Dell PowerEdge M620 Systems Owner's Manual

System Error Messages

System messages appear on the monitor to notify you of a possible problem with the system. These messages refer to events recorded in the System Event Log (SEL). For information on the SEL and configuring system management settings, see the systems management software documentation.

Some messages are also displayed in abbreviated form on the system's LCD, if the system includes that feature.

NOTE: The LCD error messages listed here are displayed in the simple format. See Setup Menu to select the format in which the messages are displayed.

NOTE: If you receive a system message not listed here, check the documentation for the application that was running when the message was displayed or the operating system's documentation for an explanation of the message and recommended action.

NOTE: In some messages, a particular system component is identified by name (“<name>”), component number (“<number>”), or location (“bay”).

Error Code

Message Information

AMP0300

Message

The system board < name> current is less than the lower warning threshold.

Details

System board < name> current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0301

Message

The system board < name> current is less than the lower warning threshold.

LCD Message

System board < name> current is outside of range.

Details

System board < name> current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0302

Message

The system board < name> current is greater than the upper warning threshold.

Details

System board < name> current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0303

Message

The system board < name> current is greater than the upper critical threshold.

LCD Message

System board < name> current is outside of range.

Details

System board < name> current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0304

Message

The system board < name> current is outside of range.

LCD Message

System board < name> current is outside of range.

Details

System board < name> current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0306

Message

Disk drive bay < name> current is less than the lower warning threshold.

Details

Disk drive bay < name> current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0307

Message

Disk drive bay < name> current is less than the lower critical threshold.

LCD Message

Disk drive bay < name> current is outside of range.

Details

Disk drive bay < name> current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0308

Message

Disk drive bay < name> current is greater than the upper warning threshold.

Details

Disk drive bay < name> current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0309

Message

Disk drive bay < name> current is greater than the upper critical threshold.

LCD Message

Disk drive bay < name> current is outside of range.

Details

Disk drive bay < name> current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0310

Message

Disk drive bay < name> current is outside of range.

LCD Message

Disk drive bay < name> current is outside of range.

Details

Disk drive bay < name> current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0312

Message

System level current is less than the lower warning threshold.

Details

System level current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0313

Message

System level current is less than the lower warning threshold.

LCD Message

System level current is outside of range.

Details

System level current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0314

Message

System level current is greater than the upper warning threshold.

Details

System level current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0315

Message

System level current is greater than the upper critical threshold.

LCD Message

System level current is outside of range.

Details

System level current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0316

Message

System level current is outside of range.

LCD Message

System level current is outside of range.

Details

System level current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0318

Message

Chassis power level current is less than the lower warning threshold.

Details

Chassis power level current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0319

Message

Chassis power level current is less than the lower critical threshold

Details

Chassis power level current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0320

Message

Chassis power level current is greater than the upper warning threshold.

Details

Chassis power level current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0321

Message

Chassis power level current is greater than the upper critical threshold.

Details

Chassis power level current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

AMP0322

Message

Chassis power level current is outside of range.

Details

Chassis power level current is outside of the optimum range.

Action

Review system power policy.
Check system logs for power related failures.
Review system configuration changes.
If the issue persists, see Getting Help.

ASR0000

Message: The watchdog timer expired.
Details: The operating system or an application failed to communicate within the time-out period.
Action: Check the operating system, application, hardware, and system event log for exception events.

ASR0001

Message: The watchdog timer reset the system.
Details: The operating system or an application failed to communicate within the time-out period. The system was reset.
Action: Check the operating system, application, hardware, and system event log for exception events.

ASR0002

Message: The watchdog timer powered off the system.
Details: The operating system or an application failed to communicate within the time-out period. The system was shut down.
Action: Check the operating system, application, hardware, and system event log for exception events.

ASR0003

Message: The watchdog timer power cycled the system.
Details: The operating system or an application failed to communicate within the time-out period. The system was power-cycled.
Action: Check the operating system, application, hardware, and system event log for exception events.

ASR0008

Message: The watchdog timer interrupt was initiated.
Details: The operating system or an application failed to communicate within the time-out period. No action was taken.
Action: Check the operating system, application, hardware, and system event log for exception events.

ASR0100

Message: The BIOS watchdog timer reset the system.
Details: The operating system or an application failed to communicate within the time-out period. The system was reset.
Action: Check the operating system, application, hardware, and system event log for exception events.

ASR0101

Message: The OS watchdog timer reset the system.
Details: The operating system or an application failed to communicate within the time-out period. The system was reset.
Action: Check the operating system, application, hardware, and system event log for exception events.

ASR0102

Message: The OS watchdog timer shutdown the system.
Details: The operating system or an application failed to communicate within the time-out period. The system was shutdown.
Action: Check the operating system, application, hardware, and system event log for exception events.

ASR0103

Message: The OS watchdog timer powered down the system.
Details: The operating system or an application failed to communicate within the time-out period. The system was powered down.
Action: Check the operating system, application, hardware, and system event log for exception events.

ASR0104

Message: The OS watchdog timer power-cycled the system.
Details: The operating system or an application failed to communicate within the time-out period. The system was power-cycled.
Action: Check the operating system, application, hardware, and system event log for exception events.

ASR0105

Message: The operating system watchdog timer powered off the system.
Details: The operating system or an application failed to communicate within the time-out period. The system was powered off.
Action: Check the operating system, application, hardware, and system event log for exception events.

ASR0106

Message: The watchdog timer expired.
Details: The operating system or an application failed to communicate within the time-out period.
Action: Check the operating system, application, hardware, and system event log for exception events.

ASR0107

Message: The watchdog timer pre-timeout interrupt was initiated.
Details: The operating system or an application failed to communicate within the time-out period.
Action: Check the operating system, application, hardware, and system event log for exception events.

BAT0000

Message: The system board battery is low.
Details: The system board battery is either missing, bad, or unable to charge due to thermal issues.
Action: Check system fans. Replace the system board battery.

BAT0002

Message: The system board battery has failed.
LCD Message: The system board battery has failed. Check battery.
Details: The system board battery is either missing or bad.
Action: See Getting Help .

BAT0004

Message: The system board battery is absent.
LCD Message: The system board battery is absent. Check battery.
Action: Reinstall the system board battery.

BAT0005

Message: The storage battery is low.
Details: System has to remain powered on to charge the battery.
Action: Allow the battery to charge. If the issue persists, see Getting Help.

BAT0007

Message: The storage battery has failed.
LCD Message: The storage battery has failed. Check battery.
Details: Verify the cable connection between the storage battery and the controller.
Action: Verify the storage battery installation.

BAT0010

Message: The storage battery for disk drive bay < bay> is low.
Details: System has to remain powered on to charge the storage battery.
Action: Allow the storage battery to charge. If the issue persists, see Getting Help.

BAT0012

Message: The storage battery for disk drive bay < bay> has failed.
LCD Message: Battery for disk drive bay < bay> has failed. Check battery.
Details: Verify the cable connection between the storage battery and the controller.
Action: Verify the storage battery installation.

BAT0014

Message: The storage battery for disk drive bay < bay> is absent.
LCD Message: Battery for disk drive bay < bay> is absent. Check battery.
Details: Verify the cable connection between the storage battery and the controller.
Action: Verify the storage battery installation.

BAT0015

Message: The < name> battery is low.
Details: The low < name> battery may impact system performance negatively.
Action: Recharge the < name> battery if possible. If the problem continues replace the < name> battery.

BAT0017

Message: The < name> battery has failed.
LCD Message: The < name> battery has failed. Check battery.
Details: The < name> battery is either missing, bad, or unable to charge due to thermal issues.
Action: Check system fans. Replace the < name> battery.

BAT0019

Message: The < name> battery is absent.
LCD Message: The < name> battery is absent. Check battery.
Details: The failed or missing < name> battery may reduce system performance.
Action: Check system fans. Replace the < name> battery.

CBL0006

Message: Multiple storage controllers are incorrectly connected to the same backplane < Bay ID>.
Details: Unsupported backplane configuration.
Action: Check backplane configuration. Reconnect cable. If the issue persists, see Getting Help.

CPU0000

Message: CPU < number> has an internal error (IERR).
LCD Message: CPU < number> has an internal error (IERR).
Details: System event log and OS logs may indicate that the exception is external to the processor.
Action: Review System Event Log and Operating System Logs. If the issue persists, see Getting Help.

CPU0001

Message: CPU < number> has a thermal trip (over-temperature) event.
LCD Message: CPU < number> has a thermal trip. Check CPU heat sink.
Details: The processor temperature increased beyond the operational range.
Action: Review logs for fan failures, replace failed fans. If no fan failures are detected, check inlet temperature (if available) and reinstall processor heat-sink.

CPU0002

Message

CPU < number> has failed the built-in self-test (BIST).

Action

Turn system off and remove input power for one minute. Reapply input power and turn system on.
Make sure the processor is seated correctly.
If the issue persists, see Getting Help.

CPU0003

Message

CPU < number> is stuck in POST.

Action

Turn system off and remove input power for one minute. Reapply input power and turn system on.
Reduce system configuration to minimum memory and remove all PCI devices. If system completes POST, update system BIOS. reinstall memory and PCI one component at a time to meet the original configuration.
If the issue persists, see Getting Help.

CPU0004

Message

CPU < number> failed to initialize.

Action

Turn system off and remove input power for one minute. Reapply input power and turn system on.
Make sure the processor is seated correctly.
If the issue persists, see Getting Help.

CPU0005

Message: CPU < number> configuration is unsupported.
LCD Message: CPU < number> configuration is unsupported. Check CPU or BIOS revision.
Details: System is unable to boot or may run in a degraded state.
Action: Review the technical specifcations for supported processor types.

