Removal
Front Bezel
Identify the front bezel highlighted in blue.
Unlock the front bezel with the key.
Press the release button and pull the left end of the front bezel.
Unhook the right end and remove the front bezel.
Front Top Cover
Identify the front top cover highlighted in blue.
Using a flathead or Phillips #2 screwdriver, rotate the lock counterclockwise.
Lift the latch until the front top cover slides back.
Hold the cover on both sides and lift it away from the system.
Rear Top cover
Identify the rear top cover highlighted in blue.
Lift the rear top cover from the system in the direction of the marked arrows.
Drive carrier
Select the drive carrier you want to replace.
Press the release button to open the release handle.
Holding the handle, slide the drive carrier out of the drive slot.
Drive Backplane
Identify the drive backplane highlighted in blue.
Disconnect the drive backplane cables from the backplane.
Press the blue release tabs to disengage the drive backplane from the hooks on the system.
Lift and pull the drive backplane out of the system.
Hard Drive Cage
Support Bracket
Identify the support bracket highlighted in blue.
Move the cables away from the support bracket.
Pull the plunger on either side of the installed support bracket to unlock it.
Lift the support bracket to remove it from the system.
Air Shroud
Identify the air shroud highlighted in blue.
Disconnect the cables from the power distribution board.
Unroute the cables from the air shroud.
Pinch and hold the air shroud from the middle and lift it from the system.
Cooling fan cage assembly
Identify the cooling fan cage assembly highlighted in blue.
Loosen the screw on the latch that secures the cables.
Open the latch that secures the cables.
Unroute the cables from the cooling fan cage.
Using a Phillips #2 screwdriver, loosen the screws to unlock the cooling fan cage assembly.
Lift the cooling fan cage assembly from the system.
GPU Fan Cage Assembly
Identify the GPU fan cage assembly highlighted in blue.
Loosen the screws that secure the GPU fan cage assembly.
Lift the GPU fan cage assembly from the system.
Expansion Card
Identify the expansion card highlighted in blue.
Rotate the PSBB retention latch upward to unlock.
Hold the expansion card by the edges and pull it out from the riser.
PCIe Switch Baseboard
Identify the PCIe switch baseboard highlighted in blue.
Remove the screws on the side of the chassis to release the GPU sled.
Loosen the thumb screws that secure the GPU sled latch.
Rotate the handle and slowly pull the GPU sled toward the rear of the system.
Remove guide panels on both the left and right side of the system.
Loosen the screw that secures the PCIe switch baseboard.
At a tilted angle, lift the PCIe switch baseboard out of the chassis.
Install
PCIe Switch Baseboard
Identify the PCIe switch baseboard location highlighted in blue.
At a tilted angle, insert the PCIe switch baseboard into the chassis.
Tighten the screw that secures the PCIe switch baseboard.
Install guide panels on both the left and right sides of the system.
Rotate the GPU sled latch inward to completely slide the GPU sled into the chassis.
Tighten the thumb screws that secure the GPU sled latch.
Install the screws on the side of the chassis to lock the GPU sled.
Expansion Card
Identify the expansion card location highlighted in blue.
Rotate the PSBB retention latch upward to unlock.
Hold the card by its edges and insert it into the connector until it locks in place.
Rotate the PSBB retention latch downward to lock.
GPU Fan Cage Assembly
Identify the GPU fan cage assembly location highlighted in blue.
Align it with the screw holes and place the GPU fan cage assembly into the system.
Tighten the screws that secure the GPU fan cage assembly.
Cooling fan cage assembly
Identify the cooling fan cage assembly location highlighted in blue.
Align it with the screw holes and place the cooling fan cage assembly onto the system.
Using a Phillips #2 screwdriver, tighten the screws to lock the cooling fan cage assembly.
Route the cables through the cooling fan cage.
Close the latch that secures the cables.
Tighten the screw on the latch that secures the cables.
Air Shroud
Identify the air shroud location highlighted in blue.
Pinch and hold the air shroud from the middle, and place it onto the system.
Route the cables through the air shroud.
Connect the cables to the power distribution board.
Support Bracket
Identify the support bracket location highlighted in blue.
Align the bracket’s guide slots with the system guides, then press until the plungers click into place.
Place the cables on the support bracket.
Hard Drive Cage
Drive Backplane
Identify the drive backplane location highlighted in blue.
Align and insert the backplane into the guides, then lower it until the blue release tabs click into place.
Connect the drive backplane cables to the backplane.
Drive carrier
Confirm the drive carrier you want to replace.
Press the release button on the front of the drive carrier to open the release handle.
Insert the drive carrier into the slot and slide until it connects with the backplane.
Close the drive carrier release handle to lock the drive in place.
Rear Top cover
Identify the rear top cover location highlighted in blue.
Align with the tabs, then slide the rear top cover forward until it fits into place.
Front Top Cover
Identify the front top cover location highlighted in blue.
Align the tabs on the front top cover with the guide slots on the system.
Push the front top cover latch down.
Using a 1/4-inch flathead or a Phillips #2 screwdriver, rotate the lock clockwise.
Front Bezel
Identify the front bezel location highlighted in blue.
Hook the right end of the front bezel onto the system.
Fit the free end of the front bezel onto the system.
Lock the front bezel with the key.