- Notes, cautions, and warnings
- Dell PowerEdge M630p overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- Viewing System BIOS
- System BIOS Settings details
- Boot Settings
- Network Settings
- System Security
- System Information
- Memory Settings
- Processor Settings
- SATA Settings
- Integrated Devices
- Serial Communication
- System Profile Settings
- Miscellaneous Settings
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing server module components
- Safety instructions
- Recommended tools
- Installing and removing a server module
- System cover
- Inside the server module
- System memory
- Cooling shroud
- Processor blank and DIMM blank
- PCIe mezzanine cards
- Internal dual SD module (optional)
- rSPI card (optional)
- SD vFlash card
- Network Daughter Card
- Processors
- Hard drives or SSDs
- Hard drive or SSD bay numbering
- Hard drive or SSD installation guidelines
- Removing a hard drive or SSD
- Installing a hard drive or SSD
- Removing a hard drive or SSD blank
- Installing a hard drive or SSD blank
- Shutdown procedure for servicing a hard drive
- Configuring the boot drive
- Removing a 2.5-inch hard drive or SSD from a 2.5-inch hard drive or SSD carrier
- Installing a 2.5-inch hard drive or SSD in a 2.5-inch hard-drive or SSD carrier
- Removing a 1.8-inch SSD from a 1.8-inch SSD carrier
- Installing a 1.8-inch SSD in a 1.8-inch SSD carrier
- Removing the hard drive or SSD cage
- Installing the hard drive or SSD cage
- Hard drive or SSD backplane
- Storage controller card
- System board
- System battery
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Getting help
Velkommen
Dell-websteder
Dell-websteder
Velkommen hos Dell
Min konto
- Afgiv ordrer hurtigt og nemt
- Se ordrer og spor status for din forsendelse
- Opret og få adgang til en liste med dine produkter
- Administrer dine Dell EMC-websteder, -produkter og -kontaktpersoner på produktniveau ved hjælp af Company Administration (Virksomhedsadministration).
Dell PowerEdge M630 Systems (VRTX Enclosure) Owner's Manual
Installing the optional IDSDM card
Prerequisites
CAUTION: Many
repairs may only be done by a certified service technician. You should
only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service
and support team. Damage due to servicing that is not authorized by
Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
NOTE: You must remove the
IDSDM card to replace a faulty IDSDM card or service other components
inside the system.
Follow the safety guidelines listed in safety instructions section.
Keep the Phillips #2 screwdriver ready.
Remove the SD card.
Remove the IDSDM card.
CAUTION: To prevent damage to the IDSDM card, you must hold the card only
by its edges.
Steps
- Align the following:
- The slot on the card edge with the projection tabs on the PCIe mezzanine card support.
- The two screw holes on the IDSDM card with the standoffs on the system board.
- The hole on the SD card slot bracket with the screw hole on the IDSDM card.
- Install the two screws to secure the SD card
slot bracket and IDSDM card to the system board.
Figure 1. Installing the optional IDSDM card 
- IDSDM card
- screw (2)
- SD card slot bracket
- PCIe mezzanine card support bracket
- IDSDM card connector on the system board
- standoff (2)
Next steps
If applicable, install the SD card(s) and the internal USB key.
Follow the procedure listed in the After working inside your system section.
Angiv vurderinger (1-5 stjerner).
Angiv vurderinger (1-5 stjerner).
Angiv vurderinger (1-5 stjerner).
Angiv, om artiklen var nyttig eller ej.
Kommentarer må ikke indeholde følgende specialtegn: <>()\