Connectrix MDS-9710

This document highlights minimum, recommended, and latest code versions for Dell Technologies Enterprise and Datacenter Infrastructure products. We carefully evaluate and monitor code deployment data to ensure that product releases meet our stringent expectations to provide our customers with reliable products and solutions.

M3 line card may be reset after system reports EOBC heartbeat failure:

Cisco MDS9700 DS-X9448-768K9: Link failure Link Reset failed nonempty recv queue errors seen after port hwfailure.

Learn how the MyService360 services analytics dashboard integrates the Dell AIOps (formerly CloudIQ) Health Score into the Install Base views. This integration streamlines services and product health management by IT admins using the MyService360 and Dell AIOps portals. Verify supported products by portal and access helpful Dell AIOps resources.

PowerSupply shows ok in show environment but fails in show module.

Connectrix: IP_FCMAC_CNT_STATS_ERRORS_RX_BAD_WORDS_FROM_DECODER on admin down port

Dell Connectrix MDS Cisco remediation is available for CLI vulnerability that could be exploited by malicious users to compromise the affected system.

"Interface fcx/y Slowport Count = ## Credit Delay" messages are streaming in "show logging" log from 16 Gbps switches.

PLATFORM-2-PS_UNSUPPORTED: Detected an unsupported power supply

Dell Connectrix (Cisco) MDS DCNM remediation is available for an NX-OS vulnerability that may be exploited by malicious users to compromise the affected system.

Dell Connectrix (Cisco) remediation is available for multiple Spring vulnerabilities that may be exploited by malicious users to compromise the affected system.

Dell Connectrix Cisco MDS 9000 Switches remediation is available for the Cisco Discovery Protocol service of Cisco NX-OS Software that may allow an unauthenticated, adjacent attacker to cause the service to restart, resulting in a denial of service (DoS) condition.

Dell Connectrix Cisco MDS 9000 Switches remediation is available for NX-OS Software that may be exploited by malicious users to compromise the affected system.

Connectrix MDS 9700 series director: Several ports on module DS-X9448-768K9 are stuck in hwfaliure state with error-id 0xcce03600 logged

When performing Connectrix MDS upgrade, the "install all" command returns the message "Pre-upgrade check failed. "Return code -1."

SCG, Base64 encoding, Cisco, ESRS script, password Base64 Encoding

When third party security software run on MDS switches, they can report that MDS switches are accepting the TLS1.0 connections.

Customer noted dead paths on Windows hosts, and Devloss on Linux hosts following an NX-OS upgrade to version 9.4(2a).

Affected products after NX OS 9.4.2a upgrade: Cisco MDS 9000 NX-OS and SAN-OS Software, Cisco MDS 9100 Series Multilayer Fabric Switches, Cisco MDS 9200 Series Multiservice Switches, Cisco MDS 9300 Series Multilayer Fabric Switches, Cisco MDS 9500 Series Multilayer Directors, Cisco MDS 9700 Series Multilayer Directors

How to perform NX-OS upgrade on the MDS switches

This issue can be triggered only if, while lower-numbered slot supervisor is in ha-standby state, it is pulled out of the chassis without issuing the command `out-of-service module x`.

This vulnerability is deducted without any Qualys ID (QID) or CVE identifier with description Weak TLS or SSL key exchange vulnerability.

On a Connectrix MDS switch running at NX-OS 9.4.2(a), the "show tech-support details" generation completes partially on the switch.

This article explains how to configure TACACS on a Connectrix MDS switch.

Cisco MDS 9700 This issue is due to Ethernet Out of Band Channel (EOBC) is used for connectivity between supervisors (Active and Standby) and linecards. There is a heartbeat mechanism to monitor the state of the line card from both the supervisors. If the Line card CPU is not responding the expected action from the High availability policy is to reset the line card to recover it. This is mostly due to the hardware issues in the line card CPU. FC module f32mac hap reset with error SYSMGR-SLOT2-2-SERVICE_CRASHED: Service "f32mac" (PID 1515) has not caught signal 6

How to configure call home email alerts into a readable format on an MDS switch.

Domain IDs uniquely identify a switch in a Virtual Storage Area Network (VSAN). A switch may have different domain IDs in different VSANs. The domain ID is part of the overall Fibre Channel (FC) ID. The configured domain ID can be preferred or static. By default, the configured domain ID is 0 (zero) and the configured type is preferred. Domain IDs can range from 1 to 239. The 0 (zero) value can be configured only if you use the preferred option.

CallHome process causing unavailability in show CallHome, show running-config, or copy run start.

F16_PLDA_RXBUF_MERR error on a single port ASIC results in a complete module reload.

SnakeLoobpack passed incorrect port range to module warning when SnakeLoopback could not identify faulty device.