Recovering from unresponsive storage array condition
A storage array can have an Unresponsive status for several
reasons. Use the procedure in this topic to determine a possible cause
and solution. The MD Storage Manager can take up to five minutes to
detect that a storage array has become unresponsive or becomes responsive
again. Before completing this procedure, make sure that you wait for
some time before you decide that the storage array is still unresponsive.
To recover
from an unresponsive storage array:
Check the Tree View in the EMW to see if all storage arrays
are unresponsive.
If any storage arrays are unresponsive, check the storage
management station network connection to make sure that it can reach
the network.
Ensure that the RAID controller modules are installed and
that there is power to the storage array.
If there a problem with the storage array, then correct the
problem.
Perform one of these actions, depending on how your storage
array is managed:
Out-of-band managed storage array—Go to step 6.
In-band managed storage array—Go to step 12.
For an out-of-band managed storage array, ensure that the
RAID controller modules are network accessible by using the ping command
to make sure that the RAID controller module can be reached. Type
one of these commands, and press <Enter>.
ping <host-name>
ping <RAID controller module-IP-addres>
If the verification is successful, see step 8, if not,
see step 9.
Remove the storage array with the Unresponsive status from
the EMW, and select Add Storage Array to add
the storage array again.
If the storage array does not return to Optimal status,
check the Ethernet cables to make sure that there is no visible damage
and that they are securely connected.
Make sure the appropriate network configuration tasks have
been performed. For example, make sure that IP addresses have been
assigned to each RAID controller module.
If there is a cable or network accessibility problem, see
step 20, if not step 12.
For an in-band managed storage array, make sure that the
host is network accessible by using the ping command
to verify that the host can be reached. Type one of these commands,
and press <Enter>.
ping <host-name>
ping <RAID controller module-IP-addres>
If the verification is successful, see step 14, if not,
step 15.
Remove the host with the Unresponsive status from the EMW,
and select Add Storage Array to add the host
again.
If the host does not return to Optimal status, go to step
16.
Ensure that the host is turned on and operational and that
the host adapters have been installed.
Check all external cables and switches or hubs to make
sure that no visible damage exists and that they are securely connected.
Make sure the Host Context Agent software is installed
and running.
If you started the host system before you were connected to
the RAID controller module in the storage array, the Host Context
Agent software will not be able to detect the RAID controller modules.
If so, make sure that the connections are secure, and
restart the Host Context Agent software.
If you have recently replaced or added the RAID controller
module, restart the Host Context Agent software so that the new RAID
controller module is recognized.
If the problem still exists, make the appropriate host
modifications, check with other administrators to see if a firmware
upgrade was performed on the RAID controller module from another storage
management station.
If a firmware upgrade was performed, the EMW on your management
station may not be able to locate the new AMW software needed to manage
the storage array with the new version of the firmware.
If the problem persists contact your Technical Support
representative.
Determine if there is an excessive amount of network traffic
to one or more RAID controller modules.
This problem is self-correcting because the EMW software periodically
retries to establish communication with the RAID controller modules
in the storage array. If the storage array was unresponsive and a
subsequent attempt to connect to the storage array succeeds, the storage
array becomes responsive.
For an out-of-band managed storage array,
determine if management operations are taking place on the storage
array from other storage management stations. A RAID controller module-determined
limit exists to the number of Transmission Control Protocol/Internet
Protocol (TCP/IP) connections that can be made to the RAID controller
module before it stops responding to subsequent connection attempts.
The type of management operations being performed and the number of
management sessions taking place together determine the number of
TCP/IP connections made to a RAID controller module. This problem
is self-correcting because, after some TCP/IP connections terminate,
the RAID controller module then becomes responsive to other connection
attempts.
If the storage array is still unresponsive, a problem may
exist with the RAID controller modules. Contact your Technical Support
representative.
Data is not available for the Topic
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\