Skip to main content
Sign Out

Welcome to Dell

My Account
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Create and access a list of your products
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.
Sign In Create an Account Premier Sign In Partner Program Sign In
Contact Us

Your Dell.com Baskets

Dell PowerEdge FN I/O Module Configuration Guide 9.10(0.0)

PDF

Display the Logging Buffer and the Logging Configuration

To display the current contents of the logging buffer and the logging settings for the system, use the show logging command in EXEC privilege mode. When RBAC is enabled, the security logs are filtered based on the user roles. Only the security administrator and the system administrator can view the security logs.

Example of the show logging Command 

Dell#show logging
                                 syslog logging: enabled
                                 Console logging: level Debugging
                                 Monitor logging: level Debugging
                                 Buffer logging: level Debugging, 40 Messages Logged, Size (40960 bytes)
                                 Trap logging: level Informational
                                 %IRC-6-IRC_COMMUP: Link to peer RPM is up
                                 %RAM-6-RAM_TASK: RPM1 is transitioning to Primary RPM.
                                 %RPM-2-MSG:CP1 %POLLMGR-2-MMC_STATE: External flash disk missing in 'slot0:'
                                 %CHMGR-5-CARDDETECTED: Line card 0 present
                                 %CHMGR-5-CARDDETECTED: Line card 2 present
                                 %CHMGR-5-CARDDETECTED: Line card 4 present
                                 %CHMGR-5-CARDDETECTED: Line card 5 present
                                 %CHMGR-5-CARDDETECTED: Line card 8 present
                                 %CHMGR-5-CARDDETECTED: Line card 10 present
                                 %CHMGR-5-CARDDETECTED: Line card 12 present
                                 %TSM-6-SFM_DISCOVERY: Found SFM 0
                                 %TSM-6-SFM_DISCOVERY: Found SFM 1
                                 %TSM-6-SFM_DISCOVERY: Found SFM 2
                                 %TSM-6-SFM_DISCOVERY: Found SFM 3
                                 %TSM-6-SFM_DISCOVERY: Found SFM 4
                                 %TSM-6-SFM_DISCOVERY: Found SFM 5
                                 %TSM-6-SFM_DISCOVERY: Found SFM 6
                                 %TSM-6-SFM_DISCOVERY: Found SFM 7
                                 %TSM-6-SFM_SWITCHFAB_STATE: Switch Fabric: UP
                                 %TSM-6-SFM_DISCOVERY: Found SFM 8
                                 %TSM-6-SFM_DISCOVERY: Found 9 SFMs
                                 %CHMGR-5-CHECKIN: Checkin from line card 5 (type EX1YB, 1 ports)
                                 %TSM-6-PORT_CONFIG: Port link status for LC 5 => portpipe 0: OK portpipe 1: N/A
                                 %CHMGR-5-LINECARDUP: Line card 5 is up
                                 %CHMGR-5-CHECKIN: Checkin from line card 12 (type S12YC12, 12 ports)
                                 %TSM-6-PORT_CONFIG: Port link status for LC 12 => portpipe 0: OK portpipe 1: N/A
                                 %CHMGR-5-LINECARDUP: Line card 12 is up
                                 %IFMGR-5-CSTATE_UP: changed interface Physical state to up: So 12/8
                                 %IFMGR-5-CSTATE_DN: changed interface Physical state to down: So 12/8

To view any changes made, use the show running-config logging command in EXEC privilege mode, as shown in the example for Configuring a UNIX Logging Facility Level.

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\