- Notes, Cautions, and Warnings
- Introduction
- AMP Event Messages
- ASR Event Messages
- BAR Event Messages
- BAT Event Messages
- BIOS Event Messages
- BOOT Event Messages
- CBL Event Messages
- CMC Event Messages
- CPU Event Messages
- CPUA Event Messages
- CTL Event Messages
- DH Event Messages
- DIAG Event Messages
- DIS Event Messages
- DKM Event Messages
- ECM Event Messages
- ENC Event Messages
- EPP Event Messages
- FAN Event Messages
- FC Event Messages
- FCD Event Messages
- FLDC Event Messages
- FSD Event Messages
- HWC Event Messages
- IOID Event Messages
- IOV Event Messages
- IPA Event Messages
- ISM Event Messages
- JCP Event Messages
- LC Event Messages
- LIC Event Messages
- LNK Event Messages
- LOG Event Messages
- MEM Event Messages
- NIC Event Messages
- OSD Event Messages
- OSE Event Messages
- PCI Event Messages
- PDR Event Messages
- PFM Event Messages
- POW Event Messages
- PR Event Messages
- PST Event Messages
- PSU Event Messages
- PSUA Event Messages
- PWR Event Messages
- RAC Event Messages
- RDU Event Messages
- RED Event Messages
- RFL Event Messages
- RFLA Event Messages
- RFM Event Messages
- RRDU Event Messages
- RSI Event Messages
- SEC Event Messages
- SEL Event Messages
- SSD Event Messages
- STOR Event Messages
- SUP Event Messages
- SWC Event Messages
- SWU Event Messages
- SYS Event Messages
- TMP Event Messages
- TMPS Event Messages
- TST Event Messages
- UEFI Event Messages
- USR Event Messages
- VDR Event Messages
- VF Event Messages
- VFL Event Messages
- VFLA Event Messages
- VLT Event Messages
- VME Event Messages
- VRM Event Messages
Event and Error Message Reference Guide for 13th Generation Dell PowerEdge ServersVersion 1.2
OSD Event Messages
OSD062
- Message
- The process of installing an operating system or hypervisor is started and is in progress.
- Detailed Description
- The process of installing an operating system or hypervisor is started and is in progress.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
OSD063
- Message
- The process of installing an operating system or hypervisor is successfully completed.
- Detailed Description
- The process of installing an operating system or hypervisor is successfully completed.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
OSD064
- Message
- The process of installing an operating system or hypervisor is abruptly stopped either by the user or the installation infrastructure.
- Detailed Description
- The process of installing an operating system or hypervisor is abruptly stopped either by the user or the installation infrastructure.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
OSD065
- Message
- Operating System/Hypervisor Installation did not complete successfully.
- Detailed Description
- The Operating System/Hypervisor installation did not complete successfully. The system may be unable to boot into the operating system/hypervisor because of the incomplete installation.
- Recommended Response Action
- Check the installation logs of operating system or hypervisor, resolve any issues identifed, and then retry the operation. If the issue persists, contact your service provider.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 1 (Critical)
OSD10
- Message
- Installation not supported for the selected operating system.
- Detailed Description
- Installation for the selected operating system is not supported. Make sure that the correct operating system name was entered.
- Recommended Response Action
- Recheck the operating system name with the output of GetDriverPackInfo().
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD11
- Message
- Driver Pack does not have drivers for the selected operating system.
- Detailed Description
- Lifecycle Controller does not have any drivers for the selected operating system. The operating system installation uses the native drivers present on the operating system media.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
OSD12
- Message
- Cannot create the USB device needed to copy drivers for the selected operating system.
- Detailed Description
- iDRAC was unable to create and expose the drivers as a USB device for the OS installation to proceed.
- Recommended Response Action
- 1) Rerun the command. 2) Reset iDRAC and rerun the command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
OSD13
- Message
- Cannot mount the USB device needed to copy drivers for the selected operating system.
- Detailed Description
- iDRAC was unable to mount the drivers as a USB device for the OS installation to proceed.
- Recommended Response Action
- 1) Rerun the command. 2) Reset iDRAC and rerun the command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
OSD14
- Message
- Unable to expose the USB device that contains the operating system drivers to host system.
- Detailed Description
- iDRAC was unable to expose the drivers as a USB device for the OS installation to proceed.
- Recommended Response Action
- 1) Rerun the command. 2) Reset iDRAC and rerun the command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
OSD15
- Message
- Mount network share failed - incorrect username or password.
- Detailed Description
- Unable to mount the network share using the credentials specified in the command because either the username or password is incorrect.
- Recommended Response Action
- Rerun the command with the correct username and password.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD16
- Message
- Mount network share failed - incorrect IP address or share name.
- Detailed Description
- Unable to mount the network share using the parameters specified in the command because either the IP address or share name is incorrect.
