Table below
lists in alphabetical order each line item that may appear in the
event description.
-
Description Line Item
-
Action performed was: <Action>
-
Explanation
- Specifies the action that was performed, for example:
Action performed was: Power cycle
-
Description Line Item
-
Action requested was: <Action>
-
Explanation
- Specifies the action that was requested, for example:
Action requested was: Reboot, shutdown OS first
-
Description Line Item
-
Additional Details: <Additional details for the event>
-
Explanation
- Specifies additional details available for the hot plug event,
for example:
Memory device: DIMM1_A Serial number: FFFF30B1
-
Description Line Item
-
<Additional power supply status information>
-
Explanation
- Specifies information pertaining to the event, for example:
Power supply input AC is off, Power supply POK (power OK) signal
is not normal, Power supply is turned off
-
Description Line Item
-
Chassis intrusion state: <Intrusion state>
-
Explanation
- Specifies whether the chassis intrusion state is
Open or
Closed. For example:
Chassis intrusion state: Open
-
Description Line Item
-
Chassis location: <Name of chassis>
-
Explanation
- Specifies name of the chassis that generated the message, for
example:
Chassis location: Main System Chassis
-
Description Line Item
-
Configuration error type: <type of configuration error>
-
Explanation
- Specifies the type of configuration error that occurred, for example:
Configuration error type: Revision mismatch
-
Description Line Item
-
Current sensor value (in Amps): <Reading>
-
Explanation
- Specifies the current sensor value in amps, for example:
Current sensor value (in Amps): 7.853
-
Description Line Item
-
Date and time of action: <Date and time>
-
Explanation
- Specifies the date and time the action was performed, for example:
Date and time of action: Sat Jun 12 16:20:33 2004
-
Description Line Item
-
Device location: <Location in chassis>
-
Explanation
- Specifies the location of the device in the specified chassis,
for example:
Device location: Memory Card A
-
Description Line Item
-
Discrete current state: <State>
-
Explanation
- Specifies the state of the current sensor, for example:
Discrete current state: Good
-
Description Line Item
-
Discrete temperature state: <State>
-
Explanation
- Specifies the state of the temperature sensor, for example:
Discrete temperature state: Good
-
Description Line Item
-
Discrete voltage state: <State>
-
Explanation
- Specifies the state of the voltage sensor, for example:
Discrete voltage state: Good
-
Description Line Item
-
Fan sensor value: <Reading>
-
Explanation
- Specifies the fan speed in revolutions per minute (RPM) or On/Off,
for example:
Fan sensor value (in RPM): 2600
Fan sensor value: Off
-
Description Line Item
-
Log type: <Log type>
-
Explanation
- Specifies the type of hardware log, for example:
Log type:
ESM
-
Description Line Item
-
Memory device bank location: <Bank name in chassis>
-
Explanation
- Specifies the name of the memory bank in the system that generated
the message, for example:
Memory device bank location: Bank_1
-
Description Line Item
-
Memory device location: <Device name in chassis>
-
Explanation
- Specifies the location of the memory module in the chassis, for
example:
Memory device location: DIMM_A
-
Description Line Item
-
Number of devices required for full redundancy: <Number>
-
Explanation
- Specifies the number of power supply or cooling devices required
to achieve full redundancy, for example:
Number of devices
required for full redundancy: 4
-
Description Line Item
-
Peak value (in Watts):<Reading>
-
Explanation
- Specifies the peak value in Watts, for example:
Peak value
(in Watts): 1.693
-
Description Line Item
-
Possible memory module event cause: <list of causes>
-
Explanation
- Specifies a list of possible causes for the memory module event,
for example:
Possible memory module event cause:
Single bit warning error rate exceeded
Single bit error logging disabled
-
Description Line Item
-
Power Supply type: <type of power supply>
-
Explanation
- Specifies the type of power supply, for example:
Power
Supply type: VRM
-
Description Line Item
-
Previous redundancy state was: <State>
-
Explanation
- Specifies the status of the previous redundancy message, for example:
Previous redundancy state was: Lost
-
Description Line Item
-
Previous state was:<State>
-
Explanation
- Specifies the previous state of the sensor, for example:
Previous state was: OK (Normal)
-
Description Line Item
-
Processor sensor status: <status>
-
Explanation
- Specifies the status of the processor sensor, for example:
Processor sensor status: Configuration error
-
Description Line Item
-
Redundancy unit: <Redundancy location in chassis>
-
Explanation
- Specifies the location of the redundant power supply or cooling
unit in the chassis, for example:
Redundancy unit: Fan Enclosure
-
Description Line Item
-
SD card device type: <Type of SD card device>
-
Explanation
- Specifies the type of SD card device, for example:
SD
card device type: Hypervisor
-
Description Line Item
-
SD card state: <State of SD card>
-
Explanation
- Specifies the state of the SD card, for example:
SD card
state: Present, Active
-
Description Line Item
-
Sensor location: <Location in chassis>
-
Explanation
- Specifies the location of the sensor in the specified chassis,
for example:
Sensor location: CPU1
-
Description Line Item
-
Temperature sensor value: <Reading>
-
Explanation
- Specifies the temperature in degrees Celsius, for example:
Temperature sensor value (in degrees Celsius): 30
-
Description Line Item
-
Voltage sensor value (in Volts):<Reading>
-
Explanation
- Specifies the voltage sensor value in volts, for example:
Voltage sensor value (in Volts): 1.693