Deploying a drive on a system writes metadata to the drive that is not compatible between ME Series storage systems. For this reason,
ME5 Series storage systems do not support drives that have already been deployed either internally on an ME4 Series base system or on an expansion enclosure that has been used on an ME4 Series storage system. The reverse is also true: a drive that has been deployed on an
ME5 Series storage system (internally or on an expansion) cannot be used in an ME4 Series system.
| | | |
ME5 Series storage systems do not support controller upgrades from ME4 Series storage systems.
| | | |
Maximum number of host servers that a single storage system can connect to with one RAID controller module installed .
| 4
| 256
| 256
|
Maximum number of host servers that a single storage system can connect to with two RAID controller modules installed .
| 8 (4, if using high availability or redundancy)
| 256
| 256
|
Maximum number of SAS HBA cards that are supported in a single host server that is attached to single storage system. Dell recommends that you use two SAS HBA cards for all redundant cabling configurations.
| 2
| N/A
| N/A
|
Unused ports on a SAS HBA card already connected to an
ME5 Series SAS storage system cannot connect to another device (such as a tape drive or other model storage system).
| | N/A
| N/A
|
Maximum number
ME5 Series storage system to which a host server can connect.
| 2 (HA) with Dell 12 Gpbs
4 (HA) with HBA355e | 4
| 4
|
A hot spare for a disk group must be a drive of equal or greater size than any of the member disks.
| | | |
On Linux systems, Device Mapper multipath is required for multipath support.
| | | |
Coexistence of several Linux multipath drivers is not supported. For an
ME5 Series storage system with Linux host servers, only the Linux Device Mapper failover driver is supported.
| | | |
Virtual disks on
ME5 Series storage system cannot be used for booting.
| | | |
Disk Groups can be migrated between
ME5 Series storage systems by following the appropriate disk pool migration procedure.
| | | |
Maximum SSD cache size that is allowed is two SSDs. (You cannot use SSDs that have previously been deployed on an ME4 system.)
| | | |
All iSCSI host ports on a controller must have the same port speed.
| N/A
| | |
Maximum 12 Gbps SAS cable length that is supported is 4 m.
| | N/A
| N/A
|
iSCSI network rules:
- If the iSCSI initiators are connected to
ME5 Series storage systems through the network switches, ensure that your switches support IEEE 802.3x flow control, and the flow control is enabled for both sending and receiving on all switch ports and server NIC ports
- If you do not enable the flow control, your iSCSI storage may experience degradation of the I/O performance
- In addition to enabling the Ethernet IEEE 802.3x flow control, Dell recommends that you disable unicast broadcast storm control on the switch ports that are connected to the iSCSI initiators and target storage systems. Dell also recommends turning on the "PortFast" mode of the spanning tree protocol (STP) on the switch ports that are connected to the iSCSI initiators and target system
- Turning on the PortFast mode is different from turning off the whole operation of STP on the switch. With PortFast on, STP is still enabled on the switch ports. Turning off STP may affect the entire network and can leave the network vulnerable to physical topology loops.
| N/A
| | N/A
|
For optimal I/O performance, avoid having more than one iSCSI session originating from one host iSCSI port to the same controller. Ideally, the iSCSI host NIC must connect to only one iSCSI target port on the storage subsystem
| N/A
| | N/A
|
The FC can connect at either 16 Gbps or 32 Gbps, however 32 Gbps is recommended.
| N/A
| N/A
| |
The 10GBaseT iSCSI controller module can auto-negotiate to 1 Gbps.
| N/A
| (10 GBT) | N/A
|
Remote replication is not supported when the replication connection is directly connected. It must be in a switch topology
| N/A
| | |
Replication within iSCSI topology between
ME5 Series storage systems is supported regardless of connection speed. Replication between iSCSI and FC topology is not supported
| N/A
| | N/A
|
Replication within FC topology between
ME5 Series storage systems is supported regardless of connection speed. Replication between iSCSI and FC topology is not supported
| N/A
| N/A
| |
Online Drive firmware upgrade is not supported and might cause hosts to lose connectivity with the storage system
| | | |
When using drives that are 6 TB or larger, it is recommended to use either a RAID 6 Disk Group or an ADAPT Disk Pool. Due to the increased amount of time that is taken to reconstruct and copy-back, the chances for a second drive failure increases on either a RAID 1/10 or a RAID 5 Disk Group
| | | |
Data Assurance capable drives are supported in the storage system, however the Data Assurance feature is not available for these storage systems
| | | |
To create an NRAID, or RAID 0 disk group, you must use the CLI. For more information, see the
Dell PowerVault
ME5 Series Storage System CLI Guide.
| | | |
Disk groups and pools
| | | |
Minimum and maximum disks per virtual disk group:
- NRAID (non-RAID):1/1 (read cache only)
- RAID 0: 2/2 (read cache only)
- RAID 1: 2/2
- RAID 5: 3/16
- RAID 6: 4/16
- RAID 10: 4/16
- ADAPT: 12/128
| | | |
Minimum and maximum disks per linear disk group:
- NRAID (non-RAID):1/1
- RAID 0: 2/16
- RAID 1: 2/2
- RAID 5: 3/16
- RAID 6: 4/16
- RAID 10: 4/16
- ADAPT: 12/128
| | | |
Volumes, Initiators, hosts, and mapping:
| | | |
Supported module host-port configurations controller module:
| | | |
Virtual volume snapshots:
- Maximum snapshots per pool = 512
- Maximum base volumes per system = 1024
- Maximum base snapshots per volume
- 254 in the volume snapshot tree
- 8 in the volume snapshot tree
- Maximum mappable snapshots per system = 1024
NOTE:Active snapshots and replications use a substantial amount of the reserved space and undesired effects might occur if the reserved space is completely consumed. Use the CLI command
show snapshot-space to monitor space usage.
| | | |
Virtual volume replication:
- Maximum number of peer connections per system = 4
- Maximum number of replicated volumes per system = 32
- Maximum number of replicated sets for a volume = 1
- Maximum number of volumes for a replicated volume group = 16, if no other volumes belong to a replication set
- Minimum replication frequency that can be scheduled = 1
| N/A
| | |
Maximum SCSI reservations
- Per controller module = 1024
- Per LUN = 1
| | | |
Maximum SCSI registrations for virtual storage
- Per system: 32768
- Per LUN: 4096
| | | |
Maximum SCSI registrations for linear storage
- Per system: 32768
- Per FC LUN: 128
- Per iSCSI LUN: 85-128 depending on IQN length
- Per SAS LUN: 128
| | | |