ECS: RAP015: temperaturfeil; Symptom Code: 2010

Summary: En temperatursensor på noden rapporterer på et kritisk nivå er nådd.

This article applies to This article does not apply to This article is not tied to any specific product. Not all product versions are identified in this article.
Check out other resources

Symptoms

En temperatursensor har oppdaget en temperatur som er over en kritisk terskel.
Det kan hende at en komponent ikke fungerer som den skal, noe som får en temperatursensor til å rapportere at et kritisk nivå er nådd.
En temperatursensor på noden rapporterer at et kritisk nivå er nådd.

Cause

Det har oppstått et problem som førte til at en temperatursensor gikk over et kritisk nivå.

Resolution

For Gen2, bla til bunnen.

3. generasjons maskinvare: 

1. Kontroller statusen til temperatursensorene ved hjelp av cs_hal på den rapporterte noden.

Kommandoen:  
#cs_hal sensors temp
 
Eksempel: For Gen3 er det bare tre Temp-sensorer som følger.
  
admin@n1-mgmt:~>  cs_hal sensors temp
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      53 Degrees Celsius
Processor         Temperature         Temp              OK      54 Degrees Celsius
System Board      Temperature         Inlet Temp        CRIT    40 Degrees Celsius; above critical threshold
System Board      Temperature         Exhaust Temp      OK      50 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.
admin@n1-mgmt:~>
2. Kontroller alle noder i racket og se om andre noder rapporterer temp-sensoren ikke "OK"

Kommando:  
viprexec -i  cs_hal sensors temp

Eksempel: I dette eksemplet rapporterer flere noder i øvre halvdel av racket innløpstemperaturen for høy.  
admin@n1-mgmt:~> viprexec -i  cs_hal sensors temp

Output from host : 192.168.219.1
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      53 Degrees Celsius
Processor         Temperature         Temp              OK      53 Degrees Celsius
System Board      Temperature         Inlet Temp        CRIT    40 Degrees Celsius; above critical threshold
System Board      Temperature         Exhaust Temp      OK      50 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.

Output from host : 192.168.219.2
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      47 Degrees Celsius
Processor         Temperature         Temp              OK      49 Degrees Celsius
System Board      Temperature         Inlet Temp        CRIT    39 Degrees Celsius; above critical threshold
System Board      Temperature         Exhaust Temp      OK      50 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.

Output from host : 192.168.219.3
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      46 Degrees Celsius
Processor         Temperature         Temp              OK      46 Degrees Celsius
System Board      Temperature         Inlet Temp        OK      35 Degrees Celsius
System Board      Temperature         Exhaust Temp      OK      47 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.

Output from host : 192.168.219.4
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      48 Degrees Celsius
Processor         Temperature         Temp              OK      50 Degrees Celsius
System Board      Temperature         Inlet Temp        OK      35 Degrees Celsius
System Board      Temperature         Exhaust Temp      OK      47 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.

Output from host : 192.168.219.5
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      48 Degrees Celsius
Processor         Temperature         Temp              OK      50 Degrees Celsius
System Board      Temperature         Inlet Temp        WARN    38 Degrees Celsius; above non-critical threshold
System Board      Temperature         Exhaust Temp      OK      49 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.

Output from host : 192.168.219.6
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      50 Degrees Celsius
Processor         Temperature         Temp              OK      52 Degrees Celsius
System Board      Temperature         Inlet Temp        CRIT    39 Degrees Celsius; above critical threshold
System Board      Temperature         Exhaust Temp      OK      51 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.

Output from host : 192.168.219.7
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      45 Degrees Celsius
Processor         Temperature         Temp              OK      48 Degrees Celsius
System Board      Temperature         Inlet Temp        OK      36 Degrees Celsius
System Board      Temperature         Exhaust Temp      OK      47 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.

Output from host : 192.168.219.8
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      51 Degrees Celsius
Processor         Temperature         Temp              OK      49 Degrees Celsius
System Board      Temperature         Inlet Temp        OK      31 Degrees Celsius
System Board      Temperature         Exhaust Temp      OK      43 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.

