Gå til hovedindhold
Log af

Velkommen hos Dell

Min konto
  • Afgiv ordrer hurtigt og nemt
  • Se ordrer og spor status for din forsendelse
  • Opret og få adgang til en liste med dine produkter
  • Administrer dine Dell EMC-websteder, -produkter og -kontaktpersoner på produktniveau ved hjælp af Company Administration (Virksomhedsadministration).
Log på Opret en konto Log på Premier Log på Partnerprogram
Kontakt os

Dine Dell.com-kurve

Artikelnummer: 000132465

Windows 10 install with NVMe SSD and SATA drives

Oversigt: This article provides the information about "Installing Windows 10 on computers that contain both NVMe SSD and SATA storage options present".

Denne artikel er muligvis automatisk blevet oversat. Hvis du gerne vil give feedback om dens kvalitet, så giv os besked ved hjælp af formularen nederst på denne side.

Artikelindhold

Symptomer

The current Dell Windows 10 media will fail to install on computers that are configured with both Serial ATA (SATA) Hard Disk Drives (hard drive)s and Non-Volatile Memory (NVMe) high-performance Peripheral Component Interconnect Express (PCIe) Solid-State Drives (SSDs).

NVMe SSD drives are available on select Dell computers such as:

  • OptiPlex 7440, 7040, 5040
  • Latitude E7470, E7270, E5270, E5470, E5570
  • Precision 3510, 5510, 7510, 7710
  • XPS 9350, 9550, 9250
  • Alienware X51, 15 R2, 13 R2
NOTE: As previously mentioned this issue and workaround is only valid for computers that have NVMe SSD AND SATA Storage Drives installed.
If the computer only has a SATA Drive present, turning off the device will result in a failure to detect any storage devices.

Årsag

There is an incompatibility between the Current Windows 10 recovery environment (WinRE) storage drivers and the NVMe high-performance SSD drivers when there is a combination of SSDs and HDDs on the same computer.

Løsning

Workaround

The current workaround is to disable all the SATA Storage device (HDD/SSD) controllers in the computer Basic Input/Output System (BIOS) before performing the Windows 10 install to the NVMe SSD from Dell media.

After disabling the SATA Storage Device, you also have to ensure that the BIOS is set up correctly by following these Steps:

  1. Enter the BIOS by pressing F2 multiple times while the Dell Logo is shown.
  2. Go to Boot Sequence and set Boot List Option to UEFI
  3. Go to SATA Operation and choose AHCI
  4. In Advanced Boot Option, you click Enable Legacy Option ROMs
  5. Set Secure Boot to Disable

Once the Windows installation is completed, the SATA Storage Device controllers can be reenabled without any issues and both the NVMe drive and one or more SATA drives will function normally. No further changes are necessary.

Dell Engineering has addressed this issue, and a fix was incorporated into the latest Dell Windows 10 media release. Recovery media options are available at Dell Windows Backup Media and Recovery Options.

Flere oplysninger

SLN301036_en_US__1Windows
More information and support for your Windows operating systems can be found on our Windows Support webpage.

Recommended Articles

Here are some recommended articles related to this topic that might be of interest to you.

Out of Warranty support Out of warranty? No problem. Browse to the Dell.com/support website and enter your Dell Service Tag and view our offers.

NOTE: Offers are only available for US, Canada, UK, France, Germany, China, and Japan personal computer customers. Server and Storage not applicable.

Egenskaber for artikel

Sidste udgivelsesdato

20 dec. 2023

Version

9

Artikeltype

Solution

Tilbage til toppen