- Notes, cautions, and warnings
- About your system
- Initial system configuration
- Before You Begin
- Initial Setup Sequence
- Initial CMC Network Configuration
- Logging In To The CMC Using The Web-Based Interface
- Adding And Managing CMC Users
- Configuring iDRAC Networking Using The Web-Based Interface
- Setting The First Boot Device For Servers
- Configuring And Managing Power
- Installing Or Updating The CMC Firmware
- Configuring The Optional iKVM Switch Module
- FlexAddress
- FlexAddress Plus
- Configuring The I/O Modules
- Network Information
- I/O Connectivity
- Port Auto-Disablement in Quad-Port Network Daughter Card (Dell PowerEdge M710HD Only)
- Mezzanine Cards
- I/O Module Port Mapping—Full-Height Blades
- I/O Module Port Mapping─Half-Height Blades
- I/O Modules—Switches
- Configuring A Switch Module Network Ethernet Port Using The Web-Based Interface
- Brocade M6505 16 Gbps FC SAN I/O Module
- Cisco Nexus B22 Fabric Extender Module
- Dell PowerEdge M I/O Aggregator Switch
- Dell Force10 MXL 10/40 GbE Switch
- Mellanox M4001F/M4001Q/M4001T Infiniband Switch I/O Module
- Dell PowerConnect KR 8024-k Switch
- Dell PowerConnect M8428-k 10 Gb Converged Network Switch
- Mellanox M2401G DDR Infiniband Switch I/O Module
- Mellanox M3601Q QDR Infiniband Switch I/O Module
- Cisco Catalyst Ethernet Switch I/O Modules
- Dell PowerConnect M6348 1 Gb Ethernet Switch I/O Module
- Dell PowerConnect M6220 Ethernet Switch I/O Module
- Dell PowerConnect M8024 10 Gb Ethernet Switch I/O Module
- Dell 8/4 Gbps FC SAN Module
- Brocade M5424 FC8 I/O Module
- I/O Modules—Pass-Through
- Installing Enclosure Components
- Troubleshooting The Enclosure
- Technical Specifications
- Getting help
Dell PowerEdge M1000e Enclosure Owner's Manual
Quad-Port Mezzanine Cards
The following table illustrates the I/O module port mapping for full-height blades with quad-port mezzanine cards.
NOTE: For a detailed mapping of each PowerEdge system, see
Quadport Capable Hardware for the M1000e Modular Chassis at
support.dell.com/manuals.
| Blade n and Blade (n + 8)
NOTE: n denotes a variable value from 1 to 8.
|
I/O Module | |||
|---|---|---|---|---|
| B1 | C1 | C2 | B2 | |
| Mezz_FAB_B_Blade n_Port1 | Portn | |||
| Mezz_FAB_B_Blade n_Port2 | Portn | |||
| Mezz_FAB_B_Blade n_Port3 | Port(n+16) | |||
| Mezz_FAB_B_Blade n_Port4 | Port(n+16) | |||
| Mezz_FAB_C_Blade n_Port1 | Portn | |||
| Mezz_FAB_C_Blade n_Port2 | Portn | |||
| Mezz_FAB_C_Blade n_Port3 | Port(n+16) | |||
| Mezz_FAB_C_Blade n_Port4 | Port(n+16) | |||
| Mezz_FAB_B_Blade n+8_Port1 | Port(n+8) | |||
| Mezz_FAB_B_Blade n+8_Port2 | Port(n+8) | |||
| Mezz_FAB_B_Blade n+8_Port3 | Port(n+24) | |||
| Mezz_FAB_B_Blade n+8_Port4 | Port(n+24) | |||
| Mezz_FAB_C_Blade n+8_Port1 | Port(n+8) | |||
| Mezz_FAB_C_Blade n+8_Port2 | Port(n+8) | |||
| Mezz_FAB_C_Blade n+8_Port3 | Port (n+24) | |||
| Mezz_FAB_C_Blade n+8_Port4 | Port(n+24) | |||
NOTE: Even though PowerEdge M610x is a full blade system, only two mezzanine card slots (MEZZ1_Fab_C1 and MEZZ2_FAB_B1) in the expansion bay are available for use. The other two slots on the system board (MEZZ1_FAB_C and MEZZ2_FAB_B) are occupied by the mezzanine interface card which provides connectivity between the PCIe expansion-card riser and the system board.
The following table illustrates the I/O module port mapping for PowerEdge M610x in bay n.
| Blade 1 | I/O Module | |||||
|---|---|---|---|---|---|---|
| A1 | B1 | C1 | C2 | B2 | A2 | |
| Mezzanine Card C (port 1 and port 2) | Port 9 | Port 9 | ||||
| Mezzanine Card C (port 3 and port 4) | Port 25 | Port 25 | ||||
| Mezzanine Card B (port 1 and port 2) | Port 9 | Port 9 | ||||
| Mezzanine Card B (port 1 and port 2) | Port 25 | Port 25 | ||||
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\