Output from host : 192.168.219.9
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      52 Degrees Celsius
Processor         Temperature         Temp              OK      51 Degrees Celsius
System Board      Temperature         Inlet Temp        OK      30 Degrees Celsius
System Board      Temperature         Exhaust Temp      OK      42 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.

Output from host : 192.168.219.10
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      54 Degrees Celsius
Processor         Temperature         Temp              OK      51 Degrees Celsius
System Board      Temperature         Inlet Temp        OK      28 Degrees Celsius
System Board      Temperature         Exhaust Temp      OK      41 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.
 192.168.219.7
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      45 Degrees Celsius
Processor         Temperature         Temp              OK      48 Degrees Celsius
System Board      Temperature         Inlet Temp        OK      36 Degrees Celsius
System Board      Temperature         Exhaust Temp      OK      47 Degrees Celsius

Output from host : 192.168.219.11
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      56 Degrees Celsius
Processor         Temperature         Temp              OK      55 Degrees Celsius
System Board      Temperature         Inlet Temp        OK      27 Degrees Celsius
System Board      Temperature         Exhaust Temp      OK      40 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.

Output from host : 192.168.219.12
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      59 Degrees Celsius
Processor         Temperature         Temp              OK      59 Degrees Celsius
System Board      Temperature         Inlet Temp        OK      26 Degrees Celsius
System Board      Temperature         Exhaust Temp      OK      38 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.

Output from host : 192.168.219.13
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      51 Degrees Celsius
Processor         Temperature         Temp              OK      49 Degrees Celsius
System Board      Temperature         Inlet Temp        OK      26 Degrees Celsius
System Board      Temperature         Exhaust Temp      OK      36 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.

Output from host : 192.168.219.14
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      57 Degrees Celsius
Processor         Temperature         Temp              OK      60 Degrees Celsius
System Board      Temperature         Inlet Temp        OK      26 Degrees Celsius
System Board      Temperature         Exhaust Temp      OK      38 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.

Output from host : 192.168.219.15
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      59 Degrees Celsius
Processor         Temperature         Temp              OK      59 Degrees Celsius
System Board      Temperature         Inlet Temp        OK      26 Degrees Celsius
System Board      Temperature         Exhaust Temp      OK      39 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.

Output from host : 192.168.219.16
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
Processor         Temperature         Temp              OK      56 Degrees Celsius
Processor         Temperature         Temp              OK      56 Degrees Celsius
System Board      Temperature         Inlet Temp        OK      26 Degrees Celsius
System Board      Temperature         Exhaust Temp      OK      38 Degrees Celsius

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.
admin@n1-mgmt:~>

3. Mulige scenarier:
  1. Én node som bare rapporterer en sensor eller flere: Hvis problemet oppstår på bare én node der temperaturen rapporterer at den ikke er "OK", indikerer dette sannsynligvis et delproblem eller at noden ikke har god luftstrøm på grunn av et mer sannsynlig internt problem enn et rackproblem.
  2. Flere noder er berørt, dette er mer et miljøproblem i selve racket eller mulig datasenteret


4. Kontroller at viftene kjører som de skal. Hvis ikke, kan det hende at en vifte må byttes ut.

Kommandoen: 

#cs_hal sensors fan
Eksempel:  
admin@ecs:~>cs_hal sensors fan

Output from host : 192.168.219.1
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
System Board      Fan                 Fan1              OK      12600 RPM
System Board      Fan                 Fan2              OK      12600 RPM
System Board      Fan                 Fan3              OK      16920 RPM
System Board      Fan                 Fan4              OK      16800 RPM
System Board      Fan                 Fan5              OK      17040 RPM
System Board      Fan                 Fan6              OK      16920 RPM
System Board      Fan                 Fan Redundancy    OK      fully redundant;