CPU0006

Message

Unrecoverable CPU complex error detected on CPU < number>.

Details

System is unable to boot or may run in a degraded state.

Action

Turn system off and remove input power for one minute. Reapply input power and turn system on.
Make sure the processor is seated correctly.
If the issue persists, see Getting Help.

CPU0008

Message: CPU < number> is disabled.
Details: System is unable to boot or may run in a degraded state.
Action: If unexpected, check presence, and system setup (BIOS) configuration.

CPU0010

Message: CPU < number> is throttled.
Details: The CPU is throttled due to thermal or power conditions.
Action: Review system logs for power or thermal exceptions.

CPU0023

Message: CPU < number> is absent.
LCD Message: CPU < number> is absent. Check CPU.
Action: Verify processor installation. If present, re-seat the processor.

CPU0100

Message: CPU < number> temperature is less than the lower warning threshold.
Details: System performance may be degraded.
Action: Check system operating environment.

CPU0101

Message: CPU < number> temperature is less than the lower critical threshold.
LCD Message: CPU < number> temperature is outside of range.
Details: System performance may be degraded.
Action: Check system operating environment, fans, and heat-sinks.

CPU0102

Message: CPU < number> temperature is greater than the upper warning threshold.
Details: System performance may be degraded.
Action: Check system operating environment, fans, and heat-sinks.

CPU0103

Message: CPU < number> temperature is greater than the upper critical threshold.
LCD Message: CPU < number> temperature is outside of range. Check fans.
Details: System performance may be degraded.
Action: Check system operating environment, fans, and heat-sinks.

CPU0104

Message: CPU < number> temperature is outside of range.
LCD Message: CPU < number> temperature is outside of range. Check fans.
Details: System performance may be degraded.
Action: Check system operating environment, fans, and heat-sinks.

CPU0200

Message

CPU < number> < name> voltage is less than the lower warning threshold.

Details

Low voltages may be the result of a problem with the voltage regulator or a problem with the processor. The low voltage may cause the processor to fail to operate.

Action

Turn system off and remove input power for one minute.
Reapply input power and turn system on.
Ensure the processor is seated correctly.
If the issue persists, see Getting Help.

CPU0201

Message

CPU < number> < name> voltage is less than the lower critical threshold.

LCD Message

CPU < number> < name> voltage is outside of range. Re-seat CPU.

Details

Low voltages may be the result of a problem with the voltage regulator or a problem with the processor. When the critical threshold is crossed, the processor will fail to operate. The system may power down.

Action

Turn system off and remove input power for one minute.
Reapply input power and turn system on.
Ensure the processor is seated correctly.
If the issue persists, see Getting Help.

CPU0202

Message

CPU < number> < name> voltage is greater than the upper warning threshold.

Details

High voltages may be the result of problem with the voltage regulator or a problem with the processor. Elevated voltages may result in damage to the processor or other electronic components in side the system.

Action

Turn system off and remove input power for one minute.
Reapply input power and turn system on.
Ensure the processor is seated correctly.
If the issue persists, see Getting Help.

CPU0203

Message

CPU < number> < name> voltage is greater than the upper critical threshold.

LCD Message

CPU < number> < name> voltage is outside of range. Re-seat CPU.

Details

High voltages may be the result of problem with the voltage regulator or a problem with the processor. Elevated voltages may result in damage to the processor or other system electrical components. The system may power down.

Action

Turn system off and remove input power for one minute.
Reapply input power and turn system on.
Ensure the processor is seated correctly.
If the issue persists, see Getting Help.

CPU0204

Message

CPU < number> < name> voltage is outside of range.

LCD Message

CPU < number> < name> voltage is outside of range. Re-seat CPU.

Details

Voltages outside the allowable range may damage electrical components or may cause the system to shutdown.

Action

Turn system off and remove input power for one minute.
Ensure the processor is seated correctly.
Reapply input power and turn system on.
If the issue persists, see Getting Help.

CPU0700

Message

CPU < number> initialization error detected.

LCD Message

CPU < number> initialization error detected. Power cycle system.

Details

System BIOS was unable to initialize the processor.

Action

Turn system off and remove input power for one minute.
Ensure the processor is seated correctly.
Reapply input power and turn system on.
If the issue persists, see Getting Help.

CPU0701

Message

CPU < number> protocol error detected.

LCD Message

CPU < number> protocol error detected. Power cycle system.

Details

System event log and operating system logs may indicate that the exception is external to the processor.

Action

Check system and operating system logs for exceptions. If no exceptions are found, continue.
Turn system off and remove input power for one minute.
Ensure the processor is seated correctly.
Reapply input power and turn system on.
If the issue persists, see Getting Help.

CPU0702

Message

CPU bus parity error detected.

LCD Message

CPU bus parity error detected. Power cycle system.

Details

System event log and operating system logs may indicate that the exception is external to the processor.

Action

Check system and operating system logs for exceptions. If no exceptions are found, continue.
Turn system off and remove input power for one minute.
Ensure the processor is seated correctly.
Reapply input power and turn system on.
If the issue persists, see Getting Help.

CPU0703

Message

CPU bus initialization error detected.

LCD Message

CPU bus initialization error detected. Power cycle system.

Details

System event log and operating system logs may indicate that the exception is external to the processor.

Action

Check system and operating system logs for exceptions. If no exceptions are found, continue.
Turn system off and remove input power for one minute.
Ensure the processor is seated correctly.
Reapply input power and turn system on.
If the issue persists, see Getting Help.

CPU0704

Message

CPU < number> machine check error detected.

LCD Message

CPU < number> machine check error detected. Power cycle system.

Details

System event log and operating system logs may indicate that the exception is external to the processor.

Action

Check system and operating system logs for exceptions. If no exceptions are found, continue.
Turn system off and remove input power for one minute.
Ensure the processor is seated correctly.
Reapply input power and turn system on.
If the issue persists, see Getting Help.

CPU0801

Message

CPU < number> voltage regulator module failed.

LCD Message

CPU < number> voltage regulator module failed. Re-seat module.

Details

System performance may be degraded or the system may fail to operate.

Action

Turn system off and remove input power for one minute.
Reapply input power and turn system on.
Ensure the processor is seated correctly.
If the issue persists, see Getting Help.

CPU0802

Message

A predictive failure detected on CPU < number> voltage regulator module.

Details

System performance may be degraded or the system may fail to operate.

Action

Turn system off and remove input power for one minute.
Reapply input power and turn system on.
Ensure the processor is seated correctly.
If the issue persists, see Getting Help.

CPU0803

Message

The power input for CPU < number> voltage regulator module is lost.

LCD Message

Lost power input for CPU < number>voltage regulator module. Re-seat module.

Details

System performance may be degraded or the system may fail to operate.

Action

Turn system off and remove input power for one minute.
Reapply input power and turn system on.
Ensure the processor is seated correctly.
If the issue persists, see Getting Help.

CPU0804

Message

The power input for CPU < number> voltage regulator module is outside of range.

LCD Message

The power input for CPU < number> voltage regulator module is outside of range. Re-seat module.

Details

System performance may be degraded or the system may fail to operate.

Action

Turn system off and remove input power for one minute.
Reapply input power and turn system on.
Ensure the processor is seated correctly.
If the issue persists, see Getting Help.

CPU0805

Message

The power input for CPU < number> voltage regulator module is outside of range, but it is attached to the system.

Details

System performance may be degraded or the system may fail to operate.

Action

Turn system off and remove input power for one minute.
Reapply input power and turn system on.
Ensure the processor is seated correctly.
If the issue persists, see Getting Help.

CPU0806

Message: CPU < number> voltage regulator module is incorrectly configured.
LCD Message: CPU < number> voltage regulator module incorrectly configured. Check configuration.
Details: System performance may be degraded or the system may fail to operate.
Action: Review this manual for proper configuration and installation procedures.

CPU0816

Message: CPU < number> voltage regulator module is absent.
LCD Message: CPU < number> voltage regulator module absent. Check module.
Details: System performance may be degraded or the system may fail to operate.
Action: If removal was unintended, check presence and reinstall.

HWC1001

Message: The < name> is absent.
LCD Message: The < name> is absent. Check hardware.
Details: The absent device may be necessary for proper operation. System functionality may be degraded.
Action: Reinstall or reconnect the hardware.

HWC1002

Message: The < name> is disabled.
Action: If device disabled unexpectedly, re-enable device.

HWC1005

Message: The storage adapter is absent.
LCD Message: The storage adapter is absent. Check hardware.
Details: The storage adapter may be necessary for proper operation. System functionality may be degraded.
Action: Install storage adapter.

HWC1006

Message: The storage adapter is disabled.
Action: If adapter disabled unexpectedly, re-enable the storage adapter.

HWC1009

Message: The backplane is absent.
LCD Message: The backplane is absent. Check hardware.
Details: The backplane may be necessary for proper operation. System functionality may be degraded.
Action: If removal was unintended, check presence, then reinstall or reconnect.

HWC1010

Message: The backplane is disabled.
Action: If disabled unexpectedly, re-enable backplane.

HWC1015

Message: The mezzanine card < number> is absent.
Details: The mezzanine card may be necessary for proper operation. System functionality may be degraded.
Action: If removal was unintended, check presence, then reinstall or reconnect.

HWC2006

Message: The < name> is not installed correctly.
LCD Message: The < name> is not installed correctly. Check connection.
Details: The device may be necessary for proper operation. System functionality may be degraded.
Action: Check presence, then re-install or reconnect.

