The Dell PowerEdge R630 is available in several
hot- plug, hard- drive chassis options, as detailed in the table below.
NOTE The chassis option
must be selected during purchase and cannot be changed or upgraded
later.
Storage
Options
Config #
Chassis
Controller Qty
Base Config #
Backplane Description
Storage Controller(s)
1
R630
1
ASSY,CHAS,2.5X8,R630
2 PCIe Slots
8 X 2.5 SAS/SATA BP
PERC S130, H330, H730, H730P
2
R630
1
ASSY,CHAS,2.5X8,R630
3 PCIe Slots
8 X 2.5 SAS/SATA BP
PERC S130, H330, H730, H730P
3
R630
1
ASSY,CHAS,2.5X10,R630
10 X 2.5" SAS/SATA BP
PERC H330, H730, H730P
4
R630
1
ASSY,CHAS,2.5X6 +4,R630
10 X 2.5" SAS/SATA BP w/ PCIe SSD
PERC H330, H730, H730P
5
R630
1 or 2
ASSY,CHAS,1.8X24,R630
24 X 1.8" SATA BP
PERC H330, H730, H730P
SAS Backplane Features
All backplanes with eight or fewer hard drive slots
have SEP circuitry implemented. For R630, because of power- and planar
space limitations, all backplanes implement a 5V VR on the backplane,
accomodate for the backplane HDD count. 12 V power is delivered through
Power cable(s) to the backplanes.
All backplanes
use a common sideband connector and connector pin-out for miscellaneous
signals and I2C signals from the system iDRAC to the SEP. The sideband
connector also carries 3.3V for all SAS backplanes. One pin is reserved
for 3.3V AUX. This pin is left as no-connect on the SAS backplanes.
On the PCIe backplane, the 3.3V AUX is routed to each SSD drive.This
enables the SSD slot being PCIe slot specific capable.
All SAS backplanes are designed and validated to meet 12Gbps SAS
and 6Gbps SATA requirements.
SAS Expander Daughter
Card
The SAS expander daughter card is necessary
to achieve higher single-volume hard drive configurations. An integrated
expander device limits the hard drive footprint. A daughter card allows
PowerEdge R730 and R730xd to maximize the hard drive space in the
hard drive bay.
A single expander daughter card
supports the 16 hard drive configuration. The expander daughter card
is integrated with the 16 hard drive primary backplane by using Xcede
HD and power connectors.
The key implementation
features of the Expander Daughter Card are:
Four 4x MiniSAS connectors: two for the internal
storage controller, and two for an optional daisy chain board to extend
the HDD count.
One eSATA port footprint (not populated for OEM solutions
with x36 expander).
One LSI SAS3 x36 Edge Expander:
Provide connection between initiators and targets.
Support SSP, STP, and SMP protocols.
Internal BP SEP that communicates with the RAID controller
by using SES pages over i2C and with the system iDRAC over i2C.
Support 12 Gbps SAS, 12 Gbps SAS and 6 Gbps SATA.
Expander Flash ROM:
4 MB part. Stores the expander firmware image.
Xcede connectors for low speed misc. signals and
high speed SAS signals between the DC and the primary backplane.
Internal Expander SEP for platform specific firmware
settings.
Active backplane with the expansion redriver
card is supported.
Data is not available for the Topic
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\