- Notes, cautions, and warnings
- Dell PowerEdge R730 system overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- Front bezel (optional)
- System cover
- Inside the system
- Cooling shroud
- Cooling fans
- Cooling fan assembly
- System memory
- Processors and heat sinks
- PCIe card holder
- Cable retention bracket
- Integrated storage controller card
- Expansion cards and expansion card riser
- Expansion card installation guidelines
- Removing an expansion card from expansion card riser 2 or 3
- Installing an expansion card into the expansion card riser 2 or 3
- Removing an expansion card from the expansion card riser 1
- Installing an expansion card into the expansion card riser 1
- Removing the riser 1 blank
- Installing the riser 1 blank
- Removing expansion card risers
- Installing expansion card risers
- GPU card installation guidelines
- Removing the GPU card
- Installing a GPU card
- IDSDM
- Network daughter card
- Internal USB memory key (optional)
- System battery
- Power supply units (PSU)
- System board
- Trusted Platform Module
- Hard drives
- Removing a 2.5-inch hard drive blank
- Installing a 2.5-inch hard drive blank
- Removing a 3.5-inch hard drive blank
- Installing a 3.5-inch hard drive blank
- Removing a hot swappable hard drive or solid state drive
- Installing a hot swappable hard drive or solid state drive
- Removing a hard drive or a solid state drive from a hard drive carrier
- Installing a hard drive or solid state drives into a hard drive carrier
- Removing a 1.8-inch hard drive blank
- Installing a 1.8-inch hard drive blank
- Removing a 1.8-inch hard drive from a hard drive carrier
- Installing a 1.8-inch hard drive into a hard drive carrier
- Hard drive backplane
- Tape backup unit (optional)
- Optical drive (optional)
- SD vFlash card (optional)
- Control panel assembly
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Troubleshooting system startup failure
- Troubleshooting external connections
- Troubleshooting the video subsystem
- Troubleshooting a USB device
- Troubleshooting iDRAC Direct - USB XML configuration
- Troubleshooting iDRAC Direct - Laptop connection
- Troubleshooting a serial input and output device
- Troubleshooting a NIC
- Troubleshooting a wet system
- Troubleshooting a damaged system
- Troubleshooting the system battery
- Troubleshooting power supply units
- Troubleshooting cooling problems
- Troubleshooting cooling fans
- Troubleshooting system memory
- Troubleshooting an internal USB key
- Troubleshooting a micro SD card
- Troubleshooting an optical drive
- Troubleshooting a tape backup unit
- Troubleshooting a drive or SSD
- Troubleshooting a storage controller
- Troubleshooting expansion cards
- Troubleshooting processors
- System messages
- Getting help
Velkommen
Dell-websteder
Dell-websteder
Velkommen hos Dell
Min konto
- Afgiv ordrer hurtigt og nemt
- Se ordrer og spor status for din forsendelse
- Opret og få adgang til en liste med dine produkter
- Administrer dine Dell EMC-websteder, -produkter og -kontaktpersoner på produktniveau ved hjælp af Company Administration (Virksomhedsadministration).
Dell PowerEdge R730 Owner's Manual
SATA Settings details
About this task
- Option
- Description
- Embedded SATA
- Enables the embedded SATA option to be set to Off, ATA, AHCI, or RAID modes. This option is set to AHCI by default.
- Security Freeze Lock
- Sends Security Freeze Lock command to the Embedded SATA drives during POST. This option is applicable only for ATA and AHCI modes.
- Write Cache
- Enables or disables the command for Embedded SATA drives during POST.
- Port A
- Sets the drive type of the selected device. For Embedded
SATA settings in ATA mode, set
this field to Auto to enable BIOS support.
Set it to OFF to turn off BIOS support.
For AHCI or RAID mode, BIOS support is always enabled.
- Option
- Description
- Model
- Specifies the drive model of the selected device.
- Drive Type
- Specifies the type of drive attached to the SATA port.
- Capacity
- Specifies the total capacity of the hard drive. This field is undefined for removable media devices such as optical drives.
- Port B
- Sets the drive type of the selected device. For Embedded
SATA settings in ATA mode, set
this field to Auto to enable BIOS support.
Set it to OFF to turn off BIOS support.
For AHCI or RAID mode, BIOS support is always enabled.
- Option
- Description
- Model
- Specifies the drive model of the selected device.