- Recommended Response Action
- Rerun the command with the correct IP address and share name.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD17
- Message
- Exposing ISO image as internal device to the server failed.
- Detailed Description
- Unable to expose the ISO image as an internal CD device to the host system because the ISO file is no longer present, network errors are preventing access to the ISO file, or iDRAC may not be responsive.
- Recommended Response Action
- 1) Rerun the command. 2) Reset iDRAC and rerun the command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
OSD18
- Message
- Unable to locate the ISO image on the network share point.
- Detailed Description
- Unable to find the ISO file specified in the network share. Make sure that the correct ISO file path was entered into the command and that all other user credentials are correct.
- Recommended Response Action
- Rerun the command with the correct ISO file path.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD19
- Message
- The fork() command for a child process to perform the task failed.
- Detailed Description
- Failed to execute fork() system call to perform the task in a child process. iDRAC may be unresponsive.
- Recommended Response Action
- Reset iDRAC and rerun the command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
OSD20
- Message
- Unable to get size or label from Driver Pack for selected operating system.
- Detailed Description
- Unable to get the size or label for selected operating system from the Driver Pack present in Lifecycle Controller. The driver pack may be corrupt.
- Recommended Response Action
- Update the Driver Pack using USC or DUP and rerun the command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD21
- Message
- Unable to boot to ISO image.
- Detailed Description
- Booting to ISO has failed. Either BIOS was unable to boot to the ISO image or the provider did not get a response in 5 minutes from BIOS on successful boot to ISO image.
- Recommended Response Action
- 1) Make sure that a POST error did not result in user interaction (Press F1 to continue or F2 to run BIOS setup). 2) Reset iDRAC and rerun the command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD22
- Message
- Unable to detach ISO image from the host.
- Detailed Description
- Unable to detach ISO image from the host because either the image is already detached, or iDRAC may not be operating normally.
- Recommended Response Action
- 1) Rerun the command. 2) Reset iDRAC
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
OSD23
- Message
- Unable to continue with DetachISOImage - another command is in the process of exposing the ISO Image and booting to it.
- Detailed Description
- Cannot continue with DetachISOImage because another command is in the process of exposing the ISO image and booting to it.
- Recommended Response Action
- See the ConcreteJob status to make sure that the current running process is complete and then run DetachISOImage.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
OSD24
- Message
- Unable to continue with DetachDrivers - UnPackAndAttach is in progress.
- Detailed Description
- Unable to continue with DetachDrivers - UnPackAndAttach is in progress.
- Recommended Response Action
- Wait until UnpackAndAttach finishes and then run DetachDrivers. This can take more than 5 minutes.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
OSD25
- Message
- Unable to detach USB device containing operating system drivers.
- Detailed Description
- Detaching the USB device (that contains drivers for the operating system installation) from the host has failed. The device may be detached, or iDRAC may not be operating normally.
- Recommended Response Action
- Reset iDRAC to detach this device automatically.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
OSD26
- Message
- Unable to continue with BootToPXE - another command is running.
- Detailed Description
- Unable to continue with BootToPXE command because another process is using Lifecycle Controller.
- Recommended Response Action
- See ConcreteJob status to make sure that the running process is complete, and then run BootToPXE.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD27
- Message
- Copying drivers for selected operating system failed.
- Detailed Description
- Copying drivers for selected operating system failed. The Driver Pack may be unusable.
- Recommended Response Action
- Update the Driver Pack using USC or DUP and then rerun the command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
OSD28
- Message
- Hash verification on the ISO image failed.
- Detailed Description
- Hash verification on the ISO image has failed. The hash value specified in the command is either incorrect or the ISO image has been changed.
- Recommended Response Action
- 1) Verify that the hash value specified in the command is correct. 2) Make sure that the ISO has not been changed 3) Replace the ISO image on the share and rerun the command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD29
- Message
- Driver Pack configuration file not found in Lifecycle Controller. The Driver Pack might be corrupt.
- Detailed Description
- Driver Pack configuration file not found in Lifecycle Controller. Driver Pack may be unusable.
- Recommended Response Action
- Update the Driver Pack using USC or DUP and then rerun the command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD3
- Message
- Lifecycle Controller is being used by another process.
- Detailed Description
- Lifecycle Controller is currently locked by another process. Make sure that the process completes before attempting to run another command.
- Recommended Response Action
- 1) After two minutes, rerun the command. 2) Make sure that USC or DUP is not currently running on the server. 3) Reset iDRAC and rerun the command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD30
- Message
- Invalid value for ExposeDuration - must be 60 - 65535 seconds
- Detailed Description
- The value specified for ExposeDuration is out of range. It must be between 60 and 65535 seconds
- Recommended Response Action
- Rerun the command with a ExposeDuration value between 60 and 65535 seconds.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD31
- Message
- Copying operating system drivers to network share failed
- Detailed Description
- Copying drivers for the selected operating system to network share failed. The share may be read-only or the Driver Pack present in Lifecycle Controller may be unusable.
