- Notes, cautions, and warnings
- Dell PowerEdge T630 server overview
- Converting the system from tower mode to rack mode
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing system components
- Safety instructions for converting system from tower to rack
- Before working inside your system
- After working inside your system
- Recommended tools
- Front bezel (optional)
- System feet
- Caster wheels – optional
- System cover
- Inside the system
- Cooling shroud
- Cooling fans
- Cooling-fan assembly (optional)
- System memory
- Flex bays
- Hard drives
- Removing a hot swappable hard drive or solid state drive
- Installing a hot swappable hard drive
- Removing a 2.5-inch hard drive blank
- Installing a 2.5-inch hard drive blank
- Removing a 3.5-inch hard drive blank
- Installing a 3.5-inch hard drive blank
- Installing a 2.5-inch hard drive into a 3.5-inch hard drive adapter
- Removing a 2.5-inch hard drive from a 3.5-inch hard drive adapter
- Installing a 3.5-inch hard drive adapter into a hot swap hard drive carrier
- Removing a 3.5-inch hot swappable hard drive adapter from a 3.5-inch hot swappable hard drive carrier
- Removing a hard drive or a solid state drive from a hard drive carrier
- Installing a hot swappable hard drive into a hot swappable hard drive carrier
- Optical drives and tape drives
- Internal USB memory key (optional)
- Expansion card holder
- Expansion cards
- GPU card holder (optional)
- GPU cards (optional)
- Internal dual SD module (optional)
- Internal SD card
- Processors and heat sinks
- Power supply unit
- System battery
- Hard drive backplane
- SD vFlash card (optional)
- Control panel assembly
- System board
- Trusted Platform Module
- Power interposer board and power distribution board
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Troubleshooting system startup failure
- Troubleshooting external connections
- Troubleshooting the video subsystem
- Troubleshooting a USB device
- Troubleshooting a serial input and output device
- Troubleshooting a NIC
- Troubleshooting a wet system
- Troubleshooting a damaged system
- Troubleshooting the system battery
- Troubleshooting power supply units
- Troubleshooting cooling problems
- Troubleshooting cooling fans
- Troubleshooting system memory
- Troubleshooting an internal USB key
- Troubleshooting a micro SD card
- Troubleshooting an optical drive
- Troubleshooting a drive or SSD
- Troubleshooting a storage controller
- Troubleshooting expansion cards
- Troubleshooting processors
- Getting help
Καλώς ορίσατε
Ιστότοποι της Dell
Ιστότοποι της Dell
Καλώς ορίσατε στην Dell
Ο λογαριασμός μου
- Υποβάλετε παραγγελίες γρήγορα και εύκολα
- Δείτε τις παραγγελίες και παρακολουθήστε την κατάσταση αποστολής
- Δημιουργήστε μια λίστα με τα προϊόντα σας για να έχετε πρόσβαση σε αυτή
- Manage your Dell EMC sites, products, and product-level contacts using Company Administration.
Dell PowerEdge T630 Owner's Manual
Processors and heat sinks
Use the following procedures when:
- Removing and installing a heat sink
- Installing an additional processor
- Replacing a processor
NOTE: To ensure proper cooling, you must install a processor blank in any
empty processor socket.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\