- Notes, Cautions, and Warnings
- About This Guide
- About the SCv3000 and SCv3020 Storage System
- Storage Center Hardware Components
- Storage Center Communication
- Front-End Connectivity
- Back-End Connectivity
- System Administration
- Storage Center Replication
- SCv3000 and SCv3020 Storage System Hardware
- SCv3000 and SCv3020 Storage System Front-Panel View
- SCv3000 and SCv3020 Storage System Back-Panel View
- Expansion Enclosure Overview
- Install the Storage Center Hardware
- Connect the Front-End Cabling
- Types of Redundancy for Front-End Connections
- Connecting to Host Servers with Fibre Channel HBAs
- Connecting to Host Servers with iSCSI HBAs or Network Adapters
- Connecting to Host Servers with SAS HBAs
- Attach Host Servers (Fibre Channel)
- Attach the Host Servers (iSCSI)
- Attach the Host Servers (SAS)
- Connect the Management Ports to the Management Network
- Connect the Back-End Cabling
- Deploy the Storage Center
- Preparing for Deployment
- Deploying the Storage Center Using Unisphere
- Unisphere Discovery Utility
- Deploying the Storage Center Using Storage Manager Client
- Install and Use the Storage Manager Client
- Introduction to Storage Center Initial Configuration
- Select a Storage Center to Initialize
- Welcome Page
- Customer Installation Authorization
- Set System Information
- Set Administrator Information
- Confirm the Storage Center Configuration
- Deploy the Storage Center
- Configure Key Management Server Settings
- Create a Storage Type
- Fault Tolerance
- Inherit Settings
- Configure Time Settings
- Configure SMTP Server Settings
- Set Up SupportAssist
- Accept the SupportAssist Collection Agreement
- Provide Contact Information
- Provide Site Contact Information
- Validate the SupportAssist Connection
- Update Storage Center
- Complete Configuration and Perform Next Steps
- Perform Post-Setup Tasks
- Adding or Removing Expansion Enclosures
- Adding Expansion Enclosures to a Storage System Deployed Without Expansion Enclosures
- Install New SCv300 and SCv320 Expansion Enclosures in a Rack
- Add the SCv300 and SCv320 Expansion Enclosures to the A-Side of the Chain
- Add the SCv300 and SCv320 Expansion Enclosures to the B-Side of the Chain
- Install New SCv360 Expansion Enclosures in a Rack
- Add the SCv360 Expansion Enclosures to the A-Side of the Chain
- Add an SCv360 Expansion Enclosure to the B-Side of the Chain
- Adding a Single Expansion Enclosure to a Chain Currently in Service
- Removing an Expansion Enclosure from a Chain Currently in Service
- Release the Drives in the Expansion Enclosure
- Disconnect the SCv300 and SCv320 Expansion Enclosure from the A-Side of the Chain
- Disconnect the SCv300 and SCv320 Expansion Enclosure from the B-Side of the Chain
- Disconnect the SCv360 Expansion Enclosure from the A-Side of the Chain
- Disconnect the SCv360 Expansion Enclosure from the B-Side of the Chain
- Adding Expansion Enclosures to a Storage System Deployed Without Expansion Enclosures
- Troubleshooting Storage Center Deployment
- Set Up a Local Host or VMware Host
- Worksheet to Record System Information
SCv3000 and SCv3020 Storage System Deployment Guide
Troubleshooting Hard Drives
To troubleshoot hard drives:
Steps
- Check the status of the hard drive using Storage Manager.
- Determine the status of the hard drive indicators.
- If the hard drive status indicator blinks amber ON for two seconds and OFF for one second, the hard drive has failed.
- If the hard drive status indicator is not lit, proceed to the next step.
- Check the connectors and reseat the hard drive.
CAUTION: Perform this step only on unmanaged drives or after you confirm that the particular drive contains no user data. The Fault LED alone is not an indication that you can safely remove the drive.
- Remove the hard drive.
- Check the hard drive and the backplane to ensure that the connectors are not damaged.
- Reinstall the hard drive. Make sure the hard drive makes contact with the backplane.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\