Creating SNMP alert notifications—originating from the storage
array
NOTE: The availability of SNMP alerts originating from the
storage array varies depending on your RAID controller module model.
The MD storage management software can notify
you when the status of a storage array or one of its components changes.
This is called an alert notification. You can receive alert notifications
by three different methods: email, SNMP traps originating from the
storage management station where the event monitor is installed, and
SNMP traps originating from the storage array (if available). This
topic describes how to create SNMP traps originating from the storage
array.
To configure an SNMP alert notification originating from
the storage array, you specify the community name and the trap destination.
The community name is a string that identifies a known set of network
management stations and is set by the network administrator. The trap
destination is the IP address or the host name of a computer running
an SNMP service. At a minimum, the trap destination is the network
management station. Keep these guidelines in mind when configuring
SNMP alert notifications:
Host destinations for SNMP traps must be running an SNMP service
so that the trap information can be processed.
Global settings are not required for the SNMP trap messages. Trap
messages sent to a network management station or other SNMP servers
are standard network traffic, and a system administrator or network
administrator handles the security issues.
In the Enterprise Management Window (EMW), select the Devices tab.
Right-click the storage array that you want to send alerts,
and then select Configure Alerts.
Select the SNMP - Storage Array Origin Trap tab.
The Configure Alerts dialog is displayed.
The Configured communities table is populated with the currently configured
community names and the Configured SNMP addresses table is populated
with the currently configured trap destinations.
NOTE: If the SNMP - Storage Array Origin Trap tab does not appear,
this feature might not be available on your RAID controller module
model.
(Optional) If you want to define the SNMP MIB-II variables
that are specific to the storage array, perform this step.
You only need to enter this information once for each storage
array. An icon is displayed next to the Configure SNMP MIB-II
Variables button if any of the variables are currently
set. The storage array returns this information in response to GetRequests.
The Name field populates the variable sysName.
The Location field populates the variable sysLocation.
The Contact field populates the variable sysContact.
Click Configure SNMP MIB-II Variables.
In the Name text box, the Location text box, and the Contact text box, enter the desired information.
You can enter only printable ASCII characters. Each text string
can contain a maximum of 255 characters.
Click OK.
In the Trap Destination text field,
enter the trap destination, and click Add.
You can enter a host name, an IPv4 address, or an IPv6 address. If you enter a host name, it is converted into an IP address for
display in the Configured SNMP addresses table. A storage array can
have a maximum of 10 trap destinations.
NOTE: This field is disabled
if no community names are configured.
If you have more than one community name configured, in
the Community Name column of the Configured
SNMP addresses table, select a community name from the drop-down list.
Do you want to send a trap when an authentication failure
occurs on the storage array?
Yes – Select the check box in the Send Authentication Failure Trap column of the Configured
SNMP addresses table. Selecting the check box sends an authentication
failure trap to the trap destination whenever an SNMP request is rejected
because of an unrecognized community name.
No – Clear the check box in the Send Authentication Failure Trap column of the Configured
SNMP addresses table.
(Optional) To verify that an SNMP alert is configured correctly,
you can send a test message. In the Configured SNMP addresses area,
select the SNMP destination that you want to test, and click Test.
A test message is sent to the SNMP address. A dialog is displayed with
the results of the validation and any errors. The Test button is disabled
if you have not selected a community name.
Click OK.
An alert icon is displayed next to each node in the Tree view
for which an alert is set.
Data is not available for the Topic
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\