Skip to main content
Sign Out

Welcome to Dell

My Account
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Create and access a list of your products
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.
Sign In Create an Account Premier Sign In Partner Program Sign In

Dell PowerEdge FN I/O Module Command Line Reference Guide 9.10(0.0)

PDF

seq

Configure a filter with an assigned sequence number for the redirect list.

Syntax seq sequence-number {permit | redirect { ip-address | tunnel tunnel-id}[track <obj-id>] }}{ ip-protocol-number | protocol-type} { source mask | any | host ip-address} { destination mask | any | host ip-address} [bit] [ operator]{source-port source-port| source-port-range start-port - end-port} {destination-port destination-port| destination-port-range start-port - end-port}

To delete a filter, use the no seq sequence-number command.

Parameters
sequence-number Enter a number from 1 to 65535.
permit Enter the keyword permit assign the sequence to the permit list.
redirect Enter the keyword redirect to assign the sequence to the redirect list.
ip-address Enter the IP address of the forwarding router.
tunnel Enter the keyword tunnel to configure the tunnel setting.
tunnel-id Enter the keyword tunnel-id to redirect the traffic.
track Enter the keyword track to enable the tracking.
track <obj-id> Enter the keyword track <obj-id> to track object-id.
ip-protocol-number Enter the keyword ip-protocol-number then the number from 0 to 255 for the protocol identified in the IP protocol header.
protocol-type Enter one of the following keywords as the protocol type:
  • icmp for internet control message protocol
  • ip for any internet protocol
  • tcp for transmission control protocol
  • udp for user datagram protocol
source Enter the IP address of the network or host from which the packets were sent.
mask Enter a network mask in /prefix format (/x).
any Enter the keyword any to specify that all traffic is subject to the filter.
host ip-address Enter the keyword host then the IP address to specify a host IP address.
destination Enter the IP address of the network or host to which the packets are sent.
bit (OPTIONAL) For the TCP protocol type only, enter one or a combination of the following TCP flags:
  • ack = acknowledgement
  • fin = finish (no more data from the user)
  • psh = push function
  • rst = reset the connection
  • syn = synchronize sequence number
  • urg = urgent field
operator (OPTIONAL) For the TCP and UDP parameters only. Enter one of the following logical operand:
  • eq = equal to
  • neq = not equal to
  • gt = greater than
  • lt= less than
  • range = inclusive range of ports (you must specify two ports for the port command parameter.)
source port Enter the keywords source-port then the port number to be matched in the ACL rule in the ICAP rule
destination-port Enter the keywords destination-port then the port number to be matched in the ACL rule in the ICAP rule.
source-port-range Enter the keywords Source-port-range then the range of the start port to end port to be matched in the ACL rule in the ICAP rule.
destination-port-range Enter the keywords destination-port-range then the range of the start port to end port to be matched in the ACL rule in the ICAP rule.
Defaults none
Command Modes REDIRECT-LIST
Supported Modes Full—Switch
Command History
Version Description
9.9(0.0) Introduced on the FN IOM.
9.7(0.0) Added support for the track-id on the MXL.
9.4(0.0) Added support for removing the Sonet interface on the MXL 10/40GbE Switch IO Module.

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\