Skip to main content

Event and Error Message Reference Guide for 13th Generation Dell PowerEdge ServersVersion 1.2

PDF

POW Event Messages

POW000

Message: Power on permission error, chassis infrastructure not ready.
Detailed Description: Host failed to power up bacause chassis infrastructure is not ready. This messages has been replaced by Message ID PWR2250
Recommended Response Action: Check status of chassis infrastructure.
Category: Audit (POW = Power Usage)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC			✔	✔	✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*		✔
CMC

POW001

Message: Power on permission error, chassis cover open.
Detailed Description: Host failed to power up because chassis cover is open.This messages has been replaced by Message ID PWR2251
Recommended Response Action: Check chassis cover.
Category: Audit (POW = Power Usage)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC			✔	✔	✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*		✔
CMC

POW002

Message: Power on permission error, unknown component installed in Fabric1/Fabric2.
Detailed Description: Host failed to power up because unsupported components installed in Fabric1/fabric2.This messages has been replaced by Message ID PWR2252
Recommended Response Action: Check for unsupported components installed in Fabric1/Fabric2.
Category: Audit (POW = Power Usage)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC			✔	✔	✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*		✔
CMC

POW003

Message: Power on permission error, no PCI/Mezz card installed in Fabric1/Fabric2
Detailed Description: Host failed to power up because PCI/Mezz cards not installed in Fabric1/Fabric2.This messages has been replaced by Message ID PWR2253
Recommended Response Action: Install PCI/Mezz card in Fabric1/Fabric2.
Category: Audit (POW = Power Usage)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC				✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

POW004

Message: Power on permission error, unacknowledge use of 110V.
Detailed Description: Host failed to power up because of unacknowledged use of 110V. This messages has been replaced by Message ID PWR2254
Recommended Response Action: Check for unacknowledged use of 110V.
Category: Audit (POW = Power Usage)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC				✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

POW005

Message: Power on permission error, CMC is in MPCM mode.
Detailed Description: Host failed to power up bacause CMC MPCM mode is enabled. This messages has been replaced by Message ID PWR2255
Recommended Response Action: Disable MPCM mode to power up.
Category: Audit (POW = Power Usage)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC				✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC