Integrated NIC | Allows you to
configure the integrated network controller. Click one of the following options:
- Disabled
- Enabled
- Enabled w/PXE—Default
|
UEFI Network Stack | Allows pre-OS and early OS networking features to use any enabled NICs.
- Enabled UEFI Network Stack
This option is set by default. |
Serial Port | Identifies and
defines the serial port settings. You can set the serial port to:
- Disabled
- COM1—Default
- COM2
- COM3
- COM4
NOTE:The operating
system may allocate resources even if the setting is disabled. |
SATA Operation | |
7820 Tower | Allows
you to configure the operating mode of the integrated SATA hard-drive controller. Click one of the following options:
- Disabled
- AHCI
- RAID On—Default
NOTE:SATA is
configured to support RAID mode. |
Drives | |
7820 Tower | Allows you to enable or disable various drives on board. The options are:
- MiniSAS PCIe SSD-0
- SATA-0
- SATA–2
- SATA–4
- ODD–0
- MiniSAS PCIe SSD-1
- SATA–1
- SATA–3
- SATA–5
- ODD–1
All the options are set by default. |
PCIe Drives | Allows the enabling of Front PCIe attached
Ports.
- MiniSAS PCIe SSD-0
- MiniSAS PCIe SSD-1
- MiniSAS PCIe SSD-2
- MiniSAS PCIe SSD-3
All the options are set by default. |
SMART Reporting | This field controls
if the hard drive errors for the integrated drives are reported during
system startup. This technology is part of the SMART(Self-Monitoring
Analysis and Reporting Technology) specification. This option is not set by default. |
USB Configuration | Allows you to
enable or disable the internal USB configuration. The options are:
- Enable USB Boot Support
- Enable Front USB Ports
- Enable Internal USB Ports
- Enable USB 3.0 Controller
- Enable Rear USB Ports
All the options are set by default. |
Front USB Configuration | Allows you to
enable/disable Front USB ports. The options are:
- USB3 Type A *
- USB Type C port 2 (Right) *
- USB Type C port 1 (Right) *
All the options are set by default. |
Rear USB Configuration | Allows you to
enable/disable Rear USB ports. The options are:
- RearPort3 Top *
- RearPort1 Top *
- RearPort2 Top *
- RearPort3 Bottom *
- RearPort1 Bottom *
- RearPort2 Bottom *
All the options are set by default. |
Internal USB Configuration | Allows you to
enable/disable Internal USB ports. This option is set by default. |
Dell Type-C Dock Configuration | Allows you to
connect to Dell WD and TB family of docks. Always Allows Dell DocksThis option is set by default. |
Thunderbolt Adapter Configuration | Allows you to
enable or disable the Thunderbolt device support capability. The options are:
- Enabled Thunderbolt Technology Support
- Enabled Thunderbolt Adapter Pre-boot Modules
- Enabled Thunderbolt Adapter Boot Support—Default
NOTE:The security level configures the Thunderbolt adapter security settings within the operating system. |
USB PowerShare | Allows you to configure the USB PowerShare feature behavior. This option is not set by default. |
Audio | Allows you to enable
or disable the integrated audio controller. This option is set by default. |
Memory Map IO above 4GB | Allows you to enable
or disable 64-bit capable PCI devices to be decoded in above 4 GB address space(only if the system supports 64-bit PCI decoding). This option is not set by default. |
HDD Fans | Allows you to
control the HDD fans. The options are: - HDD1 Fan Enable
- HDD2 Fan Enable
- HDD3 Fan Enable
All the options are not set by default. |
Miscellaneous devices | Allows you to
enable or disable various on board devices. The options are:
- Enable PCI Slot—Default
- Secure Digital (SD) Card Boot
- Enable Secure Digital (SD) Card—Default
- Secure Digital (SD) Card Read-Only Mode
|
Intel VMD Technology | Allows you to enable or disable VMD on the front PCIe bays.
- PCIE0
- PCIE1
- PCIE0_CPU0
- PCIE1_CPU0
All the options are not set by default. Allows you to disable VMD for the PCIE Slots |