- Notes, cautions, and warnings
- Overview
- Physical Disks
- Virtual Disks
- Cabling the drives for S130
- BIOS Configuration Utility
- Entering the BIOS Configuration Utility
- Exiting the BIOS Configuration Utility
- Initializing the physical disks
- Creating the virtual disks
- Deleting the virtual disks
- Swapping two virtual disks
- Managing the hot spare disks
- Viewing the physical disks details
- Viewing the virtual disks details
- Rescanning the disks
- Controller Options
- Continue to boot
- UEFI RAID configuration utility
- Installing the drivers
- Pre-installation requirements
- Creating the device driver media for Windows driver installation
- Installing the driver for Windows Server 2008 R2 or Windows Server 2012/2012 R2
- Updating the existing driver for Windows Server 2008 or Windows Server 2012/2012 R2
- Installing the driver for Windows Server 2016
- Troubleshooting your system
- Unable to create a new partition while installing Windows 2012/2012 R2 operating system
- 0x0000003B or 0x0000007E stop error occurs on a system while using a 4K sector disks
- Performance degradation after disabling physical disk write cache policy
- Unable to modify any feature settings in UEFI or OPROM
- Unable to recover the crash dump file when the operating system fails
- System startup issues
- System does not boot
- Controller mode is set incorrectly at System Setup
- Boot mode, boot sequence, and or boot sequence retry are set incorrectly
- Bootable virtual disk is in a failed state
- The boot order is incorrect for a bootable virtual disk
- A Non-RAID virtual disk is no longer in the first position in the BIOS Configuration Utility (<Ctrl><R>) list after the system is rebooted
- The BIOS Configuration Utility (<Ctrl><R>) option does not display
- Warning Message
- Other errors appearing on the BIOS screen
- Physical disk - related errors
- Virtual disks - related errors
- Rebuilding a virtual disk the global hot spare is not listed as online in HII or iDRAC
- Cannot create a virtual disk
- Rebuilding a virtual disk the global hot spare is not listed as online in HII or iDRAC
- The physical disk is not displayed
- Insufficient free space available on the selected physical disks
- Incorrect number of physical disks selected for the desired RAID level
- The desired physical disk is unavailable
- The system already has a maximum of eight virtual disks
- A virtual disk is in a failed state
- A virtual disk is in a degraded state
- Cannot assign a dedicated hot spare to a virtual disk
- Cannot create a global hot spare
- A dedicated hot spare fails
- Failed or degraded virtual disk
- Cannot create a virtual disk on selected physical disks
- Cannot perform an Online Capacity Expansion or Reconfigure on a virtual disk
- Getting help
Benvenuto
Benvenuto in Dell
Il mio account
- Effettua gli ordini in modo rapido e semplice
- Visualizza gli ordini e monitora lo stato della spedizione
- Crea e accedi a un elenco dei tuoi prodotti
- Gestisci i siti, i prodotti e i contatti per livello di prodotto di Dell EMC tramite l'amministrazione della società.
Dell EMC PowerEdge RAID Controller S130 User’s Guide
Assigning the dedicated hot spare
- Enter the Dell PERC S130 Configuration Utility. See Entering the DELL PERC S130 Configuration Utility.
- Click .
NOTE: Assign dedicated hot spare only from disk drives populated across slots 0-3 of the system. For information about the disk connectivity for AHCI devices, see Disk connectivity for AHCI devices,and for disks slot information, see the system specific Owner's Manual at dell.com/poweredgemanuals.
- Select the physical disk that is in the ready state from the drop-down menu.
- Click the link Add Hot Spare Disk.
Fornisci una valutazione (1-5 stelle).
Fornisci una valutazione (1-5 stelle).
Fornisci una valutazione (1-5 stelle).
Indica se l'articolo è stato utile o meno.
I commenti non possono contenere i seguenti caratteri speciali: <>() \