Dell PowerVault ME5 Series Administrator's Guide

Settings changed by restoring defaults

This table summarizes the system settings that result from using the restore defaults CLI command.


Setting	Value
System information settings
System name	Uninitialized Name
System contact	Uninitialized Contact
System location	Uninitialized Location
Management protocols settings
CLI/Telnet	Disabled
CLI/SSH	Enabled
SLP	Enabled
FTP	Disabled
SFTP	Enabled
SNMP	Disabled
WBI/HTTP	Disabled
WBI/HTTPS	Enabled
Debug	Disabled
Ciphers setting	Default cipher strings
CLI session timeout	Preserved
Users	All configured users are deleted and replaced with default user definitions and default settings: User: setup ; Password: press Enter
Tasks and schedules	Preserved
Debug log settings
Management Controller debug logs	Preserved
Management Controller event logs	Preserved
Storage Controller debug logs	Preserved
Storage Controller event logs	Preserved
Network settings
Time/date and NTP settings	Preserved
Network IP settings	Preserved
IPv6 network settings	Preserved
DNS management hostname	Preserved
DNS name servers	Preserved
DNS search domains	Preserved
SNMP settings
SNMP trap notification level	None
SNMP trap host IPs	0.0.0.0
SNMP read community	public
SNMP write community	private
SMTP settings
Email notification	Disabled
Email notify filter	None
Email addresses	None
Email server	None
Email domain	None
Email sender	None
Log destination	None
Include logs	Disabled
Alert notification	All
Proxy setting	Cleared
LDAP
LDAP parameters	Cleared
LDAP settings	Disabled (server IP defaulted to 0.0.0.0)
User groups	Preserved
Audit log	Preserved
Syslog
Sylog parameters	Cleared
Syslog settings	Disabled (host IP defaulted to 0.0.0.0)
Alert settings
Alert condition history	Preserved
Alerts	Preserved
SSL/SSH certificates	Preserved
Host port settings
FC link speed	Auto
FC topology	Point-to-point
Disk settings
Disk group metadata	Preserved
Disk spin down	Disabled
Advanced settings
Disk group background scrub	Enabled
Disk group background scrub interval	24 hours
Partner firmware upgrade	Enabled
Utility priority	High
SMART	Enabled
Dynamic spare configuration	Enabled
Enclosure polling rate	5 seconds
Host control of caching	Disabled
Sync cache mode	Immediate
Missing LUN response	Not Ready
Controller failure	Disabled
Supercap failure	Enabled
Power supply failure	Disabled
Fan failure	Disabled
Temperature exceeded	Disabled
Partner notify	Disabled
Auto write back	Enabled
Inactive drive spin down	Disabled
Inactive drive spin down delay	15 minutes
Disk background scrub	Disabled
Managed logs	Disabled
Single controller mode	Disabled
Auto stall recovery	Enabled (for failover/failback, not I/O)
Restart on CAPI fail	Enabled
FDE settings	Preserved
Replication settings
Peer connections	Preserved
Replication sets	Preserved
CHAP records	Preserved
Enclosure settings
Name	Cleared
Location	Cleared
Rack number	0
Rack position	0.0.0.0
iSCSI port settings
IP	Preserved
IP version	Preserved
Netmask	Preserved
Gateway	Preserved
Router (IPv6 only)	Preserved
Other iSCSI settings
CHAP enabled	Preserved
iSNS	Preserved
Jumbo frames	Preserved
Host settings
Host and initiator nicknames and profiles	Preserved
Host groups	Preserved
Host port mode	Preserved
Volume settings
Volume identifying information	Preserved
Volume groups	Preserved
Pool settings
Thresholds	Preserved
Overcommit	Preserved
Limits and policy	Preserved
Snapshot space thresholds	Preserved
Miscellaneous settings
CLI parameters	CLI parameters are kept on a per-user basis. All configured users are deleted and replaced with default user definitions and default settings as detailed in the Users section of this table.
Debug log parameters	Each parameter is reset to its default as documented for the set debug-log-parameters CLI command.
Volume snapshot retention priority	Preserved
Volume cache settings	Preserved
Expander PHY settings	Controller module root expander PHY settings are cleared
Volume tier affinity	Preserved
Device identification LED status	Preserved