HWC2008

Message: A fabric mismatch detected between IOM and mezzanine card < number>.
Details: The fabric type for the IOM and mezzanine cards must match.
Action: Check chassis fabric type in CMC GUI and compare to the type of IOM or mezzanine card.

HWC2011

Message: The riser board cable or interconnect is not connected, or is improperly connected.
LCD Message: Riser board cable or interconnect failure. Check connection.
Details: The riser blade cable may be necessary for proper operation. System functionality may be degraded.
Action: Check the riser board or interconnect presence, then reinstall or reconnect.

HWC3000

Message: The < name> is removed.
Details: The removed device may be necessary for proper operation. System functionality may be degraded.
Action: If removal was unintended, check presence of the removed device, then reinstall or reconnect

HWC3002

Message: Server < number> is removed.
Action: If removal was unintended, check presence of the server, then reinsert.

HWC3004

Message: IO module < number> is removed.
Action: If removal was unintended, check presence of the IO module, then reinsert.

HWC4000

Message: A hardware incompatibility detected between BMC/iDRAC firmware and CPU.
LCD Message: Incompatibility between BMC/iDRAC firmware and CPU. Update firmware.
Details: A hardware incompatibility was detected between BMC/iDRAC firmware and Processor(s). An iDRAC or BMC firmware update is needed.
Action: Update the BMC/iDRAC firmware. If the issue persists, see Getting Help.

HWC4002

Message: A hardware incompatibility detected between BMC/iDRAC firmware and other hardware.
Details: A hardware incompatibility was detected between BMC/iDRAC firmware and other hardware. An iDRAC or BMC firmware update is needed.
Action: Update the BMC/iDRAC firmware. If the issue persists, see Getting Help.

HWC4011

Message: Hardware unsuccessfully updated for mezzanine card < number>.
Action: Check presence of the hardware, reinstall or reconnect, then reattempt the update. If the issue persists, see Getting Help.

HWC4013

Message: Hardware unsuccessfully updated for embedded NIC.
Action: Check presence, reinstall or reconnect, then reattempt the update. If the issue persists, see Getting Help.

HWC4015

Message: Link Tuning error detected.
Details: CMC has old firmware. After updating the firmware the CMC will recognize the device.
Action: Update the CMC firmware. If the issue persists, see Getting Help.

HWC5001

Message: < name> is offline.
Action: If unexpected, check presence, then reinstall or reconnect.

HWC5002

Message: A fabric mismatch detected on < name>.
Details: The fabric type for the IOM and mezzanine cards must match.
Action: Check chassis fabric type in CMC GUI and compare to the type of IOM or mezzanine card.

HWC5004

Message: A link tuning failure detected on < name>.
Details: CMC has old firmware. After updating the firmware the CMC will recognize the device.
Action: Update the CMC firmware. If the issue persists, see Getting Help.

HWC5006

Message: A failure is detected on < name>.
Action: If the issue persists, see Getting Help.

HWC5008

Message: Console is not available for the < name>.
Action: If the issue persists, see Getting Help.

HWC5010

Message: < name> cannot detect any hosts.
Action: If the issue persists, see Getting Help.

HWC5014

Message: < name> is not functional and is powered off.
Action: If the issue persists, see Getting Help.

HWC5031

Message: IO module < number> is offline.
Details: The CMC has powered off the IOM.
Action: If the issue persists, see Getting Help.

HWC5032

Message: A fabric mismatch detected on IO module < number>.
Details: The fabric type for IOM's on the same chassis fabric must match.
Action: Check chassis fabric type in CMC GUI and compare to the type of both IOM's.

HWC5034

Message: A link tuning failure detected on IO module < number>.
Details: Link tuning table not supported for this IO modular.
Action: Update the CMC firmware. If the issue persists, see Getting Help.

HWC5036

Message: A failure is detected on IO module < number>.
Details: The IOM module performance may be impacted.
Action: If the issue persists, see Getting Help.

HWC6000

Message: The < name> controller is offline.
Details: Information and status from the controller is unavailable.
Action: Remove and reapply input power. If the issue persists, see Getting Help.

HWC6002

Message: The < name> controller is stuck in boot mode.
Details: Information and status from the controller is unavailable.
Action: Remove and reapply input power. If the issue persists, see Getting Help.

HWC6003

Message: The < name> controller is booting.

HWC6004

Message: Cannot communicate with < name> controller.
Details: Information and status from the controller is unavailable.
Action: Remove and reapply input power. If the issue persists, see Getting Help.

HWC7002

Message: Server < number> health changed to a warning state from a normal state.
Details: Server < number> health changed to a warning state from a normal state.
Action: Review System Log or front panel for additional information.

HWC7004

Message: Server < number> health changed to a critical state from either a normal or warning state.
Details: Server < number> health changed to a warning state from a normal state.
Action: Review System Log or front panel for additional information.

HWC7006

Message: Server < number> health changed to a nonrecoverable state from a less severe state.
Details: Server < number> health changed to a warning state from a normal state.
Action: Review System Log or front panel for additional information.

HWC7008

Message: Server < number> health changed to a warning state from more severe state. Server < number> health changed to a critical state from a non-recoverable state.
Details: Server < number> health changed to a warning state from a normal state.
Action: Review System Log or front panel for additional information.

HWC7010

Message: Server < number> health changed to a critical state from a nonrecoverable state.
Details: Server < number> health changed to a warning state from a normal state.
Action: Review System Log or front panel for additional information.

HWC7012

Message: Server < number> health changed to a nonrecoverable state.
Details: Server < number> health changed to a warning state from a normal state.
Action: Review System Log or front panel for additional information.

LNK2700

Message: The < name> LAN heartbeat is lost.
Details: CMC has lost network connection.
Action: Check network cable and network connections.

MEM0000

Message: Persistent correctable memory errors detected on a memory device at location(s) < location>.
Details: This is an early indicator of a possible future uncorrectable error.
Action: Re-seat the memory modules. If the issue persists, see Getting Help .

MEM0001

Message: Multi-bit memory errors detected on a memory device at location(s) < location>.
LCD Message: Multi-bit memory error on < location>. Re-seat memory.
Details: The memory module has encountered a uncorrectable error. System performance may be degraded. The operating system and/or applications may fail as a result.
Action: Re-seat the memory modules. If the issue persists, see Getting Help.

MEM0002

Message: Parity memory errors detected on a memory device at location < location>.
Details: The memory is operational. This an early indicator of a possible future uncorrectable error.
Action: Re-seat the memory modules. If the issue persists, see Getting Help.

MEM0003

Message: Stuck bit memory error detected on a memory device at location < location>.
Details: This is an early indicator of a possible future uncorrectable error.
Action: Re-seat the memory modules. If the issue persists, see Getting Help.

MEM0004

Message: Memory device at location < location> is disabled.
Details: The memory may not be seated correctly, misconfigured, or has failed. Memory size is reduced.
Action: Re-seat the memory modules. If the issue persists, see Getting Help.

MEM0005

Message: Persistent correctable memory error limit reached for a memory device at location(s) < location>.
LCD Message: Persistent correctable memory error limit reached for < location>. Re-seat memory.
Details: The memory is operational. This an early indicator of a possible future uncorrectable error.
Action: Re-seat the memory modules. If the issue persists, see Getting Help.

MEM0007

Message: Unsupported memory configuration; check memory device at location < location>.
LCD Message: Unsupported memory configuration. Check memory < location>.
Details: The memory may not be seated correctly, misconfigured, or has failed. Memory size is reduced.
Action: Check the memory configuration. Re-seat the memory modules. If the issue persists, see Getting Help.

MEM0009

Message: Memory device at location < location> is throttled.
Details: System performance is degraded.
Action: If unexpected, review system logs for power or thermal exceptions.

MEM0010

Message: Memory device at location < location> is over heating.
LCD Message: Memory device < location> is over heating. Check fans.
Details: System performance is degraded.
Action: If unexpected, review system logs for power or thermal exceptions.

MEM0022

Message: Memory device at location < location> is absent.
Details: The memory may not be seated correctly, misconfigured, or has failed. Memory size is reduced.
Action: Re-seat the memory modules. If the issue persists, see Getting Help.

MEM0701

Message: Correctable memory error rate exceeded for < location>.
Details: The memory may not be operational. This an early indicator of a possible future uncorrectable error.
Action: Re-seat the memory modules. If the issue persists, see Getting Help.

MEM0702

Message: Correctable memory error rate exceeded for < location>.
LCD Message: Correctable memory error rate exceeded for < location>. Re-seat memory.
Details: The memory may not be operational. This an early indicator of a possible future uncorrectable error.
Action: Re-seat the memory modules. If the issue persists, see Getting Help.

MEM1001

Message: Memory device at location < location> failed to transition to a running state.
LCD Message: Memory device < location> failed to transition to a running state. Re-seat memory
Details: The memory may not be operational. This an early indicator of a possible future uncorrectable error.
Action: Re-seat the memory modules. If the issue persists, see Getting Help.

MEM1003

Message: Memory device at location < location> failed to transition to in test.
Details: The memory may not be operational. This an early indicator of a possible future uncorrectable error.
Action: Re-seat the memory modules. If the issue persists, see Getting Help.

MEM1012

Message: Memory device at location < location> is in a degraded state.
Details: The memory may not be operational. This an early indicator of a possible future uncorrectable error.
Action: Re-seat the memory modules. If the issue persists, see Getting Help.

MEM1016

Message: Memory device at location < location> is not installed correctly.
LCD Message: Memory < location> is not installed correctly. Reinstall.
Details: The memory may not be seated correctly, misconfigured, or has failed. Memory size is reduced.
Action: Check the memory configuration. Re-seat the memory modules. If the issue persists, see Getting Help.

