- Notes, cautions, and warnings
- Dell PowerEdge M630p overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- Viewing System BIOS
- System BIOS Settings details
- Boot Settings
- Network Settings
- System Security
- System Information
- Memory Settings
- Processor Settings
- SATA Settings
- Integrated Devices
- Serial Communication
- System Profile Settings
- Miscellaneous Settings
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing server module components
- Safety instructions
- Recommended tools
- Installing and removing a server module
- System cover
- Inside the server module
- System memory
- Cooling shroud
- Processor blank and DIMM blank
- PCIe mezzanine cards
- Internal dual SD module (optional)
- rSPI card (optional)
- SD vFlash card
- Network Daughter Card
- Processors
- Hard drives or SSDs
- Hard drive or SSD bay numbering
- Hard drive or SSD installation guidelines
- Removing a hard drive or SSD
- Installing a hard drive or SSD
- Removing a hard drive or SSD blank
- Installing a hard drive or SSD blank
- Shutdown procedure for servicing a hard drive
- Configuring the boot drive
- Removing a 2.5-inch hard drive or SSD from a 2.5-inch hard drive or SSD carrier
- Installing a 2.5-inch hard drive or SSD in a 2.5-inch hard-drive or SSD carrier
- Removing a 1.8-inch SSD from a 1.8-inch SSD carrier
- Installing a 1.8-inch SSD in a 1.8-inch SSD carrier
- Removing the hard drive or SSD cage
- Installing the hard drive or SSD cage
- Hard drive or SSD backplane
- Storage controller card
- System board
- System battery
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Getting help
Dell PowerEdge M630 Systems (VRTX Enclosure) Owner's Manual
Installing a server module
Prerequisites
CAUTION: Many
repairs may only be done by a certified service technician. You should
only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service
and support team. Damage due to servicing that is not authorized by
Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
CAUTION: To prevent
damage to the I/O connectors, do not touch connectors or the connector
pins.
NOTE: Before
installing the server modules, place the chassis in the location that
you want.
NOTE: Install the server module partitions to install half-height server
module(s). For more information, see the Dell PowerEdge VRTX Enclosure
Owner’s Manual at Dell.com/poweredgemanuals.
Steps
- If you are installing a new server module, remove the plastic cover from the I/O connector(s) and save for future use.
- Orient the server module so that the module
handle is on the left side of the server module.CAUTION: While installing the server modules, ensure that they are properly aligned with the slots, to prevent damage to the server module connectors.
- Align the server module with the server module slot and guide rails on the enclosure.
- Slide the server module into the enclosure
until the module release handle engages and the server module is locked
in place.
Figure 1. Installing the I/O connector cover 
- server module cover
- I/O connector cover
Figure 2. Installing a server module 
- PCIe label on server moduleNOTE: This label indicates that the server module is configured specifically for the VRTX enclosure.
- VRTX enclosure
- server module
Next steps
- Turn on the server module.
- If applicable, install the front bezel of the PowerEdge VRTX enclosure.
Geef een beoordeling (1-5 sterren).
Geef een beoordeling (1-5 sterren).
Geef een beoordeling (1-5 sterren).
Selecteer of het artikel nuttig is of niet.
Opmerkingen mogen geen speciale tekens bevatten: <>() \