Dell EMC SmartFabric OS10 User Guide Release 10.5.1

PBR and VLT

When you configure PBR in a VLT setup, configure the same PBR rules on both VLT peers.

In the following example, traffic originates from A and is destined to B. The traffic is redirected to C using a PBR rule through the VLT port channel. When the VLT port channel interface goes down, the traffic still reaches C through VLTi.

SW1

VLAN configuration

• Create a VLAN and assign an IP address to it which acts as the gateway for the hosts in the VM.

  OS10# configure terminal
  OS10(config)# interface vlan 100
  OS10(conf-if-vl-100)# no shutdown
  OS10(conf-if-vl-100)# ip address 10.1.1.1/24
  OS10(conf-if-vl-100)# exit
  

• Create another VLAN, and assign an IP address to it.

  OS10# configure terminal
  OS10(config)# interface vlan 200
  OS10(conf-if-vl-200)# no shutdown
  OS10(conf-if-vl-200)# ip address 10.2.1.1/24
  OS10(conf-if-vl-200)# exit
  

VLT configuration

1. Create a VLT domain, and configure VLTi.

   OS10(config)# interface range ethernet 1/1/4-1/1/5
   OS10(conf-range-eth1/1/4-1/1/5)# no switchport
   OS10(conf-range-eth1/1/4-1/1/5)# exit
   OS10(config)# vlt-domain 1
   OS10(conf-vlt-1)# discovery-interface ethernet 1/1/4-1/1/5

2. Configure a VLT MAC address.

   OS10(conf-vlt-1)# vlt-mac 12:5e:23:2d:76:3e

3. Specify the management IP address of the VLT peer as a backup link.

   OS10(conf-vlt-1)# backup destination 10.10.10.2
   

4. Configure VLT port channels.

   SW1-to-VM VLT port channel configuration

   OS10(config)# interface port-channel 10
   OS10(conf-if-po-10)# description SW1ToVM
   OS10(conf-if-po-10)# vlt-port-channel 10
   OS10(conf-if-po-10)# switchport mode trunk
   OS10(conf-if-po-10)# switchport trunk allowed vlan 100,200
   OS10(conf-if-po-10)# exit
   OS10(config)# interface range ethernet 1/1/2-1/1/3
   OS10(conf-if-eth1/1/2-1/1/3)# no shutdown
   OS10(conf-if-eth1/1/2-1/1/3)# channel-group 10
   

   SW1-to-server configuration

   OS10(config)# interface port-channel 20
   OS10(conf-if-po-20)# description SW1ToServer
   OS10(conf-if-po-20)# vlt-port-channel 20
   OS10(conf-if-po-20)# switchport mode trunk
   OS10(conf-if-po-20)# switchport trunk allowed vlan 100,200
   OS10(conf-if-po-20)# exit
   OS10(config)# interface range ethernet 1/1/1,1/1/6
   OS10(conf-if-eth1/1/1,1/1/6)# no shutdown
   OS10(conf-if-eth1/1/1,1/1/6)# channel-group 20
   

(Optional) Peer routing configuration

• Configure peer routing.

  OS10(config)# vlt-domain 1
  OS10(conf-vlt-1)# peer-routing

PBR configuration

Apply the policy on the traffic ingress interface and the VLTi interfaces of both VLT peers.

OS10(config)# ip access-list PBR-A2C
OS10(conf-ipv4-acl)# permit ip 10.10.10.0/24 any
OS10(config-ipv4-acl)# exit
OS10(config)# route-map Map1
OS10(conf-route-map)# match ip address PBR-A2C
OS10(conf-route-map)# set ip next-hop 10.10.20.10
OS10(conf-route-map)# exit
OS10(config)# interface range ethernet 1/1/4-1/1/6
OS10(conf-if-eth1/1/4-1/1/6)# ip policy route-map Map1

SW2

VLAN configuration

• Create a VLAN and assign an IP address to it which acts as the gateway for the hosts in the VM.

  OS10# configure terminal
  OS10(config)# interface vlan 100
  OS10(conf-if-vl-100)# no shutdown
  OS10(conf-if-vl-100)# ip address
  OS10(conf-if-vl-100)# ip address 10.1.1.2/24
  OS10(conf-if-vl-100)# exit
  

• Create another VLAN, and assign an IP address to it.

  OS10# configure terminal
  OS10(config)# interface vlan 200
  OS10(conf-if-vl-200)# no shutdown
  OS10(conf-if-vl-200)# ip address
  OS10(conf-if-vl-200)# ip address 10.2.1.3/24
  OS10(conf-if-vl-200)# exit
  

VLT configuration

1. Create a VLT domain, and configure VLTi.

   OS10(config)# interface range ethernet 1/1/4-1/1/5
   OS10(conf-range-eth1/1/4-1/1/5)# no switchport
   OS10(conf-range-eth1/1/4-1/1/5)# exit
   OS10(config)# vlt-domain 1
   OS10(conf-vlt-1)# discovery-interface ethernet 1/1/4-1/1/5

2. Configure a VLT MAC address.

   OS10(conf-vlt-1)# vlt-mac 12:5e:23:f4:23:54

3. Specify the management IP address of the VLT peer as a backup link.

   OS10(conf-vlt-1)# backup destination 10.10.10.1
   

4. Configure VLT port channels.

   SW2-to-VM VLT port channel configuration

   OS10(config)# interface port-channel 10
   OS10(conf-if-po-10)# description SW2ToVM
   OS10(conf-if-po-10)# vlt-port-channel 10
   OS10(conf-if-po-10)# switchport mode trunk
   OS10(conf-if-po-10)# switchport trunk allowed vlan 100,200
   OS10(conf-if-po-10)# exit
   OS10(config)# interface range ethernet 1/1/2-1/1/3
   OS10(conf-if-eth1/1/2-1/1/3)# no shutdown
   OS10(conf-if-eth1/1/2-1/1/3)# channel-group 10
   

( Optional) Peer routing configuration

• Configure peer routing.

  OS10(config)# vlt-domain 1
  OS10(conf-vlt-1)# peer-routing

PBR configuration

Apply the policy on the VLTi interfaces of both VLT peers.

OS10(config)# ip access-list PBR-A2C
OS10(conf-ipv4-acl)# permit ip 10.10.10.0/24 any
OS10(conf-route-map)# route-map Map1
OS10(conf-route-map)# match ip address PBR-A2C
OS10(conf-route-map)# set ip next-hop 10.10.20.10
OS10(conf-route-map)# exit
OS10(config)# interface ethernet 1/1/4-1/1/6
OS10(conf-if-eth1/1/4-1/1/6)# ip policy route-map Map1