MEM1205

Message: Memory mirror redundancy is lost. Check memory device at location(s) < location>.
LCD Message: Memory mirror lost on < location>. Power cycle system.
Details: The memory may not be seated correctly, misconfigured, or has failed.
Action: Check the memory configuration. Re-seat the memory modules. If the issue persists, see Getting Help.

MEM1206

Message: Memory mirror redundancy is degraded. Check memory device at location < location>.
Details: The memory may not be seated correctly, misconfigured, or has failed.
Action: Check the memory configuration. Re-seat the memory modules. If the issue persists, see Getting Help.

MEM1208

Message: Memory spare redundancy is lost. Check memory device at location < location>.
LCD Message: Memory spare lost on < location>. Power cycle system.
Details: Memory sparing is no longer available.
Action: Re-seat the memory modules. If the issue persists, see Getting Help.

MEM1212

Message: Memory redundancy is lost.
Details: The memory may not be seated correctly, misconfigured, or has failed.
Action: Review system logs for memory exceptions. reinstall memory at location < location>

MEM1214

Message: Memory redundancy is degraded.
Details: The memory may not be seated correctly, misconfigured, or has failed.
Action: Check the memory configuration. Re-seat the memory modules. If the issue persists, see Getting Help.

MEM7002

Message: A hardware mismatch detected for memory riser.
LCD Message: Memory riser mismatch detected. Check memory riser.
Details: Memory riser is installed incorrectly, or failed.
Action: Check that the memory riser is installed correctly. If the issue persists, see Getting Help.

MEM8000

Message: Correctable memory error logging disabled for a memory device at location < location>.
LCD Message: SBE log disabled on < location>. Re-seat memory.
Details: Errors are being corrected but no longer logged.
Action: Review system logs for memory exceptions. reinstall memory at location < location>.

OSE0000

Message: A critical stop occurred during OS load.
Details: The system halted due to an exception during operating system load or operating system initialization.
Action: Review operating system logs and system video for additional information.

OSE0001

Message: A runtime critical stop occurred.
Details: The system halted due to an exception while the operating system was running. This is a kernel panic or bug check event.
Action: Review operating system logs and system video for additional information.

OSE0004

Message: A soft shut-down initiated by platform event filter.
Details: A separate exception or status condition shutdown the operating system. (IPMI sensor type 20h - offset 04h).
Action: Review system event log for platform events capable of shutting the system down.

OSE0005

Message: Agent is not responding.
Details: Graceful shutdown request to an agent via the BMC did not occur due to a system hardware or software exception.
Action: Review operating system logs and system video for additional information.

OSE1001

Message: Failed to boot from A.
Action: Review system boot configuration and boot media. Verify the media in a: is bootable. See system video for additional information.

OSE1003

Message: Failed to boot from C.
Action: Review system boot configuration and boot media. Verify the media in C: is bootable. See system video for additional information.

OSE1005

Message: PXE boot failed.
Action: Review system boot configuration, local PXE configuration, and PXE server configuration.

OSE1007

Message: Diagnostic boot failed.
Action: Review system boot configuration and boot media. See system video for additional information.

OSE1009

Message: Failed to boot from CD-ROM.
Action: Review system boot configuration and boot media. Verify the media in the CDROM is bootable. See system video for additional information.

OSE1011

Message: Failed to boot from ROM.
Action: Check system event logs for additional exception information. Power down the system and attempt to boot again.

OSE1013

Message: Failed to boot.
Action: Review system boot configuration and boot media. See system video for additional information.

PCI1302

Message: A bus time-out was detected on a component at bus < bus>device< device>function < func>.
Details: System performance may be degraded. The device has failed to respond to a transaction.
Action: Cycle input power, update component drivers, if device is removable, reinstall the device.

PCI1304

Message: An I/O channel check error was detected.
LCD Message: I/O channel check error detected. Power cycle system.
Action: Cycle input power, update component drivers, if device is removable, reinstall the device.

PCI1306

Message: A software error was detected on a component at bus < bus>device< device>function < func>.
Action: Reboot the system and update the component drivers.

PCI1308

Message: A PCI parity error was detected on a component at bus < bus>device< device>function < func>.
LCD Message: PCI parity error on bus < bus> device < device> function < func>. Power cycle system.
Details: System performance may be degraded, PCI device may fail to operate, or system may fail to operate.
Action: Cycle input power, update component drivers, if device is removable, reinstall the device.

PCI1310

Message: A PCI system error was detected on a component at bus < bus>device< device>function < func>.
LCD Message: PCI system error on bus < bus> device < device> function < func>. Power cycle system.
Details: System performance may be degraded, or system may fail to operate.
Action: Cycle input power, update component drivers, if device is removable, reinstall the device.

PCI1314

Message: A bus correctable error was detected on a component at bus < bus>device< device>function < func>.
Details: System performance may be degraded.
Action: Cycle input power, update component drivers, if device is removable reinstall the device at the next scheduled service time.

PCI1316

Message: A bus uncorrectable error was detected on a component at bus < bus>device< device>function < func>.
Details: System performance may be degraded, or system may fail to operate.
Action: Cycle input power, update component drivers, if device is removable, reinstall the device.

PCI1318

Message: A fatal error was detected on a component at bus < bus>device< device>function < func>.
LCD Message: Fatal error on bus < bus> device < device> function < func>. Power cycle system.
Details: System performance may be degraded, or system may fail to operate.
Action: Cycle input power, update component drivers, if device is removable, reinstall the device.

PCI1320

Message: A bus fatal error was detected on a component at bus < bus>device< device>function < func>.
LCD Message: Bus fatal error on bus < bus> device < device> function < func>. Power cycle system.
Details: System performance may be degraded, or system may fail to operate.
Action: Cycle input power, update component drivers, if device is removable, reinstall the device.

PCI1322

Message: Bus performance degraded for a component at bus < bus>device< device>function < func>.
Details: System performance may be degraded. The bus is not operating at maximum speed or width.
Action: Cycle input power, update component drivers, if device is removable, reinstall the device.

PCI1342

Message: A bus time-out was detected on a component at slot < number>.
Details: System performance may be degraded, or system may fail to operate.
Action: Cycle input power, update component drivers, if device is removable, reinstall the device.

PCI1344

Message: An I/O channel check error was detected.
LCD Message: An I/O channel check error was detected. Power cycle system.
Action: Cycle input power, update component drivers, if device is removable, reinstall the device.

PCI1346

Message: A software error was detected on a component at slot < number>.
Action: Reboot the system and update the component drivers.

PCI1348

Message: A PCI parity error was detected on a component at slot < number>.
LCD Message: PCI parity error on slot < number>. Re-seat PCI card.
Details: System performance may be degraded, or system may fail to operate.
Action: Cycle input power, update component drivers, if device is removable, reinstall the device.

PCI1350

Message: A PCI system error was detected on a component at slot < number>.
LCD Message: PCI parity error on slot < number>. Re-seat PCI card.
Details: System performance may be degraded, or system may fail to operate.
Action: Cycle input power, update component drivers, if device is removable, reinstall the device.

PCI1354

Message: A bus correctable error was detected on a component at slot < number>.
Details: System performance may be degraded.
Action: Cycle input power, update component drivers, remove and reinstall the device at the next scheduled service time.

PCI1356

Message: A bus uncorrectable error was detected on a component at slot < number>.
Details: System performance may be degraded, or system may fail to operate.
Action: Cycle input power, update component drivers, if device is removable, reinstall the device.

PCI1358

Message: A fatal error was detected on a component at slot < number>.
LCD Message: Fatal error on slot < number>. Re-seat PCI card.
Details: System performance may be degraded, or system may fail to operate.
Action: Cycle input power, update component drivers, if device is removable, reinstall the device.

PCI1360

Message: A bus fatal error was detected on a component at slot < number>.
LCD Message: Bus fatal error on slot < number>. Re-seat PCI card.
Details: System performance may be degraded, or system may fail to operate.
Action: Cycle input power, update component drivers, if device is removable, reinstall the device.

PCI1362

Message: Bus performance degraded for a component at slot < number>.
Details: System performance may be degraded. The bus is not operating at maximum speed or width.
Action: Cycle input power, update component drivers, remove and reinstall the device at the next scheduled service time.

PCI2000

Message: A fatal IO error detected on a component at bus < bus>device< device>function < func>.
LCD Message: Fatal IO error on bus < bus> device < device> function < func>.
Details: System performance may be degraded, or system may fail to operate.
Action: Cycle input power, update component drivers, remove and reinstall the device.

PCI2002

Message: A fatal IO error detected on a component at slot < number>.
LCD Message: Fatal IO error on slot < number>.
Details: System performance may be degraded, or system may fail to operate.
Action: Cycle input power, update component drivers, remove and reinstall the device.

PCI3000

Message: Device option ROM on embedded NIC failed to support Link Tuning or FlexAddress.
Details: Either the BIOS, BMC/iDRAC, or LOM firmware is out of date and does not support FlexAddress.
Action: Update BIOS, BMC/iDRAC, and LOM firmware. If the issue persists, see Getting Help .

PCI3002

Message: Failed to program virtual MAC address on a component at bus < bus>device< device>function < func>.
Details: Either the BIOS, BMC/iDRAC, LOM, or NIC firmware is out of date and does not support FlexAddress.
Action: Update BIOS, BMC/iDRAC, LOM, and mezzanine card firmware. If the issue persists, see Getting Help.

