- Notes, cautions, and warnings
- Dell PowerEdge M630p overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- Viewing System BIOS
- System BIOS Settings details
- Boot Settings
- Network Settings
- System Security
- System Information
- Memory Settings
- Processor Settings
- SATA Settings
- Integrated Devices
- Serial Communication
- System Profile Settings
- Miscellaneous Settings
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing server module components
- Safety instructions
- Recommended tools
- Installing and removing a server module
- System cover
- Inside the server module
- System memory
- Cooling shroud
- Processor blank and DIMM blank
- PCIe mezzanine cards
- Internal dual SD module (optional)
- rSPI card (optional)
- SD vFlash card
- Network Daughter Card
- Processors
- Hard drives or SSDs
- Hard drive or SSD bay numbering
- Hard drive or SSD installation guidelines
- Removing a hard drive or SSD
- Installing a hard drive or SSD
- Removing a hard drive or SSD blank
- Installing a hard drive or SSD blank
- Shutdown procedure for servicing a hard drive
- Configuring the boot drive
- Removing a 2.5-inch hard drive or SSD from a 2.5-inch hard drive or SSD carrier
- Installing a 2.5-inch hard drive or SSD in a 2.5-inch hard-drive or SSD carrier
- Removing a 1.8-inch SSD from a 1.8-inch SSD carrier
- Installing a 1.8-inch SSD in a 1.8-inch SSD carrier
- Removing the hard drive or SSD cage
- Installing the hard drive or SSD cage
- Hard drive or SSD backplane
- Storage controller card
- System board
- System battery
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Getting help
Dell PowerEdge M630 Systems (VRTX Enclosure) Owner's Manual
Miscellaneous Settings details
About this task
- Option
- Description
- System Time
- Enables you to set the time on the system.
- System Date
- Enables you to set the date on the system.
- Asset Tag
- Specifies the asset tag and enables you to modify it for security and tracking purposes.
- Keyboard NumLock
- Enables you to set whether the system boots with the
NumLock enabled or disabled. This option is set to On by default.NOTE: This option does not apply to 84-key keyboards.
- F1/F2 Prompt on Error
- Enables or disables the F1/F2 prompt on error. This option is set to Enabled by default. The F1/F2 prompt also includes keyboard errors.
- Load Legacy Video Option ROM
- Enables you to determine whether the system BIOS loads the legacy video (INT 10H) option ROM from the video controller. Selecting Enabled in the operating system does not support UEFI video output standards. This field is available only for UEFI boot mode. You cannot set the option to Enabled if UEFI Secure Boot mode is enabled.
- In-System Characterization
- Enables or disables In-System Characterization. This option is set to Disabled by default.
The two other options are Enabled and Enabled - No Reboot.NOTE: The default setting for In-System Characterization is subject to change in future BIOS releases.
When enabled, In-System Characterization (ISC) executes during POST upon detecting relevant changes in system configuration to optimize system power and performance. ISC takes about 20 seconds to execute, and system reset is needed for ISC results to be applied. The Enabled - No Reboot option executes ISC and continues without applying ISC results until the next time system reset occurs. The Enabled option executes ISC and forces an immediate system reset so that ISC results can be applied. It takes the system longer to be ready due to the forced system reset. When disabled, ISC does not execute.
Geef een beoordeling (1-5 sterren).
Geef een beoordeling (1-5 sterren).
Geef een beoordeling (1-5 sterren).
Selecteer of het artikel nuttig is of niet.
Opmerkingen mogen geen speciale tekens bevatten: <>() \