)# spanning-tree mode rapid-pvst
RSTP는 다음 명령을 사용하여 활성화됩니다.
VLT-Peer1(config)# spanning-tree mode rstp
VLT 노드의 MSTP(Multiple Spanning Tree Protocol)의 경우 네트워크 루프를 방지하도록 동일한 MST 영역에 두 VLT 피어 노드를 모두 구성합니다. VLAN-인스턴스 매핑, 영역 이름 및 개정 ID가 두 VLT 피어 노드에서 동일한지 확인합니다.
VLT-Peer1(config)# spanning-tree mode mst
VLT-Peer1(config)# spanning-tree mst configuration
VLT-Peer1(conf-mst)# instance 1 vlan 2-10
VLT-Peer1(conf-mst)# revision 10
VLT-Peer1(conf-mst)# name ExampleMSTregion
Affected Products
PowerFlex rack, ScaleIOArticle Properties
Article Number: 000317735
Article Type: How To
Last Modified: 06 May 2025
Version: 1
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.