PCI3004

Message: Device option ROM on mezzanine card < number> failed to support Link Tuning or FlexAddress.
Details: Either the BIOS, BMC/iDRAC, or mezzanine card firmware is out of date and does not support FlexAddress.
Action: Update BIOS, BMC/iDRAC, and mezzanine card firmware. If the issue persists, see Getting Help.

PCI3006

Message: Failed to get Link Tuning or FlexAddress data from iDRAC.
Details: Either the BIOS or BMC/iDRAC firmware is out of date and does not support FlexAddress.
Action: Update BIOS, and BMC/iDRAC firmware. If the issue persists, see Getting Help.

PCI3008

Message: A non-fatal PCIe error detected on a component at bus < bus>device< device>function < func>.
Details: System performance may be degraded.
Action: Cycle input power, update component drivers, remove and reinstall the device at the next service window.

PCI3010

Message: A non-fatal IO error detected on a component at bus < bus>device< device>function < func>.
Details: System performance may be degraded.
Action: Cycle input power, update component drivers, remove and reinstall the device at the next service window.

PCI3012

Message: The QuickPath Interconnect (QPI) width degraded.
Details: System performance may be degraded. The bus is not operating at maximum speed or width.
Action: Reset the system, if the problem persists reinstall processors.

PCI3014

Message: A non-fatal PCIe error detected on a component at slot < number>.
Details: System performance may be degraded.
Action: Cycle input power, update component drivers, remove and reinstall the device at the next scheduled service time.

PDR0001

Message: Fault detected on drive < number>.
LCD Message: Fault detected on drive < number>. Check drive.
Details: The controller detected a failure on the disk and has taken the disk offline.
Action: Remove and re-seat the failed disk. If the issue persists, see Getting Help.

PDR0002

Message: A predictive failure detected on drive < number>.
Details: The controller received a SMART error from the drive. The drive is operational but needs replacement.
Action: The drive will need replacement at the next service window.

PDR0016

Message: Drive < number> is removed.
LCD Message: Drive < number> is removed. Check drive.
Details: The controller detected a drive removal.
Action: If unintended, verify drive installation. Remove and re-seat the indicated disk. If the issue persists, see Getting Help.

PDR1001

Message: Fault detected on drive < number> in disk drive bay < bay>.
LCD Message: Fault detected on drive < number> in disk drive bay < bay>. Check drive.
Details: The controller detected a failure on the disk and has taken the disk offline.
Action: Re-seat the failed drive. If the issue persists, see Getting Help.

PDR1002

Message: A predictive failure detected on drive < number> in disk drive bay< bay>.
Details: The controller received a SMART error from the drive. The drive is operational but needs replacement.
Action: The drive will need replacement at the next service window.

PDR1016

Message: Drive < number> is removed from disk drive bay < bay>.
LCD Message: Drive < number> removed from disk drive bay < bay>. Check drive.
Details: The controller detected that the drive was removed.
Action: Verify drive installation. Re-seat the failed drive. If the issue persists, see Getting Help.

PDR1024

Message: Drive mismatch detected for drive < number> in disk drive bay < bay>.
LCD Message: Drive mismatch detected for drive < number> in bay < bay>. Install correct drive type.
Details: The installed disk does not meet the array requirements, for example a SATA disk may not operate in an array containing SAS drives.
Action: Verify that the disk meets the array requirements.

PST0128

Message: No memory is detected.
LCD Message: No memory is detected. Inspect memory devices.
Details: System BIOS was unable to detect memory in the system .
Action: Re-seat the memory modules. If the issue persists, see Getting Help.

PST0129

Message: Memory is detected, but is not configurable.
LCD Message: Memory is detected, but is not configurable. Check memory devices.
Details: System BIOS detected memory, but was unable to configure the memory for system operation.
Action: Compare system memory installation to supported system memory configurations.

PST0130

Message: Memory is configured, but not usable.
LCD Message: Memory is configured, but not usable. Check memory devices
Details: The system BIOS encountered device failures or speed configurations that resulted in unused memory.
Action: Re-seat the memory modules. If the issue persists, see Getting Help.

PST0131

Message: System BIOS shadow failed.
LCD Message: System BIOS shadow failed. Check memory devices.
Details: Memory errors occurred copying BIOS image into system memory.
Action: Remove input power. Reduce system memory to minimum configuration and apply input power.

PST0132

Message: CMOS failed.
LCD Message: CMOS failed. Power cycle system.
Details: System BIOS detected a failure with CMOS memory during system POST.
Action: Check system event log for CMOS battery exceptions. Remove and reapply input power. If the issue persists, see Getting Help.

PST0133

Message: DMA controller failed.
LCD Message: DMA controller failed. Power cycle system.
Details: System BIOS detected a failure with the DMA controller during system POST.
Action: Remove and reapply input power.

PST0134

Message: Interrupt controller failed.
LCD Message: Interrupt controller failed. Power cycle system.
Details: System BIOS detected a failure with the interrupt controller during system POST.
Action: Remove and reapply input power. If the issue persists, see Getting Help.

PST0135

Message: Timer refresh failed.
LCD Message: Timer refresh failed. Power cycle system..
Details: System BIOS detected a timer refresh failure during system POST.
Action: Remove and reapply input power. If the issue persists, see Getting Help.

PST0136

Message: Programmable interval timer error.
LCD Message: Programmable interval timer error. Power cycle system.
Details: System BIOS detected an failure with the programmable interval timer during POST.
Action: Remove and reapply input power. If the issue persists, see Getting Help.

PST0137

Message: Parity error.
LCD Message: Parity error. Power cycle system.
Details: System BIOS detected a parity error during post.
Action: Remove and reapply input power. If the issue persists, see Getting Help.

PST0138

Message: SuperIO failed.
LCD Message: SuperIO failure. Power cycle system.
Details: System BIOS detected a failure with the SIO.
Action: Remove and reapply input power. If the issue persists, see Getting Help.

PST0139

Message: Keyboard controller failed.
LCD Message: Keyboard controller failed. Power cycle system.
Details: System BIOS detected a failure with the Keyboard Controller.
Action: Remove and reapply input power. If the issue persists, see Getting Help.

PST0140

Message: System management interrupt initialization failed.
LCD Message: SMI initialization failed. Power cycle system.
Details: System BIOS failed to initialize the system management interrupt.
Action: Remove and reapply input power. If the issue persists, see Getting Help.

PST0141

Message: QuickPath Interconnect (QPI) fatal error.
LCD Message: QuickPath Interconnect (QPI) fatal error.
Details: Quick Path Interconnect failed during system POST.
Action: Reboot the system. If problem persists, remove input power and re-seat processors.

PST0142

Message: MRC fatal error.
LCD Message: Memory initialization error.
Details: BIOS Memory testing failed.
Action: Compare system memory installation to supported system memory configurations. Reduce system configuration to minimum memory configuration.

PST0143

Message: Intel Trusted Execution Technology (TXT) fatal error.
LCD Message: Intel Trusted Execution Technology (TXT) fatal error.
Details: TXT boot failed. This could be related to memory errors or an error with the system TXT configuration. A socketed TPM module may have been removed.
Action: Check TPM presence. Remove and reapply input power. If the issue persists, see Getting Help.

PST0192

Message: Shut-down test failed.
LCD Message: Shut-down test failed. Power cycle system.
Details: System BIOS shutdown test failed during POST.
Action: Check system event log for CMOS battery exceptions. Remove and reapply input power. If the issue persists, see Getting Help.

PST0193

Message: BIOS POST memory test failed.
LCD Message: BIOS POST memory test failed. Check memory devices.
Details: System BIOS POST memory test failed.
Action: Compare system memory installation to supported system memory configurations. Reduce system configuration to minimum memory configuration.

PST0194

Message: Remote access controller configuration failed.
LCD Message: Remote access controller configuration failed. Check screen message.
Details: System BIOS could not configure the Remote Access controller.
Action: Cycle input power and power on the system. If the issue persists, see Getting Help .

PST0195

Message: CPU configuration failed.
LCD Message: CPU configuration failed. Check screen message.
Details: The current processor configuration is unsupported or encountered a fatal exception during POST.
Action: Review system processor configuration and reduce the system to the minimum configuration.

PST0196

Message: Incorrect memory configuration.
LCD Message: Incorrect memory configuration. Review User Guide.
Details: System BIOS detected an invalid memory population.
Action: Reinstall memory to match supported memory configuration.

PST0254

Message: General failure after video.
LCD Message: General failure after video. Check screen message.
Details: System BIOS detected a functional or configuration issue during system POST.
Action: Check system video and review event log for additional information.

PST0256

Message: POST fatal error detected.
LCD Message: POST fatal error detected.
Details: System BIOS detected a functional or configuration issue during system POST.
Action: Check system video and review event log for additional information.

PSU0001

Message: Power supply < number> failed.
LCD Message: PSU < number> failed. Check PSU.
Action: Remove and reinstall the power supply. If the issue persists, see Getting Help .

PSU0002

Message: A predictive failure detected on power supply < number>.
LCD Message: Predictive failure on PSU < number>. Check PSU.
Details: System performance and power redundancy may be degraded or lost.
Action: Remove and reinstall the power supply at the next service window. If the issue persists, see Getting Help.

PSU0003

Message: The power input for power supply < number> is lost.
LCD Message: Power input for PSU < number> is lost. Check PSU cables.
Details: The power supply is installed correctly but an input source is not connected or is not functional.
Action: Verify the input source is attached to the power supply. Verify the input power is within the operating requirements for the power supply.

PSU0004

Message: The power input for power supply < number> is outside of the allowable range.
LCD Message: Power input for PSU < number> is outside of range. Check PSU cables.
Details: The operating requirements for the power supply may be found in this manual or on the power supply itself.
Action: Verify the input source is attached to the power supply. Verify the input power is within the operating requirements for the power supply.

