Prerequisites
Save and close all open files and exit all open applications.
Shut down your computer. For Windows operating system, click Start > Image: Power button Power > Shut down.
NOTE:If you are using a different operating system, see the documentation of your operating system for shut-down instructions.
Turn off all the attached peripherals.
Disconnect your computer and all attached devices from their electrical outlets.
Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.
CAUTION: To disconnect a network cable, unplug the cable from your computer.
Remove any media card and optical disc from your computer, if applicable.
Removing the side cover:
Loosen the two captive screws that secure the side cover to the chassis.
Slide the side cover towards the back of the computer.
Lift the side cover from the chassis.
Removing the 2.5-inch hard drive:
Disconnect the data and power cables from the hard drive.
Remove the screw (#6-32) that secures the hard drive carrier to the chassis.
Remove the four screws (M3x3.5) that secure the hard drive to the hard-drive carrier.
Slide and lift the 2.5-inch hard drive off the hard-drive carrier.
NOTE: Note the orientation or the SATA connector marking on the hard-drive carrier so that you can replace it correctly.
Removing the 3.5-inch hard drive:
Disconnect the data and power cables from the hard drive.
Remove the two screws (6-32) that secure the hard-drive carrier to the chassis.
Slide the hard-drive carrier away from the chassis and lift hard-drive carrier out of the disk-drive cage.
Remove the two screws (6-32) that secure the hard drive to the hard-drive carrier.
Slide and remove the hard drive from the hard-drive carrier.
Removing the disk-drive cage:
If the optical drive is installed, remove the data and power cables from the routing points on the disk-drive cage.
Remove the single (6-32) screw to release the disk-drive cage from the chassis..
Lift the disk-drive and detach it from the mounting points on the chassis.
Rotate the drive-cage and place it on the chassis.
If the optical drive is installed, disconnect the power and data cables from the connectors on the optical drive.
Lift the disk-drive cage away from the computer.
Removing the processor fan and heat-sink assembly:
Disconnect the processor-fan cable from the connector on the system board.
In the reverse sequential order (4->3->2->1), loosen the captive screws that secure the processor fan and heat-sink assembly to the system board.
Lift the processor fan and heat-sink assembly off the system board.
Removing the processor:
Press the release lever down and then push it away from the processor to release it from the securing tab.
Extend the release lever completely and open the processor cover.
CAUTION: When removing the processor, do not touch any of the pins inside the socket or allow any objects to fall on the pins in the socket.
Gently lift the processor from the processor socket.
Installing the processor:
Ensure that the release lever on the processor socket is fully extended in the open position.
NOTE: The pin-1 corner of the processor has a triangle that aligns with the triangle on the pin-1 corner on the processor socket. When the processor is properly seated, all four corners are aligned at the same height. If one or more corners of the processor are higher than the others, the processor is not seated properly.
Align the notches on the processor with the tabs on the processor socket and place the processor in the processor socket.
CAUTION: Ensure that the processor-cover notch is positioned underneath the alignment post.
When the processor is fully seated in the socket, pivot the release-lever down and place it under the tab on the processor cover.
Installing the processor fan and heat-sink assembly:
Place the processor fan and heat-sink assembly on the system board and align the captive screws to the screw holes on the system board.
Tighten the four captive screws that secure the heat stink to the system board.
Connect the processor-fan cable to the connector on the system board.
Installing the disk-drive cage:
Place the disk-drive cage upside down on the chassis.
If the optical drive is installed, connect the data and power cable to the connectors on the optical drive.
Hold the disk-drive cage upright and align the mounting points on the disk-drive cage with the slots on the chassis.
Align the screw hole on the cage with the screw hole on the chassis.
Install the single (6-32) screw to secure the disk-drive cage in place.
If the optical drive is installed, route the power and data cables through the routing guide on the disk-drive cage.
Installing the 3.5-inch hard drive:
Slide the hard drive into the hard-drive carrier.
Replace the two screws (6-32) to secure the hard drive to the hard-drive carrier.
Align the tabs on the hard-drive carrier with the slots on the chassis and snap the hard-drive carrier onto the disk-drive cage.
Replace the two screws (6-32) to secure the hard drive carrier on the chassis.
Connect the data and power cables to the connectors on the hard drive.
Installing the 2.5-inch hard drive:
Insert and align the hard drive into the hard-drive carrier.
Replace the four screws (M3x3) that secure the hard drive to the hard-drive carrier.
Align the tabs on the hard-drive carrier with the slots on the chassis and snap the hard-drive carrier into place.
Replace the screw (#6-32) to secure the hard-drive carrier to the chassis.
Connect the data and power cables to the connectors on the hard drive.
Installing the front bezel:
Align the front-cover tabs with the slots on the chassis.
Rotate the front cover towards the chassis and snap it into place.
Installing the side cover:
Align the tabs on the side cover with the slots on the chassis.
Slide the side cover towards the front of the computer.
Tighten the two captive screws to secure the side cover to the chassis.
Replace all screws and ensure that no stray screws remain inside your computer.
Connect any external devices, peripherals, or cables you removed before working on your computer.
Replace any media cards, discs, or any other components that you removed before working on your computer.
Connect your computer and all attached devices to their electrical outlets.
Turn on your computer.