- Recommended Response Action
- 1) Make sure that the network share has write permission. 2) Update the Driver Pack using USC or DUP and then rerun the command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD32
- Message
- Unable to detach ISO image from the system.
- Detailed Description
- Cannot continue with DetachISOImage because the system does not have an attached ISO image.
- Recommended Response Action
- The call to DetachISOImage is unnecessary since the ISO image is not currently attached.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
OSD33
- Message
- Installed BIOS version does not support this method.
- Detailed Description
- The system has an older version of BIOS that does not support this method. Install the latest version of BIOS to use this method.
- Recommended Response Action
- Update the BIOS to version 1.2 or later and then rerun the command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD34
- Message
- Unable to continue with BootToPXE - ISO image is attached to the system.
- Detailed Description
- Unable to continue with BootToPXE command because the system has an ISO image attached. Detach the ISO image before continuing with BootToPXE.
- Recommended Response Action
- Run the DetachISOImage command and then run BootToPXE.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
OSD35
- Message
- Lifecycle Controller is not enabled.
- Detailed Description
- Lifecycle Controller is disabled on the system, so none of the remote operating system deployment commands will work. Make sure Lifecycle Controller is enabled before running any command.
- Recommended Response Action
- Reboot the system and enable System Services by pressing CTRL+E option when prompted to do so in the POST. This launches the iDRAC configuration utility where Lifecycle Controller can be enabled.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
OSD36
- Message
- Boot to ISO Image has been cancelled by using CTRL+E option on the server.
- Detailed Description
- User has cancelled system services by using the CTRL+E option (iDRAC configuration utility) during POST. This action cancels the WSMAN request to boot to ISO.
- Recommended Response Action
- To resolve the issue rerun the command. Do not cancel system services using CTRL+E during POST when system is rebooting to the ISO.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD37
- Message
- ISO image size too large.
- Detailed Description
- ISO Image size is bigger than the available size in VFlash.
- Recommended Response Action
- 1) Use a smaller size ISO Image. 2) Format the VFlash using the iDRAC GUI, RACADM, or iDRAC configuration utility and then retry this command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD38
- Message
- Copying the ISO image from the network failed.
- Detailed Description
- There was an error while copying the ISO from the network share.
- Recommended Response Action
- 1) Make sure the network connection is functional. 2) Make sure the Dell VFlash doesnt have hardware issues by accessing it through the iDRAC GUI.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD39
- Message
- Unable to find the VFlash.
- Detailed Description
- Unable to get VFlash information from internal instrumentation.
- Recommended Response Action
- 1) Make sure the Dell VFlash is seated correctly. 2) Make sure a Dell licensed VFlash card is inserted 3) Make sure the Dell VFlash doesnt have any hardware issues by accessing it through the iDRAC GUI.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD4
- Message
- Cannot access Lifecycle Controller Driver Pack partition.
- Detailed Description
- Driver Pack partition in Lifecycle Controller is not accessible. The Lifecycle Controller or the iDRAC might be unresponsive.
- Recommended Response Action
- Reset the iDRAC and rerun the command. If the command fails again, check if the iDRAC is functional and accessible on the system.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
OSD41
- Message
- ISO Image not found on VFlash.
- Detailed Description
- VFlash does not contain the ISO Image because either the image was deleted, or it was never copied.
- Recommended Response Action
- Download the ISO Image to the VFlash again using the DownloadISOToVFlash method.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD42
- Message
- Downloading ISO File to VFlash failed.
- Detailed Description
- There was an error while copying the ISO image from the network share to the VFlash.
- Recommended Response Action
- 1) Make sure the network connection is working. 2) Make sure the Dell VFlash doesnt have any hardware issues by accessing it through the iDRAC GUI.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD44
- Message
- Unable to detach ISO image on VFlash.
- Detailed Description
- The ISO on VFlash is not currently attached, so the DetachISOFromVFlash command could not be executed.
- Recommended Response Action
- Since the ISO image is not attached, the detachISOFromVflash command does not have to be run.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
OSD45
- Message
- Cannot delete ISO image from VFlash.
- Detailed Description
- The ISO Image present in VFlash is attached to the host system. The ISO Image cannot be deleted from VFlash.
- Recommended Response Action
- Execute DetachISOFromVFlash() before running DeleteISOFromVFlash()
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD46
- Message
- VFlash in use.
- Detailed Description
- Another process (iDRAC GUI /racadm/iDRAC configuration utility) is currently accessing VFlash.