PSU0005

Message: The power input for power supply < number> is outside of the allowable range, but it is attached to the system.
Details: The operating requirements for the power supply may be found in this manual or on the power supply itself.
Action: Verify the input power is within the operating requirements for the power supply.

PSU0006

Message: Power supply < number> type mismatch.
LCD Message: Power supply < number> is incorrectly configured. Check PSU.
Details: Power supplies should be of the same input type and power rating.
Action: Install matched power supplies and review proper configuration in this manual.

PSU0007

Message: Power supply < number> is operating at 110 volts, and could cause a circuit breaker fault.
Details: A power supply that is designed to operate at 220V, but is connected to a 110V power source requires additional current for operation. The additional current may trip circuit-breakers or cause other electrical issues with the input source.
Action: Check input power source and cabling. Use recommended input power. Review this Manual. If the issue persists, see Getting Help.

PSU0008

Message: Power supply < number> voltage rating does not match the system's requirements.
Details: The system does not support mixed voltage power supplies.
Action: Install a power supply with the correct voltage rating.

PSU0016

Message

Power supply < number> is absent.

LCD Message

PSU < number> is absent. Check PSU.

Details

The supply has been removed or has failed.

Action

Remove and reinstall the power supply.
Check cables and subsystem components in the system for damage.
If the issue persists, see Getting Help.

PSU0031

Message: Cannot communicate with power supply < number>.
LCD Message: Cannot communicate with PSU < number>. Re-seat PSU.
Details: The power supply may operate, however power supply monitoring will be degraded. System performance may be degraded.
Action: Remove and reinstall the power supply. If the issue persists, see Getting Help .

PSU1201

Message: Power supply redundancy is lost.
Details: The power supply will try to operate in a degraded state. System Performance and power redundancy may be degraded or lost.
Action: Check input power. Reinstall the power supply. If the issue persists, see Getting Help .

PSU1202

Message: Power supply redundancy is degraded.
Details: The power supply will try to operate in a degraded state. System Performance and power redundancy may be degraded or lost.
Action: Remove input power and reinstall supply at the next service window.

PSU1203

Message: The power supplies are not redundant.
LCD Message: Lost PSU redundancy. Check PSU cables.
Details: The current power operational mode is non-redundant because of a power supply exception, a power supply inventory change, or a system power inventory change.
Action: Check the event log for power supply failures. Review system configuration and power consumption.

PSU1204

Message: The power supplies are not redundant. Insufficient resources to maintain normal operations.
LCD Message: PSU redundancy degraded. Check PSU cables.
Details: The current power operational mode is non-redundant because of a power supply exception, a power supply inventory change, or a system power inventory change.
Action: Check the event log for power supply failures. Review system configuration and power consumption.

PWR1001

Message: The system performance was degraded.
LCD Message: System performance degraded. Check PSUs and system configuration.
Details: To avoid shutdown, system performance has been degraded.
Action: Review system configuration and system logs for thermal or environmental failures and warnings.

PWR1002

Message: The system performance degraded because of thermal protection.
Details: To avoid shutdown, system performance has been degraded.
Action: Review system configuration and system logs for thermal or environmental failures and warnings.

PWR1003

Message: The system performance degraded because cooling capacity has changed.
Details: The current power supply configuration does not meet the platform requirements to enable redundancy. If a power supply fails the system may shutdown.
Action: If unintended, review system configuration and power consumption and install power supplies accordingly. Check power supply status for failures.

PWR1004

Message: The system performance degraded because power capacity has changed.
Details: The system may power down or operate in a performance degraded state.
Action: Check the event log for power supply failures. Review system configuration and power consumption and upgrade or install power supplies accordingly.

PWR1005

Message: The system performance degraded because the user-defined power capacity has changed.
Details: The user-defined power settings have affected system operation.
Action: If unintended, review system configuration changes and power policy.

PWR1006

Message: The system halted because system power exceeds capacity.
LCD Message: System power demand exceeds capacity. System halted.
Details: The system halted because system power exceeds capacity.
Action: Review system configuration, upgrade power supplies or reduce system power consumption.

PWR1007

Message: The system performance degraded because power exceeds capacity.
LCD Message: System power exceeds capacity. Performance degraded. Check PSU configuration.
Details: The system is currently operating in a performance degraded state to attempt protect from a power shutdown.
Action: Review system configuration, upgrade power supplies or reduce system power consumption.

PWR1008

Message: The system performance degraded because power draw exceeds the power threshold.
LCD Message: System power exceeds threshold. Performance degraded. Check PSU configuration.
Details: The power threshold is configured by the user or automatically by software based on system configuration.
Action: Review system configuration, upgrade power supplies or reduce system power consumption.

RFM1003

Message: Removable Flash Media < name> is not IPMI-function ready.
Details: The removable flash media is installed but improperly configured or failed to initialize.
Action: If unintended, reinstall the flash media and module.

RFM1005

Message: Removable Flash Media < name> is not ready.
Details: The media is being prepared or is under maintenance. If the problem persists, reinstall the card.
Action: Wait for the media to be ready.

RFM1006

Message: Removable Flash Media < name> is offline.
Details: At boot, the Card Identification (CID) signature of the card is different from the Non-volatile (NV) storage value or the card is the destination of a copy operation that is in-progress.
Action: If unintended, reinstall the flash media.

RFM1008

Message: Failure detected on Removable Flash Media < name>.
LCD Message: Removable Flash Media < name> failed. Check SD Card.
Details: An error was reported during a SD card read or write.
Action: Reseat the flash media, if the issue persists replace the media.

RFM1014

Message: Removable Flash Media < name> is write protected.
LCD Message: Removable Flash Media < name> is write protected. Check SD Card.
Details: The card is write-protected by the physical latch on the SD card. A write-protected card cannot be used.
Action: If unintended, remove the media and disable write protection.

RFM1016

Message: Media not present for Removable Flash Media < name>.
Details: The SD card is not detected or not installed.
Action: If unintended, reinstall the flash media.

RFM1021

Message: Removable Flash Media is not IPMI-function ready.
Details: The removable flash media is installed but improperly configured or failed to initialize.
Action: If unintended, reinstall the flash media.

RFM1022

Message: Removable Flash Media is ready.
Action: If unintended, reinstall the flash media.

RFM1023

Message: Removable Flash Media is not ready.
Details: The media is being prepared or is under maintenance. If the problem persists, reinstall the card.
Action: If unintended, reinstall the flash media.

RFM1024

Message: Removable Flash Media is offline.
Details: At boot, the Card Identification (CID) signature of the card is different from the Non-volatile (NV) storage value or the card is the destination of a copy operation that is in-progress.
Action: If unintended, reinstall the flash media.

RFM1026

Message: Failure detected on Removable Flash Media.
Details: An error is reported during a SD card read or write.
Action: Reinstall the flash media, if the issue persists replace the media.

RFM1032

Message: Removable Flash Media is write protected.
Details: The card is write-protected by the physical latch on the SD card. IDSDM cannot use a write-protected card.
Action: If unintended, remove the media and disable write protection.

RFM1034

Message: Media not present for Removable Flash Media.
Details: The SD card is not detected or not installed.
Action: If unintended, reinstall the flash media.

RFM1201

Message: Internal Dual SD Module redundancy is lost.
LCD Message: Internal Dual SD Module redundancy is lost. Check SD Card.
Details: Either one of the SD card or both the SD cards are not functioning properly.
Action: Replace the failed SD card.

RFM1202

Message: Internal Dual SD Module redundancy is degraded.
Details: Either one of the SD card or both the SD cards are not functioning properly.
Action: Replace the failed SD card.

RFM1203

Message: Internal Dual SD Module is not redundant.
Details: Internal Dual SD Module is not redundant.
Action: Install additional SD card and configure for redundancy if redundancy is desired.

RFM1205

Message: Internal Dual SD Module is not redundant. Insufficient resources to maintain normal operations.
LCD Message: Internal Dual SD Module is not redundant. Insufficient resources. Check SD Card.
Details: The current operating configuration cannot maintain redundancy. The unit may operate in a degraded state.
Action: Review this manual and SD card configuration.

RFM2001

Message: Internal Dual SD Module < name> is absent.
LCD Message: Internal Dual SD Module < name> is absent. Check SD Card.
Details: The SD card module is not detected or not installed.
Action: If unintended, reinstall the SD module.

RFM2002

Message: Internal Dual SD Module < name> is offline.
Details: The SD card module is installed but may be improperly installed or configured incorrectly.
Action: Reinstall the SD module.

RFM2004

Message: Failure detected on Internal Dual SD Module < name>.
LCD Message: Internal Dual SD Module < name> failed. Check SD Card.
Details: The SD card module is installed but improperly configured or failed to initialize.
Action: Reinstall the SD module and remove and reinstall SD cards.

RFM2006

Message: Internal Dual SD Module < name> is write protected.
Details: The module is write-protected. Changes may not be written to the media.
Action: If unintended, remove the media and disable write protection.

SEC0000

Message: The chassis is open.
LCD Message: Intrusion detected. Check chassis cover.
Details: The chassis is open. System performance may be degraded, and security may be compromised.
Action: Close the chassis. Check system logs.

SEC0001

Message: The drive bay is open.
Details: The drive bay is open. A drive may be added or removed. System performance may be degraded.
Action: Close the drive bay. Check system logs.

SEC0002

Message: The I/O card area is open.
Details: The I/O card area is open. I/O cards may be added or removed. System performance may be degraded.
Action: Close the I/O card area. Check system logs.

