Configure OpenManage Enterprise by using Text User Interface
The Text User Interface (TUI) tool provides you a text interface to change the admin password, view appliance status and network configuration, configure networking parameters, and enable field service debug request.
NOTE: On the TUI interface, use the arrow keys or press
Tab to go to the next option on the TUI, and press
Shift + Tab to go back to the previous options. Press
Enter to select an option. The
Space bar switch the status of a check box.
Before logging into the TUI, accept EULA when prompted. In the next
Choose keyboard layout
screen, change the keyboard layout if needed.
On the
Change admin password screen, enter the new password and confirm the password.
NOTE: For the first time, you must change the password by using the TUI screen.
Use the arrow keys or press
Tab to select
Apply.
When prompted for confirmation, select
Yes, and then press
Enter.
Now you can configure OpenManage Enterprise by using the TUI. The TUI screen has the following options:
Change the Admin Password
Display Current Appliance Status shows the appliance service status.
Display Current Network Configuration shows the IP configuration details.
Choose Network Adapter menu lists all the available network adapters. Clicking on a network adapter will display its current settings.
Set Networking Parameters
Choose Network Adapter menu lists all the available networks adapters. Clicking on a network adapter allows you to reconfigure its network parameters and apply the changes to the appropriate interface.
NOTE:
By default, only IPv4 is enabled on primary network interface with a private static IP in the appliance. However, if a new network interface is added, both IPv4 and IPv6 are enabled for multihoming.
DNS configuration is only available on the primary network interface. If DNS resolution is desired on this interface, all host names must be resolvable by the DNS server configured on the primary interface.
Select Primary Network Interface allows you designate a primary network. Primary interface selection gives priority to the selected interface in terms of routing and is used as the default route. This interface will have the routing priority in the event of ambiguity. The primary interface is also expected to be the 'public facing' interface which allows for corporate network / internet connectivity. Different firewall rules are applied to the primary interface, which allow for tighter access control such as access restriction by IP range.
Configure Static Routes can be used if the networks require a static route to be configured to reach a specific subnet over the IPv4 and IPv6 networks.
NOTE: A maximum of 20 static routes per interface is supported.
Enable Field Service Debug (FSD) Mode
Reboot the Appliance
NOTE: Possibly after running a command to restart the services, it may be observed that the TUI displays the following message:
NMI watchdog: BUG: soft lockup - CPU#0 stuck for 36s! [java:14439].NMI watchdog: BUG: soft lockup - CPU#0 stuck for 36s! [java:14439]. This soft lockup issue likely occurs as a result of the hypervisor being overloaded. In such situations, it is recommended to have at least 16 GB of RAM and CPU of 8000 MHz reserved to the OpenManage Enterprise appliance. It is also recommended that the OpenManage Enterprise appliance be restarted when this message is displayed.
Setup Debug Logging
Enable Debug Logs
Disable Debug Logs
Enable SCP Retention
Disable SCP Retention
Services Restart
Restart All Services
Restart Networking
To confirm the current appliance administrator password, select
Change the Admin Password, and then enter the password. Press
Tab and select
Continue.
On the TUI screen:
To view appliance status and the IPv4 and IPv6 statuses and addresses, select
Current Appliance Status.
To configure network interface, select
Set Networking Parameters.
On the
Configure Network Interface screen, to enable IPv4, or IPv6, or both, press
Enter. Select
Apply.
NOTE:
Multihoming is enabled and the appliance can be accessed from two networks. It should be noted that the mandatory primary interface is used by the appliance for all external communication and when proxy settings are used.
To change the DNS Domain Name, ensure Dynamic DNS registration is enabled on the DNS server. Also, for appliance to be registered on the DNS server, select the
Nonsecure and secure option under Dynamic updates.
If the OpenManage Enterprise appliance fails to acquire a IPv6 address, check if the environment is configured for router advertisements to have the managed bit (M) turned on. Network Manager from current Linux distributions causes a link failure when this bit is on, but DHCPv6 is not available. Ensure that DHCPv6 is enabled on the network or disable the managed flag for router advertisements.
To perform any write operations on TUI, ensure that you type the admin password, and then configure IPv4 or IPv6.
To configure IPv6, ensure that it is already configured by a vCenter server.
In an IPv6 environment, when a Router Advertisement is configured for stateless configuration of multiple IPv6 IPs on a port, iDRAC supports a maximum of 16 IPs addresses. In such a case, OpenManage Enterprise displays only the last discovered IP and uses that IP as the out-of-band interface to iDRAC.
By default, the last discovered IP of a device is used by OpenManage Enterprise for performing all operations. To make any IP change effective, you must rediscover the device.
To collect the debug logs of the application, monitoring tasks, events, and task execution history, select
Setup Debug Logging
. In addition, to collect the template .XML files, select the
Enable SCP retention option under
Setup Debug Logging
. You can download the debug logs by clicking
Monitor > Audit Logs > Export > Export Console Logs in OpenManage Enterprise.
To restart OpenManage Enterprise, select
Reboot the Appliance.
Data is not available for the Topic
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\