NOTE: on Axum and EX-series, use "sudo -i racadm getsensorinfo" to obtain sensor information.
3. Hvis alle viftene rapporterer OK, betyr det at det ikke er noen problemer med viftesystemene. Engasjer Power Edge-teamet for å sjekke om en del må byttes ut. Hvis noen vifter rapporterer problemet, følger du ECS: Ring hjem: Feil på viften; SymptomCode: 2008

4. Viktig: Bruk https://central.dell.com/case-lookup/  og slå opp PSNT (Product Serial Number Tag) for å kontrollere historikken. Sjekk hvor mange hendelser som har skjedd i løpet av de siste 3-6 månedene. Sjekk om problemet var vedvarende og påvirket flere noder, eller hvis et helt rack er berørt med innløpstemperatur som er høyere enn normalt, indikerer dette et vedvarende miljøproblem som skal løses. Ikke lukk saken som duplikat med mindre det foreligger en klar handlingsplan og konklusjoner for å løse temperaturproblemet. 

5. Hvis PE-teamet ikke finner et problem, eller hvis historikken inneholder mange forekomster fra samme varsel (i 3 måneder eller mer), må du konsultere en L2 over Swarm og forberede deg på å bestille en CE for å gjennomgå miljøforholdene til racket og nodene som er berørt. 
 
Gen 2: 
 
1. Kontroller statusen til temperatursensorene ved hjelp av cs_hal.
Eksempel: 
# cs_hal sensors temp
Entity            Type                Label             Status  Info
-----             -----               -----             -----   -----
System Board      Temperature         SSB Therm Trip    OK
System Board      Temperature         BB Inlet Temp     OK      32 Degrees Celsius
CPU (DCMI Compat) Temperature         HSBP Temp         OK      -222 Degrees Celsius
System Board      Temperature         SSB Temp          OK      60 Degrees Celsius
System Board      Temperature         BB BMC Temp       OK      51 Degrees Celsius
System Board      Temperature         P1 VR Temp        OK      38 Degrees Celsius
System Board      Temperature         IB Temp           OK      46 Degrees Celsius
System Board      Temperature         Exit Air Temp     OK      54 Degrees Celsius
Front Panel       Temperature         IOM Temp          OK      43 Degrees Celsius
Drive Backplane   Temperature         HSBP PSOC         OK      37 Degrees Celsius
Front Panel       Temperature         LAN NIC Temp      OK      67 Degrees Celsius
Power Supply      Temperature         PS1 Temperature   OK      34 Degrees Celsius
Power Supply      Temperature         PS2 Temperature   OK      34 Degrees Celsius
Processor         Temperature         P1 Therm Margin   OK      216 Degrees Celsius
Processor         Temperature         P2 Therm Margin   OK      206 Degrees Celsius
Processor         Temperature         P1 Therm Ctrl %   OK      0 Unspecified
Processor         Temperature         P2 Therm Ctrl %   OK      0 Unspecified
Processor         Temperature         P1 DTS Therm Mgn  OK      216 Degrees Celsius
Processor         Temperature         P2 DTS Therm Mgn  OK      206 Degrees Celsius
Processor         Temperature         P1 VRD Hot        OK
Processor         Temperature         P2 VRD Hot        OK
System Board      Temperature         DIMM Thrm Mrgn 1  OK      201 Degrees Celsius
System Board      Temperature         DIMM Thrm Mrgn 2  OK      200 Degrees Celsius
System Board      Temperature         DIMM Thrm Mrgn 3  OK      198 Degrees Celsius
System Board      Temperature         DIMM Thrm Mrgn 4  OK      197 Degrees Celsius
System Board      Temperature         Agg Thrm Mgn 1    OK      233 Degrees Celsius
2. Følg de samme trinnene som er Gen 3 (men ikke rapporter til PowerEdge). Flere detaljer vil bli oppdatert for Gen2 i fremtiden. 

Affected Products

ECS Appliance

Products

ECS Appliance
Article Properties
Article Number: 000046763
Article Type: Solution
Last Modified: 30 Apr 2024
Version:  6
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.