SEC0003

Message: The processor area is open.
Details: The processor area is open. A drive may be added or removed. System performance may be degraded.
Action: Close the processor area. Check system logs.

SEC0004

Message: The LAN is disconnected.
Details: The LAN is disconnected. Network performance may be degraded.
Action: If unintentional, connect network cable.

SEC0005

Message: Unauthorized docking is detected.
Details: A removable component may have been tampered with, or installed incorrectly, or does not meet system requirements.
Action: Check removable hardware components for correct installation. Review installation documentation.

SEC0006

Message: The fan area is open.
Details: The fan area is open. System performance may be degraded.
Action: Close the fan area. Check system logs.

SEC0031

Message: The chassis is open while the power is on.
LCD Message: Intrusion detected. Check chassis cover.
Details: The chassis is open. System performance may be degraded, and security may be compromised.
Action: Close the chassis. Check system logs.

SEC0033

Message: The chassis is open while the power is off.
LCD Message: Intrusion detected. Check chassis cover.
Details: The chassis was opened while the power was off. System security may have been comprised.
Action: Close the chassis and verify hardware inventory. Check system logs.

SEC0040

Message: A critical stop occurred during OS load.
Details: Operating system generated critical stop IPMI event. (Sensor type code = 20H)
Action: Check video and operating system logs for additional information

SEC0041

Message: BIOS detected an error configuring the Intel Trusted Execution Technology (TXT).
LCD Message: BIOS detected an error configuring TXT. Check system configuration.
Details: TXT initialization failure. System configuration may have changed.
Action: Check system hardware inventory and software configuration.

SEC0042

Message: Processor detected an error while performing an Intel Trusted Execution Technology (TXT) operation.
LCD Message: CPU detected an error while performing a TXT operation. Check system configuration.
Details: TXT CPU microcode boot failure. System configuration may have changed.
Action: Check system hardware inventory and software configuration.

SEC0043

Message: BIOS Authenticated Code Module detected an Intel Trusted Execution Technology (TXT) error during POST.
LCD Message: BIOS detected a TXT error during POST. Check system configuration.
Details: TXT Post failure. System configuration may have changed.
Action: Check system hardware inventory and software configuration.

SEC0044

Message: SINIT Authenticated Code Module detected an Intel Trusted Execution Technology (TXT) error at boot.
LCD Message: SINIT detected a TXT error at boot. Check system configuration.
Details: TXT initialization failure. System configuration may have changed.
Action: Check system hardware inventory and software configuration.

SEC0600

Message: A secure mode violation detected.
Details: This may apply to a physical or remote access attempt.
Action: Check system logs for intrusion attempts, and ensure strong password policies.

SEC0602

Message: User password violation detected.
Details: This may apply to a physical or remote access attempt.
Action: Check system logs for intrusion attempts, and ensure strong password policies.

SEC0604

Message: A setup password violation detected.
Details: This may apply to a physical or remote access attempt.
Action: Check system logs for intrusion attempts, and ensure strong password policies.

SEC0606

Message: The network boot password violation detected.
Details: This may apply to a physical or remote access attempt.
Action: Check system logs for intrusion attempts, and ensure strong password policies.

SEC0608

Message: A password violation detected.
Details: This may apply to a physical or remote access attempt.
Action: Check system logs for intrusion attempts, and ensure strong password policies.

SEC0610

Message: An Out-of-band password violation detected.
Details: This may apply to a remote access attempt.
Action: Check system logs for intrusion attempts, and ensure strong password policies.

SEL0002

Message: Logging is disabled.
Details: This message is displayed when event logging of a specific type is disabled by the user.
Action: If unintended, re-enable logging.

SEL0006

Message: All event logging is disabled.
Details: This message is displayed when all event logging has been disabled by the user.
Action: If unintended, re-enable logging.

SEL0008

Message: Log is full.
Details: When the event log is full, additional events are not written to the log. Older events may be overwritten and lost. This message may also appear if the user disabled event logging.
Action: Backup and clear log.

SEL0010

Message: Log is almost full.
Details: When the event log is full, additional events are not written to the log. Older events may be overwritten and lost.
Action: Backup and clear log at the next maintained time.

SEL0012

Message: Could not create or initialize the system event log.
Details: If the system event log fails to initialize, platform status and failure events are not captured. Some management software do not report platform exceptions.
Action: Reboot the management controller or iDRAC. Cycle system input power. If problem persists call support.

SEL1204

Message: An unknown system hardware failure detected.
LCD Message: Unknown system hardware failure.
Details: If the system event log failed to initialize platform status and failure events are not captured. Some management software will not report platform exceptions.
Action: Re-configure system to minimum supported configuration. If issues persists, contact support.

SEL1209

Message: The platform event filter action failed.
Details: System policies or permissions may prevent the action from executing. If configured, the system does not execute the action on a platform event (such as power down, cycle, interrupt, and send alert).
Action: Review platform event configuration.

SEL1211

Message: The time-stamp clock could not be synchronized.
Details: The time stamp on system event log events may not correlate to the system time.
Action: Cycle system input power. If problem persists, contact support.

SEL1300

Message: No bootable media found.
Details: System setup displays the system boot order. The local video screen may also show additional information. (IPMI sensor type code 1eh - offset 00h).
Action: Check system boot settings. Check if mass storage controller configuration settings are applicable.

SEL1302

Message: Non-bootable diskette detected.
Details: The disk in the drive is not formatted correctly or does not contain the necessary operating system files.
Action: Replace diskette with a bootable disk.

SEL1304

Message: The PXE server not found.
Details: PXE is one way to boot a system from the network.
Action: Check the network and PXE server configuration.

SEL1306

Message: Invalid boot sector found.
Details: The disk in the drive is not formatted correctly or does not contain the necessary operating system files.
Action: Replace diskette with a bootable disk.

SEL1308

Message: A time-out occurred while waiting for user to select a boot source.
Details: The system has failed to boot to an operating system and needs the user to select a boot source.
Action: Select boot source within the time allowed.

SEL1501

Message: Chassis management controller (CMC) redundancy is lost.
Details: An action or failure has taken place that breaks CMC redundancy.
Action: Check the CMC network cables and network connections. Check that CMC firmware versions match.

SEL1502

Message: Chassis management controller (CMC) redundancy is degraded.
Details: An action or failure has taken place that breaks CMC redundancy.
Action: Check the CMC network cables and network connections. Check that CMC firmware versions match.

SEL1504

Message: The chassis management controller (CMC) is not redundant. Insufficient resources to maintain normal operations.
Details: There is not enough available power for two CMC's to operate.
Action: Check the overall power consumption and power status.

SEL1506

Message: Lost communications with Chassis Group Member < number>.
Details: The primary CMC has lost communication with the indicated member CMC.
Action: Check the network cable and network connections.

SEL1508

Message: Member < number> could not join the Chassis Group.
Details: The indicated member CMC is a leader of a different CMC stacking group.
Action: Check if member CMC is a leader of a different chassis group.

SEL1510

Message: An authentication error detected for Chassis Group Member < number>.
Details: Group master CMC could not log into the group member CMC.
Action: Check the login credentials of CMC.

SEL9900

Message: An unsupported event occurred.
Details: The current software version cannot decode this event. You may need to review this event using a tool which displays raw data such as Ipmitool with the -vvv option or Racadm with the -E option.
Action: Upgrade the management software.

SWC4004

Message: A firmware or software incompatibility detected between iDRAC in slot < number> and CMC.
Details: FlexAddress is not implemented in one of the versions of firmware.
Action: Check the firmware versions of iDRAC and CMC. Update with the latest version.

SWC4006

Message: A firmware or software incompatibility detected between system BIOS in slot < number> and CMC.
Details: FlexAddress is not implemented in one of the versions of firmware.
Action: Check the firmware versions of BIOS and CMC. Update with the latest version.

SWC4008

Message: A firmware or software incompatibility detected between CMC 1 and CMC 2.
Details: FlexAddress is not implemented in one of the versions of firmware. Please update the firmware.
Action: Check firmware versions. Update CMC 1 and CMC 2 firmware to match.

SWC5001

Message: < name> upgrade failed.
Action: Reboot the system and attempt the upgrade again.

TMP0100

Message: The system board < name> temperature is less than the lower warning threshold.
LCD Message: System board < name> temperature is outside of range.
Details: Ambient air temperature is too cool.
Action: Check the system operating environment.

TMP0101

Message: The system board < name> temperature is less than the lower critical threshold.
LCD Message: System board < name> temperature is outside of range.
Details: Ambient air temperature is too cool.
Action: Check the system operating environment.

TMP0102

Message: The system board < name> temperature is greater than the upper warning threshold
LCD Message: System board < name> temperature is outside of range.
Details: Ambient air temperature is too warm or one or more fans may have failed.
Action: The system board < name> temperature is outside of the optimum range. Check the fans.

TMP0103

Message: The system board < name> temperature is greater than the upper critical threshold.
LCD Message: System board < name> temperature is outside of range.
Details: Ambient air temperature is too warm or one or more fans may have failed.
Action: The system board < name> temperature is outside of the optimum range. Check the fans.

TMP0104

Message: The system board < name> temperature is outside of range.
LCD Message: System board < name> temperature is outside of range.
Details: Ambient air temperature is too warm or cool.
Action: The system board < name> temperature is outside of the optimum range. Check Fans.

TMP0106

Message: The memory module < number> temperature is less than the lower warning threshold.
LCD Message: Memory module < number> temperature is outside of range.
Details: Ambient air temperature is too cool.
Action: Check the system operating environment.

