Dell EMC Unity 600F

このドキュメントでは、デル・テクノロジーズのエンタープライズおよびデータセンター インフラストラクチャ製品向けの最小コード バージョン、推奨コード バージョン、および最新コード バージョンについて説明します。デル・テクノロジーズでは、コード導入データを慎重に評価および監視し、製品リリースが当社の厳しい要求を満たし、お客様に信頼性の高い製品とソリューションを提供できるようにしています。

Dell Storage Managerクライアントを使用してホスト サーバーのベスト プラクティス設定を自動的に設定する手順について説明します。

This KB describes one of the causes of the Unknown status of Replication.

This article describes one of the causes of the 0x1000100 error that results from the uemcli command.

Red Had Enterprise Linux client was unable to mount Unity NAS Server NFS Share. Receiving error NFS4ERR_MINOR_VERS_MISMATCH.

Some IDs such as Fake, nobody, c4, log, nogroup, admin, service, ECOM etc were found while scanning the Unity Array.

A system is either having its Management IP address configured during deployment or having the management IP address subnet changed. When a gateway is chosen, if the Subnet ID is used the Management IP configuration fails. This can occur either within Unisphere or at the command line. An error is seen about a failure to change the management IP configuration in Unisphere and also at the command line. Both Unisphere and the command line will be unable to be logged into. Access from ipmitool on either SP must be used to continue and resolve the issue.

Dell Unity: Users unable to access NDMP restored data due to local admin group SID changes between NDMP source and destination NAS servers.

This article describes an issue on the host side that lost some paths on HBA initiators during the code upgrade or after an SP reboot.

A dial home test message is sent via ConnectHome.

After an upgrade to 5.3, Support Assist with SCG (Gateway Server) can't be enabled.

Upgrading to Unity Operating Environment (OE) 5.3 causes SSH protocol to be disabled.

Adding NTP server fails with "Cannot create NTP servers. At least one of the specified NTP servers is not working (Error Code:0x6000840).

Unity SRM/SRA plugin discover shows the status as "Failover in progress".

Can ping across iSCSI IP addresses but cannot get the iSCSI initiators to work. iSCSI vs Replication interfaces.

If STIG and /user/account/settings are both enabled, following knowledge base article 22355 to reset the admin and service passwords, may not work for one of them (Dell correctable).

User or customer is unable to configure Integrated SRS or SCG (Previously Centralized Secure Remote Services) due to Error Code:0x6400b82

vCenter Server Appliance (VCSA) backup using VMware Appliance Management Interface (VAMI) did not complete after upgrading Unity to 5.1. This is due to a code issue in Unity 5.1 and later which rejects the mount request from vCenter when a slash "/" is appended to the mount path.

Unity may assign the same replication interface pair to every session when creating LUN replication sessions. The best way to ensure this does not happen is to manually create the replication sessions using UEMCLI. (User Correctable)

This article describes the process of how to rename an existing Block Storage resource using either Unisphere or UEMCLI.

This article discusses the limitations of SupportAssist in Unity OE version 5.3.

Unity Connect Home, or Dial Home email messages received by customer email accounts have the Unity Management IP address in the subject line. This is also seen in the body of the email alert in some scenarios. This is considered a security risk if the information is received or stolen during an information breach. This knowledgebase article describes the resolution.

報告された Nessus スキャンの脆弱性: 「Unix Operating System Unsupported Version Detection: SUSE Linux Enterprise 15.0のサポートは、2019年12月31日(通常のサポート終了)/2022年12月31日(LTSSオプション)に終了しました。Upgrade to SUSE Linux Enterprise 12.5 / 15.1.」

After upgrading code 5.2.1.0.5.013 or higher, Unisphere reports warning message regarding the spare drive policy.

This article details the susceptibility of Dell Unity products to the vulnerabilities detailed in CVE-2022-3437 and CVE-2022-3592.

This KB describes how to deal with the situation when Remote Syslog setting is not shown in the Unisphere UI.

MyService360サービス分析ダッシュボードでCloudIQ正常性スコアを［Install Base］ビューに統合する方法について説明します。これにより、MyService360とCloudIQポータルを使用するIT管理者によるサービスと製品の正常性管理が合理化されます。ポータルごとにサポート対象製品を確認し、CloudIQの役立つリソースにアクセスできます。

This KB describes the cause of error code 0x1000100 and its solution.

After a Unity array is upgrades to 5.2.x there is a chance "NTP server is partially unreachable" will start generating on the array.

この記事では、アレイの管理、設定、またはモニタリングのためにUnityアレイでUEMCLIの使用を開始する方法について説明します。