Removal
Stand
Identify the stand highlighted in blue.
Press and hold down on the tab that secures the stand to the display assembly base.
Lift the stand off the display assembly base.
Identify the stand location highlighted in blue.
Align the stand to the slot with the display assembly base.
Slide the stand into place into the slot on the display assembly base.
Back Cover
Identify the back cover highlighted in blue.
Using your palm, gently pry the back cover from the top corners of the display assembly base.
Lift the back cover off the display assembly base.
Identify the back cover location highlighted in blue.
Align the slots on the back cover with the slots on the computer.
Slide to install back cover and press along the side to snap the back cover into place.
I/O Cover
Identify the I/O cover highlighted in blue.
Remove the screws that secure the I/O cover to the display assembly base.
Using a pry tool, pry open the corners and bottom of the I/O cover.
Pry open at the corner and lift the I/O cover off the display assembly base.
Identify the I/O cover location highlighted in blue.
Place the I/O cover on the display assembly base and align with screw holes.
Install the screws that secure the I/O cover to the display assembly base.
System Board Shield
Identify the system board shield highlighted in blue.
Remove the screws that secure the system board shield to the display assembly base.
Lift the system board shield off the display assembly base.
Identify the system board shield location highlighted in blue.
Place the system board shield on the display assembly base and align with screw holes.
Install the screws that secure the system board shield to the display assembly base.
Memory Module
Identify the memory module highlighted in blue.
Using your fingertips, carefully spread apart the securing clips on each end until the memory module pops up.
Hold the edges and carefully lift the memory module up from connector on the system board.
Identify the memory module location highlighted in blue.
Align the notch on the memory module with the tab on the slot and slide the memory module into the slot at an angle.
Press the memory module down until it clicks into place.
Wireless Card
Identify the wireless module (WLAN) highlighted in blue.
Remove the screw that secures the wireless card bracket.
Slide and remove the bracket to access the WLAN cables.
Disconnect the antenna cables (black and white cables) from the WLAN.
Slide and remove the WLAN card from the connector.
Identify the wireless module (WLAN) location highlighted in blue.
Insert the WLAN into the connector on the system board.
Connect the black cable to the auxiliary (black triangle).
Connect the white cable to the main (white triangle).
Slide and install the bracket to secure the antenna cables.
Install the screw that secures the wireless card bracket.
Solid State Drive (SSD) 2230
Identify the solid state drive (SSD) highlighted in blue.
Remove the screw that secures the SSD to the system board.
Slide and lift the solid state drive (SSD) from the system board.
Identify the solid state drive location highlighted in blue.
Align the notch on the SSD with the tab on the slot and slide the SSD into the slot.
Install the screw to secure the SSD to the system board.
Coin Cell Battery
Identify the coin cell battery highlighted in blue.
Push the release lever on the coin cell battery socket to release it from the socket.
Lift the coin cell battery from the socket.
Identify the coin cell battery location highlighted in blue.
Insert the coin cell battery into the socket with the positive side (+) label facing up.
Snap the battery in the socket.
Heat Sink
System Board
Identify the system board highlighted in blue.
Disconnect the backlight and fan cables from the system board.
Disconnect the speaker and microphone module cables from the system board.
Lift the latch and disconnect the media card reader, power button board and display cables from the system board.
Remove the screws that secure the system board to the display assembly base.
Remove the solid state drive screw mount that secures the system board to the display assembly base.
Lift the system board off the display assembly base.
Install
System Board
Identify the system board location highlighted in blue.
Install the system board on the display assembly base and align with the screw holes.
Install the screws that secure the system board to the display assembly base.
Install the solid state drive screw mount that secures the system board to the display assembly base.
Connect the media card reader, power button board and display cables on the system board. Close the latch to secure.
Connect the backlight and fan cables on the system board.
Connect the speaker and microphone module cables on the system board.
Heat Sink
Coin Cell Battery
Identify the heatsink location highlighted in blue.
Apply a pea sized amount of thermal material as shown.
Install the heatsink into the slot on the system board.
Tighten the captive screws that secure the heat sink. Tighten in order. Do not over tighten.
Solid State Drive (SSD) 2230
Identify the heatsink location highlighted in blue.
Apply a pea sized amount of thermal material as shown.
Install the heatsink into the slot on the system board.
Tighten the captive screws that secure the heat sink. Tighten in order. Do not over tighten.
Wireless Card
Identify the heatsink location highlighted in blue.
Apply a pea sized amount of thermal material as shown.
Install the heatsink into the slot on the system board.
Tighten the captive screws that secure the heat sink. Tighten in order. Do not over tighten.
Memory Module
Identify the heatsink location highlighted in blue.
Apply a pea sized amount of thermal material as shown.
Install the heatsink into the slot on the system board.
Tighten the captive screws that secure the heat sink. Tighten in order. Do not over tighten.
System Board Shield
Identify the heatsink location highlighted in blue.
Apply a pea sized amount of thermal material as shown.
Install the heatsink into the slot on the system board.
Tighten the captive screws that secure the heat sink. Tighten in order. Do not over tighten.
I/O Cover
Identify the heatsink location highlighted in blue.
Apply a pea sized amount of thermal material as shown.
Install the heatsink into the slot on the system board.
Tighten the captive screws that secure the heat sink. Tighten in order. Do not over tighten.
Back Cover
Identify the heatsink location highlighted in blue.
Apply a pea sized amount of thermal material as shown.
Install the heatsink into the slot on the system board.
Tighten the captive screws that secure the heat sink. Tighten in order. Do not over tighten.
Stand
Identify the heatsink location highlighted in blue.
Apply a pea sized amount of thermal material as shown.
Install the heatsink into the slot on the system board.
Tighten the captive screws that secure the heat sink. Tighten in order. Do not over tighten.