TMP0107

Message: The memory module < number> temperature is less than the lower critical threshold.
LCD Message: Memory module < number> temperature is outside of range.
Details: Ambient air temperature is too cool.
Action: Check the system operating environment.

TMP0108

Message: The memory module < number> temperature is greater than the upper warning threshold.
LCD Message: Memory module < number> temperature is outside of range. Check Fans.
Details: Ambient air temperature is too warm or one or more fans may have failed.
Action: The system board < name> temperature is outside of the optimum range. Check Fans.

TMP0109

Message: The memory module < number> temperature is greater than the upper critical threshold.
LCD Message: Memory module < number> temperature is outside of range. Check Fans.
Details: Ambient air temperature is too warm or one or more fans may have failed.
Action: The system board < name> temperature is outside of the optimum range. Check Fans.

TMP0110

Message: The memory module < number> temperature is outside of range.
LCD Message: Memory module < number> temperature is outside of range. Check Fans.
Details: Ambient air temperature is too warm or cool.
Action: Check the system operating environment.

TMP0112

Message: The < name> temperature is less than the lower warning threshold.
LCD Message: The < name> temperature is outside of range.
Details: Ambient air temperature is too cool.
Action: Check the system operating environment.

TMP0113

Message: The < name> temperature is less than the lower critical threshold.
LCD Message: The < name> temperature is outside of range.
Details: Ambient air temperature is too cool.
Action: Check the system operating environment.

TMP0114

Message: The < name> temperature is greater than the upper warning threshold.
LCD Message: The < name> temperature is outside of range. Check Fans
Details: Ambient air temperature is too warm or one or more fans may have failed.
Action: Check the system operating environment and review event log for fan failures.

TMP0115

Message: The < name> temperature is greater than the upper critical threshold.
LCD Message: The < name> temperature is outside of range. Check Fans
Details: Ambient air temperature is too warm or one or more fans may have failed.
Action: Check the system operating environment and review event log for fan failures.

TMP0116

Message: The < name> temperature is outside of range.
LCD Message: The < name> temperature is outside of range. Check Fans
Action: Check the system operating environment and review event log for fan failures.

TMP0118

Message: The system inlet temperature is less than the lower warning threshold.
LCD Message: System inlet temperature is outside of range.
Details: Ambient air temperature is too cool.
Action: Check the system operating environment.

TMP0119

Message: The system inlet temperature is less than the lower critical threshold.
LCD Message: System inlet temperature is outside of range.
Details: Ambient air temperature is too cool.
Action: Check the system operating environment.

TMP0120

Message: The system inlet temperature is greater than the upper warning threshold.
LCD Message: System inlet temperature is outside of range.
Details: Ambient air temperature is too warm or one or more fans may have failed.
Action: Check the system operating environment and review event log for fan failures.

TMP0121

Message: The system inlet temperature is greater than the upper critical threshold.
LCD Message: System inlet < name> temperature is outside of range. Check Fans.
Details: Ambient air temperature is too warm or one or more fans may have failed.
Action: Check the system operating environment and review event log for fan failures.

TMP0122

Message: The system inlet temperature is outside of range.
LCD Message: System inlet < name> temperature is outside of range. Check Fans.
Details: Ambient air temperature is too warm or cool.
Action: Check the system operating environment and review event log for fan failures.

TMP0100

Message: Disk drive bay temperature is less than the lower warning threshold.
Details: Ambient air temperature is too cool.
Action: Check the system operating environment.

TMP0104

Message: Disk drive bay temperature is less than the lower critical threshold.
LCD Message: Disk drive bay temperature is outside of range. Check Fans.
Details: Ambient air temperature is too cool.
Action: Check the system operating environment.

TMP0126

Message: Disk drive bay temperature is greater than the upper warning threshold.
LCD Message: Disk drive bay temperature is outside of range. Check Fans.
Details: Ambient air temperature is too warm or one or more fans may have failed.
Action: Check the system operating environment and review event log for fan failures.

TMP0128

Message: Disk drive bay temperature is outside of the allowable range.
LCD Message: Disk drive bay temperature is outside of range. Check Fans.
Details: Ambient air temperature is too warm or cool.
Action: Check the system operating environment and review event log for fan failures.

TMP0130

Message: The control panel temperature is less than the lower warning threshold.
LCD Message: Control panel temperature is outside of range.
Details: Ambient air temperature is too cool.
Action: Check the system operating environment.

TMP0132

Message: The control panel temperature is greater than the upper warning threshold.
LCD Message: Control panel temperature is outside of range.
Details: Ambient air temperature is too warm or one or more fans may have failed.
Action: Check the system operating environment and review event log for fan failures.

TMP0134

Message: The control panel temperature is outside of the allowable range.
LCD Message: Control panel temperature is outside of range.
Details: Ambient air temperature is too warm or cool.
Action: Check the system operating environment and review event log for fan failures.

VLT0100

Message

Processor module < name> voltage is less than the lower warning threshold.

LCD Message

Processor module < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Remove the processor module. Inspect processor socket for bent pins.
If the issue persists, see Getting Help.

VLT0101

Message

Processor module < name> voltage is less than the lower critical threshold.

LCD Message

Processor module < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Remove the processor module. Inspect processor socket for bent pins.
If the issue persists, see Getting Help.

VLT0102

Message

Processor module < name> voltage is greater than the upper warning threshold.

LCD Message

Processor module < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Remove the processor module. Inspect processor socket for bent pins.
If the issue persists, see Getting Help.

VLT0103

Message

Processor module < name> voltage is greater than the upper critical threshold.

LCD Message

Processor module < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Remove the processor module. Inspect processor socket for bent pins.
If the issue persists, see Getting Help.

VLT0104

Message

Processor module < name> voltage is outside of the allowable range.

LCD Message

Processor module < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Remove the processor module. Inspect processor socket for bent pins.
If the issue persists, see Getting Help.

VLT0200

Message

The system board < name> voltage is less than the lower critical threshold.

LCD Message

System board voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Remove the processor module. Inspect processor socket for bent pins.
If the issue persists, see Getting Help.

VLT0201

Message

The system board < name> voltage is less than the lower warning threshold.

LCD Message

System board voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0202

Message

The system board < name> voltage is greater than the upper warning threshold.

LCD Message

System board voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0203

Message

The system board < name> voltage is greater than the upper critical threshold.

LCD Message

System board voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0204

Message

The system board < name> voltage is outside of the allowable range.

LCD Message

System board voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0206

Message

The memory module < number> < name> voltage is less than the lower warning threshold.

LCD Message

Memory module < number> < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0207

Message

The memory module < number> < name> voltage is less than the lower critical threshold.

LCD Message

Memory module < number> < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0208

Message

The memory module < number> < name> voltage is greater than the upper warning threshold.

LCD Message

Memory module < number> < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0209

Message

The memory module < number> < name> voltage is greater than the upper critical threshold.

LCD Message

Memory module < number> < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0210

Message

The memory module < number> < name> voltage is outside of range.

LCD Message

Memory module < number> < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0212

Message

The disk drive bay < name> voltage is less than the lower warning threshold.

LCD Message

The disk drive bay < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0213

Message

The disk drive bay < name> voltage is less than the lower critical threshold.

LCD Message

The disk drive bay < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0214

Message

The disk drive bay < name> voltage is greater than the upper critical threshold.

LCD Message

The disk drive bay < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0215

Message

The disk drive bay < name> voltage is greater than the upper critical threshold.

LCD Message

The disk drive bay < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0216

Message

The < name> voltage is outside of range.

LCD Message

The < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0218

Message

The < name> voltage is less than the lower warning threshold.

LCD Message

The < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0219

Message

The < name> voltage is less than the lower critical threshold.

LCD Message

The < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0220

Message

The < name> voltage is greater than the upper warning threshold.

LCD Message

The < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0221

Message

The < name> voltage is greater than the upper critical threshold.

LCD Message

The < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0222

Message

The < name> voltage is outside of range.

LCD Message

The < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0224

Message

The memory module < name> voltage is less than the lower warning threshold.

LCD Message

Memory module < number> < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0225

Message

The memory module < name> voltage is less than the lower critical threshold.

LCD Message

Memory module < number> < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0226

Message

The memory module < name> voltage is greater than the upper warning threshold.

LCD Message

Memory module < number> < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0227

Message

The memory module < name> voltage is greater than the upper critical threshold.

LCD Message

Memory module < number> < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0228

Message

The memory module < name> voltage is outside of range.

LCD Message

Memory module < number> < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-configure the system to minimum configuration, inspect and reinstall system cables.
If the issue persists, see Getting Help.

VLT0230

Message

The mezzanine card < number> < name> voltage is less than the lower warning threshold.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-seat the mezzanine card.
If the issue persists, see Getting Help.

VLT0231

Message

The mezzanine card < number> < name> voltage is less than the lower critical threshold.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-seat the mezzanine card.
If the issue persists, see Getting Help.

VLT0232

Message

The mezzanine card < number> < name> voltage is greater than the upper warning threshold.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-seat the mezzanine card.
If the issue persists, see Getting Help.

VLT0233

Message

The mezzanine card < number> < name> voltage is greater than the upper critical threshold.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-seat the mezzanine card.
If the issue persists, see Getting Help.

VLT0234

Message

The mezzanine card < number> < name> voltage is outside of range.

Details

System hardware detected an over voltage or under voltage condition.

If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode.

Action

Review system logs for power supply exceptions.
Re-seat the mezzanine card.
If the issue persists, see Getting Help.

Welcome

Welcome to Dell

Dell PowerEdge M620 Systems Owner's Manual

System Error Messages

Rate this content