Dell Networking OS10 GRE 配置简介
Summary: 通用路由封装 （GRE） 是一种 IP 封装协议，用于在网络上的两个路由器之间建立虚拟点对点连接。它通常用于在不同站点之间建立 RIP 和 OSPF 等路由协议的隧道。GRE 在征求意见稿 （RFC 2784.
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Instructions
涵盖的关键议题
GRE 隧道的配置：
- 在两个路由器之间配置 GRE 隧道，以直接发送和接收 GRE 数据包。
- 配置涉及设置隧道接口、指定隧道模式、源和目标。
限制和局限性：
- 最多支持 100 个隧道
- 底层和覆盖路径上不支持 IPv6。
- 与 GRE 隧道配合使用时，某些接口和 IP 地址具有限制。
Tunnel Keepalive 设置：
- 配置 keepalive 设置，以使用 Internet 控制消息协议 （ICMP） 回显和回复数据包监视隧道端点的可访问性。
等价多路径 （ECMP） 叠加层和底层：
- ECMP 负载共享，用于在可用路由之间分配流量
- 覆盖和底层 ECMP 路由支持的组合。
命令和示例：
- 有关配置 GRE 隧道、keepalive 设置和 ECMP 路由的详细命令语法和示例
配置错误可能导致的问题
隧道摆动：
- 不正确的 keepalive 设置可能会导致隧道频繁地上下移动，从而导致不稳定。
MTU 不匹配：
- 通过具有不同 MTU 设置的路径建立 GRE 隧道可能会导致数据包碎片或丢失。
路由环路：
- 错误配置的路由可能会导致环路，从而导致过多的流量和潜在的网络中断。
最佳做法
一致的 MTU 设置：
- 确保 GRE 隧道中的 MTU 设置一致，以避免碎片化。
正确的 Keepalive 配置：
- 配置 keepalive 设置以监控隧道运行状况并避免不必要的摆动。
清除文档：
- 维护隧道配置和关联路由的清晰文档，以防止错误配置。
GRE 隧道的用例。
连接远程站点：
- GRE 隧道可以通过 Internet 连接远程站点，从而实现安全高效的通信。
隧道传输非 IP 流量：
- GRE 可以封装非 IP 流量，使其适用于各种网络协议。
负载均衡：
- 将 ECMP 与 GRE 隧道结合使用可以跨多个路径分配流量负载，从而提高网络性能。
网络拓扑示例
设想一个具有两个远程站点（站点 A 和站点 B）的网络，它们通过 Internet 连接。每个站点都有一个路由器，并在它们之间配置了 GRE 隧道。
拓扑如下所示：
站点 A （10.10.10.0/24） ---- OS10-1 ---- Internet ---- OS10-2 ----站点 B （10.20.10.0/24）
OS10(config)# interface tunnel 10 OS10(conf-if-tunnel-10)# <165>1 2022-11-11T17:55:16.614662+00:00 OS10 dn_alm 731 - - Node.1-Unit.1:PRI [event], Dell (OS10) %IFM_ASTATE_UP: Interface admin state up :tunnel10 OS10(conf-if-tunnel-10)# ip vrf forwarding red % Error: Interface tunnel10, Tunnel mode is mandatory config and must exist for other tunnel configs. OS10(conf-if-tunnel-10)# mode gre-ipv4 OS10(conf-if-tunnel-10)# ip vrf forwarding red OS10(conf-if-tunnel-10)# ip address 120.1.1.1/24 OS10(conf-if-tunnel-10)# <165>1 2022-11-11T17:55:31.454972+00:00 OS10 dn_alm 731 - - Node.1-Unit.1:PRI [event], Dell (OS10) %IP_ADDRESS_ADD: IP Address add is successful. IP 120.1.1.1/24 in VRF:red added successfully OS10(conf-if-tunnel-10)# tunnel destination 16.16.16.16 OS10(conf-if-tunnel-10)# tunnel source loopback10 OS10(conf-if-tunnel-10)# <165>1 2022-11-11T17:56:17.197783+00:00 OS10 dn_alm 731 - - Node.1-Unit.1:PRI [event], Dell (OS10) %IFM_OSTATE_UP: Interface operational state is up :tunnel10
OS10(conf-if-tunnel-10)# show configuration ! interface tunnel10 mode gre-ipv4 no shutdown ip vrf forwarding red ip address 120.1.1.1/24 tunnel destination 10.10.10.10 tunnel source loopback10 keepalive down-timer 10 keepalive enable keepalive probe-interval 6 keepalive up-timer 12
| 底层 ECMP 路由 | 覆盖 ECMP 路由 | 支持 |
|---|---|---|
| 静态 | 静态 | 是的 |
| 静态 | OSPF的 | 是的 |
| 静态 | 边界网关协议 | 是的 |
| OSPF的 | 静态 | 是的 |
| OSPF的 | OSPF的 | 否 |
| OSPF的 | 边界网关协议 | 是的 |
| 边界网关协议 | 静态 | 是的 |
| 边界网关协议 | OSPF的 | 是的 |
| 边界网关协议 | 边界网关协议 | 否 |
OS10(config)# hardware overlay-ecmp-profile mode balanced-overlay-ecmp OS10(config)# <165>1 2022-10-11T10:25:26.474891+00:00 AG1-9978 dn_alm 717 - - Node.1- Unit.1:PRI [event], Dell (OS10) %VXLAN_OVERLAY_ECMP_PROFILE_MODIFIED: VxLAN Overlay ECMP: Configuration is modified, Save and Reload the device for the profile to be effect
