Dell Chassis Management Controller Version 1.3 for PowerEdge FX2/FX2s RACADM Command Line Reference Guide

Description

Sets the CMC IP address. It displays an error message if the requested operation could not be performed, or a success message, if the operation is completed successfully.

To use this subcommand, you must have the Configure Chassis Administrator permission.

Synopsis

• racadm getniccfg
• racadm getniccfg –m <module>,

  where –m must be one of the following values:

  • chassis: default state if -m is not specified

  • server-n: where n = 1 to 4

  • switch-n: where n = 1 or 2

• racadm setniccfg -d
• racadm setniccfg -d6
• racadm setniccfg -s < IPv4Address> < netmask> < IPv4 gateway>
• racadm setniccfg -s6 < IPv6 Address> < IPv6 Prefix Length > <IPv6 Gateway>
• racadm setniccfg -o
• racadm setniccfg —p [-6}
• racadm setniccfg [-m <module>] —k [<speed> <duplex>]
• racadm setniccfg [-i <slot>] —v [<vlan_id> <vlan_priority>]

Input

• -d — Enables DHCP for the NIC (default is “DHCP disabled”.)
• -d6 — Enables AutoConfig for the NIC. It is enabled by default.
• -s — Enables static IP settings. The IPv4 address, netmask, and gateway can be specified. Otherwise, the existing static settings are used. < IPv4Address >, < netmask >, and < gateway > must be typed as dot-separated strings.

  racadm setniccfg -s 192.168.0.120 255.255.255.0 192.168.0.1

• -s6 — Enables static IPv6 settings. The IPv6 address, Prefix Length, and the IPv6 gateway can be specified.
• -o — Enable or disable NIC.
• -m<module> — Must be one of the following values:
  • chassis: Default state if - m is not specified.
  • server-n: where n=1–4
  • server-nx: where n=1–4; x=a-d (lower case)
  • switch-n: where n=1–2
• -i <slot> — Must be number n, where n=1 to 4
• -v — When performing on a switch, release and renew any DHCP lease on that port for the changes to be effective. The VLAN settings must be one of the following legal values:
  • no arguments imply remove vlan tag, not compatible with server-nx. For example (“server-4b”) notation
  • <vlan_id> 1 to 4000, 4021, and 4094 inclusive
  • vlan_priority> 0 to 7, inclusive
• -p — Disables IPV4 (default)/IPV6 protocol
• -k — Must be one of the following legal values:
  • no arguments implies autonegotiate
  • <speed> = 10, 100
  • <duplex> = half, full
• -r — Enable or disable redundant mode. The legal values are:
  • 1 — Enable
  • 0 — Disable

Example

• racadm setniccfg -s 192.168.0.120 255.255.255.0 192.168.0.1

• racadm setniccfg -d

• racadm setniccfg -d6

• Configuration of speed = 100Mbps and duplex= full duplex:

  racadm setniccfg -k 100 full

• Configuration of speed and duplex to autonegotiate:

  racadm setniccfig -k

• Configuration of redundant mode:

  racadm setniccfg -r 1

• Configuration of VLAN id and priority of a slot or all blades in a sleeve:

  racadm setniccfg -i 5 -v 1000 7

• Configuration of CMC to a static IPv6 address:

  racadm setniccfg -m chassis -s -6 2001:DB8::2 64 2001:DB8::1

• Configuration of server to use stateless autoconfiguration address:

  racadm setniccfg -m server-1 -d -6

• Configuration of VLAN id and priority for a switch:

  racadm setniccfg -m switch-1 -v 1000 7

• Removal of VLAN configuration from a switch:

  racadm setniccfg -m switch-1 -v