- Notes, cautions, and warnings
- Dell PowerEdge T630 server overview
- Converting the system from tower mode to rack mode
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing system components
- Safety instructions for converting system from tower to rack
- Before working inside your system
- After working inside your system
- Recommended tools
- Front bezel (optional)
- System feet
- Caster wheels – optional
- System cover
- Inside the system
- Cooling shroud
- Cooling fans
- Cooling-fan assembly (optional)
- System memory
- Flex bays
- Hard drives
- Removing a hot swappable hard drive or solid state drive
- Installing a hot swappable hard drive
- Removing a 2.5-inch hard drive blank
- Installing a 2.5-inch hard drive blank
- Removing a 3.5-inch hard drive blank
- Installing a 3.5-inch hard drive blank
- Installing a 2.5-inch hard drive into a 3.5-inch hard drive adapter
- Removing a 2.5-inch hard drive from a 3.5-inch hard drive adapter
- Installing a 3.5-inch hard drive adapter into a hot swap hard drive carrier
- Removing a 3.5-inch hot swappable hard drive adapter from a 3.5-inch hot swappable hard drive carrier
- Removing a hard drive or a solid state drive from a hard drive carrier
- Installing a hot swappable hard drive into a hot swappable hard drive carrier
- Optical drives and tape drives
- Internal USB memory key (optional)
- Expansion card holder
- Expansion cards
- GPU card holder (optional)
- GPU cards (optional)
- Internal dual SD module (optional)
- Internal SD card
- Processors and heat sinks
- Power supply unit
- System battery
- Hard drive backplane
- SD vFlash card (optional)
- Control panel assembly
- System board
- Trusted Platform Module
- Power interposer board and power distribution board
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Troubleshooting system startup failure
- Troubleshooting external connections
- Troubleshooting the video subsystem
- Troubleshooting a USB device
- Troubleshooting a serial input and output device
- Troubleshooting a NIC
- Troubleshooting a wet system
- Troubleshooting a damaged system
- Troubleshooting the system battery
- Troubleshooting power supply units
- Troubleshooting cooling problems
- Troubleshooting cooling fans
- Troubleshooting system memory
- Troubleshooting an internal USB key
- Troubleshooting a micro SD card
- Troubleshooting an optical drive
- Troubleshooting a drive or SSD
- Troubleshooting a storage controller
- Troubleshooting expansion cards
- Troubleshooting processors
- Getting help
Välkommen
Dells webbplatser
Dells webbplatser
Välkommen till Dell
Mitt konto
- Lägg beställningar snabbt och enkelt
- Visa beställningar och kontrollera leveransstatus
- Skapa och kom åt en lista över dina produkter
- Hantera dina webbplatser, produkter och kontakter på produktnivå från Dell EMC med hjälp av företagsadministration.
Dell PowerEdge T630 Owner's Manual
Replacing an optional SD vFlash media card
Steps
- Locate the SD vFlash media slot on the system.
- To remove the SD vFlash media card, push the card inward to release it, and pull the card from the card slot.
Figure 1. Removing the SD vFlash media card 
- SD vFlash media card
- SD vFlash media card slot
- To install an SD vFlash media card, with the label side facing up, insert the contact-pin end of the SD vFlash media card into the card slot on the module.
NOTE: The slot is keyed to ensure correct insertion of the card.
- Press the card inward to lock it into the slot.
Figure 2. Installing the SD vFlash media card 
- SD vFlash media card
- SD vFlash media card slot
Ange betyg (1–5 stjärnor).
Ange betyg (1–5 stjärnor).
Ange betyg (1–5 stjärnor).
Ange om artikeln var användbar eller inte.
Kommentarer får inte innehålla följande specialtecken: <>()\