OS10# show running-configuration interface tunnel 21 ! interface tunnel21 mode gre-ipv4 no shutdown ip address 10.10.10.2/24 tunnel destination 5.5.5.5 tunnel source loopback3 OS10# show running-configuration interface tunnel 22 ! interface tunnel22 mode gre-ipv4 no shutdown ip address 10.10.10.3/24 tunnel destination 6.6.6.6 tunnel source loopback4 OS10# show running-configuration interface tunnel 23 ! interface tunnel23 mode gre-ipv4 no shutdown ip address 10.10.10.4/24 tunnel destination 7.7.7.7 tunnel source loopback5 OS10# show running-configuration interface tunnel 24 ! interface tunnel24 mode gre-ipv4 no shutdown ip address 10.10.10.5/24 tunnel destination 8.8.8.8 tunnel source loopback6 OS10# show running-configuration route ! ip route 77.1.1.0/24 100.1.1.2 ip route 77.1.1.0/24 10.10.10.2 ip route 77.1.1.0/24 10.10.10.3 ip route 77.1.1.0/24 10.10.10.4 ip route 77.1.1.0/24 10.10.10.5 OS10# show ip route 10.1.1.0/24 Routing entry for 77.1.1.0/24 Known via static Distance 1, Metric 0 Last update 08:57:53 Routing descriptors Blocks: via 100.1.1.2 tunnel10 via 10.10.10.2 tunnel21 via 10.10.10.3 tunnel22 via 10.10.10.4 tunnel23 via 10.10.10.5 tunnel24
OS10# show ip route 67.67.67.0/24 Routing entry for 67.67.67.0/24 Known via ospf, type Distance 110, Metric 21 Last update 09:35:46 Routing descriptors Blocks: via 10.1.1.2 ethernet1/1/25:1 via 12.1.1.2 ethernet1/1/25:2 via 23.2.2.2 vlan2 via 23.2.3.2 vlan3 via 23.2.4.2 vlan4 via 23.2.5.2 vlan5 via 23.2.6.2 vlan6 via 23.2.7.2 vlan7 via 23.2.8.2 vlan8 via 23.2.9.2 vlan9 OS10# show ip route 68.68.68.0/24 Routing entry for 68.68.68.0/24 Known via ospf, type Distance 110, Metric 21 Last update 09:36:35 Routing descriptors Blocks: via 10.1.1.2 ethernet1/1/25:1 via 12.1.1.2 ethernet1/1/25:2 via 23.2.2.2 vlan2 via 23.2.3.2 vlan3 via 23.2.4.2 vlan4 via 23.2.5.2 vlan5 via 23.2.6.2 vlan6 OS10# show running-configuration interface vlan 2 ! interface vlan2 no shutdown ip address 23.2.2.1/24 ip ospf 1 area 0.0.0.0 OS10# show running-configuration interface vlan 3 ! interface vlan3 no shutdown ip address 23.2.3.1/24 ip ospf 1 area 0.0.0.0 OS10# show running-configuration interface vlan 4 ! interface vlan4 no shutdown ip address 23.2.4.1/24 ip ospf 1 area 0.0.0.0 OS10# show running-configuration interface tunnel 21 ! interface tunnel21 mode gre-ipv4 no shutdown ip address 131.131.131.1/24 tunnel destination 67.67.67.67 tunnel source loopback3 OS10# show running-configuration interface tunnel 22 ! interface tunnel22 mode gre-ipv4 no shutdown ip address 132.132.132.1/24 tunnel destination 68.68.68.68 tunnel source loopback4
-
示例
OS10# clear counters interface tunnel 10
-
示例
OS10(config)# interface tunnel 10
-
示例
OS10(conf-if-tunnel-40)# ip address 10.1.1.1/24
-
示例
