- Notes, cautions, and warnings
- About your system
- Initial system configuration
- Before You Begin
- Initial Setup Sequence
- Initial CMC Network Configuration
- Logging In To The CMC Using The Web-Based Interface
- Adding And Managing CMC Users
- Configuring iDRAC Networking Using The Web-Based Interface
- Setting The First Boot Device For Servers
- Configuring And Managing Power
- Installing Or Updating The CMC Firmware
- Configuring The Optional iKVM Switch Module
- FlexAddress
- FlexAddress Plus
- Configuring The I/O Modules
- Network Information
- I/O Connectivity
- Port Auto-Disablement in Quad-Port Network Daughter Card (Dell PowerEdge M710HD Only)
- Mezzanine Cards
- I/O Module Port Mapping—Full-Height Blades
- I/O Module Port Mapping─Half-Height Blades
- I/O Modules—Switches
- Configuring A Switch Module Network Ethernet Port Using The Web-Based Interface
- Brocade M6505 16 Gbps FC SAN I/O Module
- Cisco Nexus B22 Fabric Extender Module
- Dell PowerEdge M I/O Aggregator Switch
- Dell Force10 MXL 10/40 GbE Switch
- Mellanox M4001F/M4001Q/M4001T Infiniband Switch I/O Module
- Dell PowerConnect KR 8024-k Switch
- Dell PowerConnect M8428-k 10 Gb Converged Network Switch
- Mellanox M2401G DDR Infiniband Switch I/O Module
- Mellanox M3601Q QDR Infiniband Switch I/O Module
- Cisco Catalyst Ethernet Switch I/O Modules
- Dell PowerConnect M6348 1 Gb Ethernet Switch I/O Module
- Dell PowerConnect M6220 Ethernet Switch I/O Module
- Dell PowerConnect M8024 10 Gb Ethernet Switch I/O Module
- Dell 8/4 Gbps FC SAN Module
- Brocade M5424 FC8 I/O Module
- I/O Modules—Pass-Through
- Installing Enclosure Components
- Troubleshooting The Enclosure
- Technical Specifications
- Getting help
Dell PowerEdge M1000e Enclosure Owner's Manual
Dell Force10 MXL 10/40 GbE Switch
The Force10
MXL 10/40 GbE switch module has two fixed 40 GbE ports on the base
module and provides support for two optional plug-in modules. This
module provides:
- Thirty two 1 GbE or 10 GbE internal ports — each port can operate in either 1 GbE or 10 GbE mode.
- Two native 40 GbE fixed ports on the base module for uplink connections. These ports can be used with 4 x 10G breakout cables to operate as 10 GbE uplink ports. The native 40 GbE ports can be configured as stacking ports.
- 10 GbE or 40 GbE external connectivity by using the following
plug-in modules in the two expansion slots:
- Four-port 10 GbE module using SFP+ optics (SR, LR, or LRM) or direct-attach cables (1 m, 3 m, 5 m DAC)
- Four-port 10GBASE-T module using RJ-45 connector (copper) cables
- Two-port 40 GbE QSFP+ module for 10 GbE SFP+ connections
For additional information about the Force10 MXL 10/40 GbE switch module, see the documentation that shipped with the module.
- expansion slots (8)
- LED status indicators
- USB storage port
- USB console port
- status/identification indicator
- power indicator
- 40 GbE QSFP+ ports (2)
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\