PowerStore: Management Network Reconfiguration does not validate NTP server provided as FQDN when changing IP protocol version
概要: Management network IP protocol version change from IPv4 to IPv6 or from IPv6 to IPv4 using Management Network Reconfiguration (MNR) does not validate NTP server provided as Fully Qualified Domain Name. ...
この記事は次に適用されます：
この記事は次には適用されません：
この記事は、特定の製品に関連付けられていません。
すべての製品パージョンがこの記事に記載されているわけではありません。
現象
The Management Network Reconfiguration IP protocol version change (IPv4 > IPv6 or IPv6 > IPv4) operation does not accept NTP server value configured as FQDN with the following error message:
"The following NTP server addresses are invalid: 'NTP_SERVER_FQDN' (0xE0E400701002)"
"The following NTP server addresses are invalid: 'NTP_SERVER_FQDN' (0xE0E400701002)"
原因
PowerStore supports changing management network IP protocol version from IPv4 to IPv6 and IPv6 to IPv4. This requires the change of configured environment services (NTP, DNS) to match the updated network.
Management Network Reconfiguration (MNR) wizard asks for new PowerStore addresses and for new addresses of network service. Multiple addresses can be provided for DNS and NTP for redundancy purposes.
If a user provides at least one FQDN for the NTP server, wizard does not validate the NTP server and gives an error of invalid NTP server:
"The following NTP server addresses are invalid: 'NTP_SERVER_FQDN' (0xE0E400701002)"
Figure 1: Management Network Reconfiguration wizard-Invalid NTP error
MNR wizard stops, newly provided settings are not applied, and management network is not reconfigured. The system is available with the old network settings.
Management Network Reconfiguration (MNR) wizard asks for new PowerStore addresses and for new addresses of network service. Multiple addresses can be provided for DNS and NTP for redundancy purposes.
If a user provides at least one FQDN for the NTP server, wizard does not validate the NTP server and gives an error of invalid NTP server:
"The following NTP server addresses are invalid: 'NTP_SERVER_FQDN' (0xE0E400701002)"
Figure 1: Management Network Reconfiguration wizard-Invalid NTP error
MNR wizard stops, newly provided settings are not applied, and management network is not reconfigured. The system is available with the old network settings.
解決方法
NTP server must be configured by specifying its IP address instead of a Fully Qualified Domain Name (FQDN).
Figure 2: NTP configured as FQDN
Figure 3: NTP configured with IP address
NTP validation should succeed now, and management network reconfiguration should finish. The system should be accessible at newly provided addresses.
* If Reconfigure Management Network wizard was closed, start it again and provide NTP server IP addresses (not FQDN) at Infrastructure Services step.
- If Reconfigure Management Network wizard is not closed (*), click Back button until the Infrastructure Services step.
Figure 2: NTP configured as FQDN
- Replace any provided NTP server FQDN values with corresponding IP addresses.
Figure 3: NTP configured with IP address
- Click Next and go through further steps until the end.
NTP validation should succeed now, and management network reconfiguration should finish. The system should be accessible at newly provided addresses.
* If Reconfigure Management Network wizard was closed, start it again and provide NTP server IP addresses (not FQDN) at Infrastructure Services step.
対象製品
PowerStore文書のプロパティ
文書番号: 000201823
文書の種類: Solution
最終更新: 13 6月 2025
バージョン: 4
質問に対する他のDellユーザーからの回答を見つける
サポート サービス
お使いのデバイスがサポート サービスの対象かどうかを確認してください。