OS10(conf)# ip route 1.1.1.0/24 interface tunnel 10 OS10(conf)# ip route 2.2.2.0/24 3.3.3.3 interface tunnel 10
-
示例
OS10(conf-if-tunnel-4)# ip vrf forwarding Vrf_red
-
示例
OS10(conf-if-tunnel-1)# keepalive down-timer 10
-
示例
OS10(conf-if-tunnel-1)# keepalive enable
-
示例
OS10(conf-if-tunnel-1)# keepalive probe-interval 10
-
示例
OS10(conf-if-tunnel-1)# keepalive up-timer 10
-
示例
OS10(conf-if-tunnel-1)# mode gre-ipv4
-
示例
OS10(conf-if-tunnel-40)# tunnel destination 10.10.10.10
-
示例
OS10(conf-if-tunnel-4)# tunnel source vlan 10
-
示例
OS10(conf-if-tunnel-1)# tunnel ttl 220
-
示例
OS10# show interface tunnel 10 Tunnel 10 is up, line protocol is up Hardware is Tunnel Tunnel mode GREv4 Tunnel source IP 2.2.2.2, Tunnel source Intf loopback1 Tunnel destination 7.7.7.7 Tunnel TTL 255 Tunnel keepalive enabled Keepalive probe interval 10, Up timer 5, Down timer 5 Interface index is 45 Internet address is 10.1.1.1/24 Mode of IPv4 Address Assignment: MANUAL Interface IPv6 oper status: Enabled ARP type: ARPA, ARP Timeout: 60 Last clearing of "show interface" counters: 00:11:22 Queuing strategy: fifo Input statistics: 0 packets, octets Output statistics: 0 packets, octets Time since last interface status change: 00:27:11
-
示例
OS10# show running-configuration interface tunnel ! interface tunnel10 no shutdown mode gre-ipv4 ip address 100.1.1.1/24 tunnel destination 3.3.3.3 tunnel source 1.1.1.1 ! interface tunnel20 no shutdown mode gre-ipv4 ip address 101.1.1.1/24 tunnel destination 5.5.5.5 tunnel source 6.6.6.6 OS10# show running-configuration interface tunnel 10 ! interface tunnel10 no shutdown mode gre-ipv4 ip address 100.1.1.1/24 tunnel destination 3.3.3.3 tunnel source 1.1.1.1
示例
OS10# show tunnel Name Mode Source-IP Destination-IP SrcIntf TTL VRF Status Protocol ================================================================================================= Tunnel 1 GREv4 1.1.1.1 6.6.6.6 Loopback 2 255 default up up Tunnel 2 GREv4 2.2.2.2 7.7.7.7 Loopback 123 255 default up up Tunnel 3 GREv4 3.3.3.3 8.8.8.8 Loopback 100 255 default up up OS10# show tunnel 10 Name Mode Source-IP Destination-IP SrcIntf TTL VRF Status Protocol ================================================================================================= Tunnel 10 GREv4 1.1.1.1 7.6.6.6 Loopback 2 255 default up up
-
示例
OS10# show ip int gig 1/3 GigabitEthernet 1/3 is up, line protocol is down Internet address is 10.11.0.1/24 Broadcast address is 10.11.0.255 Address determined by user input IP MTU is 1500 bytes Helper address is 192.168.0.1 192.168.0.2 Directed broadcast forwarding is disabled
-
示例