- Recommended Response Action
- Wait until the access to VFlash is relinquished and then retry this command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
OSD47
- Message
- Inaccessible network share.
- Detailed Description
- Unable to access the network share using the credentials specified or the firewall might be enabled and is preventing access to the share.
- Recommended Response Action
- Make sure that the firewall is disabled, and that the credentials (username, password) are correct.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD48
- Message
- ISO Images of more than 4GB not supported.
- Detailed Description
- ISO Images of more than 4GB are not supported and cannot be copied to VFlash.
- Recommended Response Action
- Use an ISO that is smaller than 4GB.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD49
- Message
- Disable RIPS mode to access VFlash.
- Detailed Description
- VFlash cannot be accessed because RIPS mode is enabled.
- Recommended Response Action
- Disable the RIPS mode from BIOS or from the iDRAC GUI, and then continue executing the method.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD5
- Message
- Lifecycle Controller Driver Pack not found.
- Detailed Description
- A Driver Pack was not found on the Lifecycle Controller.
- Recommended Response Action
- Update the Driver Pack using USC or DUP and then run the command again.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD50
- Message
- Lifecycle Controller is in field service mode.
- Detailed Description
- Lifecycle Controller is in field service mode and needs to be updated before proceeding further.
- Recommended Response Action
- Install the Lifecycle Controller field services package using the iDRAC GUI.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD51
- Message
- Reboot the system to run pending System Services Tasks.
- Detailed Description
- There are pending System Services tasks on the host system that are preventing the execution of this method.
- Recommended Response Action
- Reboot the host system. The system will automatically enter System Services and complete the pending tasks.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
OSD54
- Message
- vFlash already has 16 partitions
- Detailed Description
- vFlash allows only 16 partitions to be created
- Recommended Response Action
- Make sure that there are less than 16 partitions before creating another partition on vFlash.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
OSD55
- Message
- ISO Image is attached to host
- Detailed Description
- Cannot attach the ISO image since it is already attached to the host.
- Recommended Response Action
- ISO Image is already attached to the host server. Detach the ISO and then rerun the command
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
OSD56
- Message
- An ISO is already connected using Remote File Share (RFS).
- Detailed Description
- An ISO is already connected using Remote File Share (RFS). The connection might have been initiated from iDRAC GUI, racadm, or Remote Services API.
- Recommended Response Action
- Disconnect the Remote File Share (RFS) using iDRAC GUI, racadm, or Remote Services API and then retry the operation to connect the ISO again.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
OSD57
- Message
- Remote File Share (RFS) is in Auto-Attach mode.
- Detailed Description
- Remote File Share (RFS) is currently configured to be in auto-attach mode. For Web services to attach an ISO, RFS should be changed to attach mode.
- Recommended Response Action
- Change the Remote File Share (RFS) mode to Attach using iDRAC GUI or Remote Services API and retry.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD58
- Message
- Unable to connect an ISO using Remote File Share (RFS).
- Detailed Description
- The connect ISO operation using Remote File Share (RFS) did not complete successfully.
- Recommended Response Action
- Verify all the parameters are correct. If the problem persists. then reset iDRAC and retry the operation.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD59
- Message
- Unable to disconnect from ISO using Remote File Share (RFS).
- Detailed Description
- Disconnecting ISO using Remote File Share (RFS) operation did not complete successfully.
- Recommended Response Action
- Reset iDRAC and retry the operation.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD60
- Message
- Unable to connect to ISO using Remote File Share (RFS).
- Detailed Description
- Connecting ISO using Remote File Share (RFS) was unsuccessful.
- Recommended Response Action
- Verify ISO is connected using Remote File Share (RFS) and retry the operation.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
OSD61
- Message
- IP Address format is invalid.
- Detailed Description
- The IP Address format is invalid and cannot be validated. The specified IP address may not be a valid IPv4 or IPv6 address.
- Recommended Response Action
- Verify the IP address format and retry the operation.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
OSD7
- Message
- Unable to retrieve Lifecycle Controller handle.
- Detailed Description
- Unable to connect to Lifecycle Controller because of an existing open connection or an internal error.
- Recommended Response Action
- Reset iDRAC, and rerun the command to correct the problem.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
OSD8
- Message
- Setting Boot to PXE through IPMI failed.
- Detailed Description
- The BIOS boot order set to PXE using a standard IPMI command has failed.
- Recommended Response Action
- 1) Check BIOS PXE settings. 2) Rerun the command. 3) Reset iDRAC and rerun the command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
OSD9
- Message
- Failed to reboot the system using an IPMI command.
- Detailed Description
- Resetting the targeted server using the standard IPMI command has failed.
- Recommended Response Action
- 1) Rerun the command. 2) Reset iDRAC and rerun the command.
- Category
- Configuration (OSD = OS Deployment)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\