- Drive Type
- Specifies the type of drive attached to the SATA port.
- Capacity
- Specifies the total capacity of the hard drive. This field is undefined for removable media devices such as optical drives.
- Port C
- Sets the drive type of the selected device. For Embedded SATA settings in ATA mode,
set this field to Auto to enable BIOS support.
Set it to OFF to turn off BIOS support.
For AHCI or RAID mode, BIOS support is always enabled.
- Option
- Description
- Model
- Specifies the drive model of the selected device.
- Drive Type
- Specifies the type of drive attached to the SATA port.
- Capacity
- Specifies the total capacity of the hard drive. This field is undefined for removable media devices such as optical drives.
- Port D
- Sets the drive type of the selected device. For Embedded SATA settings in ATA mode,
set this field to Auto to enable BIOS support.
Set it to OFF to turn off BIOS support.
For AHCI or RAID mode, BIOS support is always enabled.
- Option
- Description
- Model
- Specifies the drive model of the selected device.
- Drive Type
- Specifies the type of drive attached to the SATA port.
- Capacity
- Specifies the total capacity of the hard drive. This field is undefined for removable media devices such as optical drives.
- Port E
- Sets the drive type of the selected device. For Embedded SATA settings in ATA mode,
set this field to Auto to enable BIOS support.
Set it to OFF to turn off BIOS support.
For AHCI or RAID mode, BIOS support is always enabled.
- Option
- Description
- Model
- Specifies the drive model of the selected device.
- Drive Type
- Specifies the type of drive attached to the SATA port.
- Capacity
- Specifies the total capacity of the hard drive. This field is undefined for removable media devices such as optical drives.
- Port F
- Sets the drive type of the selected device. For Embedded SATA settings in ATA mode,
set this field to Auto to enable BIOS support.
Set it to OFF to turn off BIOS support.
For AHCI or RAID mode, BIOS support is always enabled.
- Option
- Description
- Model
- Specifies the drive model of the selected device.
- Drive Type
- Specifies the type of drive attached to the SATA port.
- Capacity
- Specifies the total capacity of the hard drive. This field is undefined for removable media devices such as optical drives.
- Port G
- Sets the drive type of the selected device. For Embedded SATA settings in ATA mode,
set this field to Auto to enable BIOS support.
Set it to OFF to turn off BIOS support.
For AHCI or RAID mode, BIOS support is always enabled.
- Option
- Description
- Model
- Specifies the drive model of the selected device.
- Drive Type
- Specifies the type of drive attached to the SATA port.
- Capacity
- Specifies the total capacity of the hard drive. This field is undefined for removable media devices such as optical drives.
- Port H
- Sets the drive type of the selected device. For Embedded SATA settings in ATA mode,
set this field to Auto to enable BIOS support.
Set it to OFF to turn off BIOS support.
For AHCI or RAID mode, BIOS support is always enabled.
- Option
- Description
- Model
- Specifies the drive model of the selected device.
- Drive Type
- Specifies the type of drive attached to the SATA port.
- Capacity
- Specifies the total capacity of the hard drive. This field is undefined for removable media devices such as optical drives.
- Port I
- Sets the drive type of the selected device. For Embedded SATA settings in ATA mode,
set this field to Auto to enable BIOS support.
Set it to OFF to turn off BIOS support.
For AHCI or RAID mode, BIOS support is always enabled.
- Option
- Description
- Model
- Specifies the drive model of the selected device.
- Drive Type
- Specifies the type of drive attached to the SATA port.
- Capacity
- Specifies the total capacity of the hard drive. This field is undefined for removable media devices such as optical drives.
- Port J
- Sets the drive type of the selected device. For Embedded SATA settings in ATA mode,
set this field to Auto to enable BIOS support.
Set it to OFF to turn off BIOS support.
For AHCI or RAID mode, BIOS support is always enabled.
- Option
- Description
- Model
- Specifies the drive model of the selected device.
- Drive Type
- Specifies the type of drive attached to the SATA port.
- Capacity
- Specifies the total capacity of the hard drive. This field is undefined for removable media devices such as optical drives.
Angiv vurderinger (1-5 stjerner).
Angiv vurderinger (1-5 stjerner).
Angiv vurderinger (1-5 stjerner).
Angiv, om artiklen var nyttig eller ej.
Kommentarer må ikke indeholde følgende specialtegn: <>()\