OS10# show ip route Codes: C - connected S - static B - BGP, IN - internal BGP, EX - external BGP, EV - EVPN BGP O - OSPF, IA - OSPF inter area, N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2, E1 - OSPF external type 1, E2 - OSPF external type 2, * - candidate default, + - summary route, > - non-active route Gateway of last resort is not set Destination Gateway Dist/Metric Last Change -------------------------------------------------------------------- C 1.1.1.0/24 via 1.1.1.1 ethernet1/1/1:1 0/0 01:32:53 C 10.1.1.0/24 via 100.1.1.1 loopback1 0/0 00:00:06 C 2.2.2.0/24 via 2.1.1.1.1 Tunnel 1 0/0 00:00:15 OS10# show ip route static Codes: C - connected S - static B - BGP, IN - internal BGP, EX - external BGP, EV - EVPN BGP O - OSPF, IA - OSPF inter area, N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2, E1 - OSPF external type 1, E2 - OSPF external type 2, * - candidate default, + - summary route, > - non-active route Gateway of last resort is not set Destination Gateway Dist/Metric Last Change ---------------------------------------------------------------------- C 1.1.1.0/24 via 1.1.1.1 ethernet1/1/1:1 0/0 01:32:53 C 10.1.1.0/24 via 100.1.1.1 loopback1 0/0 00:00:06 S 80.1.10.0/24 via 100.1.1.1 tunnel10 1/0 00:02:33
OS10# show ip ospf interface tunnel 10 tunnel10 is up, line protocol is up Internet Address 100.1.1.1/24, Area 0.0.0.0 Process ID 1, Router ID 1.1.1.1, Network Type broadcast, Cost: 1 Transmit Delay is 1 sec, State DR, Priority 1 Designated Router (ID) 1.1.1.1 (local), Interface address 100.1.1.1 Backup Designated router (ID) , Interface address 0.0.0.0 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Neighbor Count is 0, Adjacent neighbor count is 0 OS10# show ip ospf 1 interface tunnel 10 tunnel10 is up, line protocol is up Internet Address 100.1.1.1/24, Area 0.0.0.0 Process ID 1, Router ID 1.1.1.1, Network Type broadcast, Cost: 1 Transmit Delay is 1 sec, State DR, Priority 1 Designated Router (ID) 1.1.1.1 (local), Interface address 100.1.1.1 Backup Designated router (ID) , Interface address 0.0.0.0 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Neighbor Count is 0, Adjacent neighbor count is 0
-
示例
OS10# show ip ospf 1 statistics interface tunnel 10 Interface tunnel10 Receive Statistics rx-invalid 0 rx-invalid-bytes 0 rx-hello 0 rx-hello-bytes 0 rx-db-des 0 rx-db-des-bytes 0 rx-ls-req 0 rx-ls-req-bytes 0 rx-ls-upd 0 rx-ls-upd-bytes 0 rx-ls-ack 0 rx-ls-ack-bytes 0 Transmit Statistics tx-failed 0 tx-failed-bytes 0 tx-hello 52 tx-hello-bytes 3328 tx-db-des 0 tx-db-des-bytes 0 tx-ls-req 0 tx-ls-req-bytes 0 tx-ls-upd 0 tx-ls-upd-bytes 0 tx-ls-ack 0 tx-ls-ack-bytes 0 Error packets (Receive statistics) bad-src 0 dupe-id 0 hello-err 0 mtu-mismatch 0 nbr-ignored 0 wrong-proto 0 resource-err 0 bad-lsa-len 0 lsa-bad-type 0 lsa-bad-len 0 lsa-bad-cksum 0 auth-fail 0 netmask-mismatch 0 hello-tmr-mismatch 0 dead-ivlmismatch 0 options-mismatch 0 nbr-admin-down 0 own-hellodrop 0 self-orig 0 wrong-length 0 checksumerror 0 version-mismatch 0 area-mismatch 0
Additional Information
Affected Products
SmartFabric OS10 SoftwareArticle Properties
Article Number: 000228691
Article Type: How To
Last Modified: 03 Oct 2025
Version: 2
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.