- About this Guide
- Notes, Cautions, and Warnings
- About the SCv2000/SCv2020 Storage System
- Storage Center Hardware Components
- Storage Center Architecture Options
- Storage Center Communication
- SCv2000/SCv2020 Storage System Hardware
- SC100/SC120 Expansion Enclosure Overview
- Install the Storage Center Hardware
- Connect the
Front End
- Types of Redundancy for Front-End Connections
- Cabling SAN-Attached
Host Servers
- Connecting to
Fibre Channel Host Servers
- Preparing Host Servers
- Two Fibre Channel Fabrics with Dual 16 Gb 2-Port Storage Controllers
- Two Fibre Channel Fabrics with Dual 8 Gb 4-Port Storage Controllers
- One Fibre Channel Fabric with Dual 16 Gb 2-Port Storage Controllers
- One Fibre Channel Fabric with Dual 8 Gb 4-Port Storage Controllers
- Two Fibre Channel Fabrics with a Single 16 Gb 2-Port Storage Controller
- Two Fibre Channel Fabrics with a Single 8 Gb 4-Port Storage Controller
- Using SFP+ Transceiver Modules
- Fibre Channel Zoning
- Labeling the Front-End Cables
- Connecting to
iSCSI Host Servers
- Preparing Host Servers
- Two iSCSI Networks with Dual 10 GbE 2–Port Storage Controllers
- Two iSCSI Networks with Dual 1 GbE 4-Port Storage Controllers
- One iSCSI Network with Dual 10 GbE 2-Port Storage Controllers
- One iSCSI Network with Dual 1 GbE 4-Port Storage Controllers
- Two iSCSI Networks with a Single 10 GbE 2-Port Storage Controller
- Two iSCSI Networks with a Single 1 GbE 4-Port Storage Controller
- Labeling the Front-End Cables
- Connecting to
Fibre Channel Host Servers
- Cabling Direct-Attached Host Servers
- Cabling the Ethernet Management Port
- Cabling the Embedded Ports for iSCSI Replication
- Cabling the Embedded Ports for iSCSI Host Connectivity
- Back-End Cabling and Connecting Power
- Discover and
Configure the Storage Center
- Locating Your Service Tag
- Worksheet to Record System Information
- Supported Operating Systems for Storage Center Automated Setup
- Install and Use the Dell Storage Client
- Discover and Select an Uninitialized Storage Center
- Set System Information
- Set Administrator Information
- Configure iSCSI Fault Domains
- Confirm the Storage Center Configuration
- Initialize the Storage Center
- Review Fibre Channel Front-End Configuration
- Review SAS Front-End Configuration
- Configure Time Settings
- Configure SMTP Server Settings
- Configure Key Management Server Settings
- Review the SupportAssist Data Collection and Storage Agreement
- Provide Contact Information
- Update Storage Center
- Complete Configuration and Perform Next Steps
- Set Up a localhost or VMware Host
- Configure Embedded iSCSI Ports
- Perform Post-Setup Tasks
- Adding or Removing an Expansion Enclosure
- Troubleshooting Storage Center Deployment
Dell Storage Center SCv2000 and SCv2020 Storage System Deployment Guide
MPIO Configuration Instructions for Host Servers
To use MPIO, configure MPIO on the host server.
If a Dell Storage Client wizard is used to configure host server access to the Storage Center, the Dell Storage Client attempts to automatically configure MPIO with best practices.
- NOTE: Compare the host server settings applied by the Dell Storage Client wizard against the latest Dell Storage Center Best Practices document on the Dell TechCenter site ( http://en.community.dell.com/techcenter/storage/).
To manually configure MPIO on a host server, see the Dell Best Practices document that corresponds to the server operating system. Depending on the operating system, you may need to install MPIO software or configure server options.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\