Skip to main content
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Create and access a list of your products
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.

Dell PowerEdge FN I/O Module Configuration Guide 9.10(0.0)

PDF

Sample Configurations

Before you set up VRRP, review the following sample configurations.

VRRP for an IPv4 Configuration

The following configuration shows how to enable IPv4 VRRP. This example does not contain comprehensive directions and is intended to provide guidance for only a typical VRRP configuration. You can copy and paste from the example to your CLI. To support your own IP addresses, interfaces, names, and so on, be sure that you make the necessary changes. The VRRP topology was created using the CLI configuration shown in the following example.

Figure 1. VRRP for IPv4 Topology Illustration of VRRP for IPv4 topology.

Example of Configuring VRRP for IPv4

R2(conf)#int tengig 2/31
                                 R2(conf-if-te-2/31)#ip address 10.1.1.1/24
                                 R2(conf-if-te-2/31)#vrrp-group 99
                                 R2(conf-if-te-2/31-vrid-99)#priority 200
                                 R2(conf-if-te-2/31-vrid-99)#virtual 10.1.1.3
                                 R2(conf-if-te-2/31-vrid-99)#no shut
                                 R2(conf-if-te-2/31)#show conf
                                 !
                                 interface Tengigabitethernet 2/31
                                 ip address 10.1.1.1/24
                                 !
                                 vrrp-group 99
                                 priority 200
                                 virtual-address 10.1.1.3
                                 no shutdown
                                 R2(conf-if-te-2/31)#end
                                 R2#show vrrp
                                 ------------------
                                 Tengigabitethernet 2/31, VRID: 99, Net: 10.1.1.1
                                 State: Master, Priority: 200, Master: 10.1.1.1 (local)
                                 Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec
                                 Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 817, Gratuitous ARP sent: 1
                                 Virtual MAC address:
                                 00:00:5e:00:01:63
                                 Virtual IP address:
                                 10.1.1.3
                                 Authentication: (none)
                                 R2#
                                 Router 3
                                 R3(conf)#int tengig 3/21
                                 R3(conf-if-te-3/21)#ip address 10.1.1.2/24
                                 R3(conf-if-te-3/21)#vrrp-group 99
                                 R3(conf-if-te-3/21-vrid-99)#virtual 10.1.1.3
                                 R3(conf-if-te-3/21-vrid-99)#no shut
                                 R3(conf-if-te-3/21)#show conf
                                 !
                                 interface Tengigabitethernet 3/21
                                 ip address 10.1.1.2/24
                                 !
                                 vrrp-group 99
                                 virtual-address 10.1.1.3
                                 no shutdown
                                 R3(conf-if-te-3/21)#end
                                 R3#show vrrp
                                 ------------------
                                 Tengigabitethernet 3/21, VRID: 99, Net: 10.1.1.2
                                 State: Backup, Priority: 100, Master: 10.1.1.1
                                 Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec
                                 Adv rcvd: 698, Bad pkts rcvd: 0, Adv sent: 0, Gratuitous ARP sent: 0
                                 Virtual MAC address:
                                 00:00:5e:00:01:63
                                 Virtual IP address:
                                 10.1.1.3
                                 Authentication: (none)
                                 
                              

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\