- Notes, cautions, and warnings
- Overview
- Physical Disks
- Virtual Disks
- Cabling the drives for S130
- BIOS Configuration Utility
- Entering the BIOS Configuration Utility
- Exiting the BIOS Configuration Utility
- Initializing the physical disks
- Creating the virtual disks
- Deleting the virtual disks
- Swapping two virtual disks
- Managing the hot spare disks
- Viewing the physical disks details
- Viewing the virtual disks details
- Rescanning the disks
- Controller Options
- Continue to boot
- UEFI RAID configuration utility
- Installing the drivers
- Pre-installation requirements
- Creating the device driver media for Windows driver installation
- Installing the driver for Windows Server 2008 R2 or Windows Server 2012/2012 R2
- Updating the existing driver for Windows Server 2008 or Windows Server 2012/2012 R2
- Installing the driver for Windows Server 2016
- Troubleshooting your system
- Unable to create a new partition while installing Windows 2012/2012 R2 operating system
- 0x0000003B or 0x0000007E stop error occurs on a system while using a 4K sector disks
- Performance degradation after disabling physical disk write cache policy
- Unable to modify any feature settings in UEFI or OPROM
- Unable to recover the crash dump file when the operating system fails
- System startup issues
- System does not boot
- Controller mode is set incorrectly at System Setup
- Boot mode, boot sequence, and or boot sequence retry are set incorrectly
- Bootable virtual disk is in a failed state
- The boot order is incorrect for a bootable virtual disk
- A Non-RAID virtual disk is no longer in the first position in the BIOS Configuration Utility (<Ctrl><R>) list after the system is rebooted
- The BIOS Configuration Utility (<Ctrl><R>) option does not display
- Warning Message
- Other errors appearing on the BIOS screen
- Physical disk - related errors
- Virtual disks - related errors
- Rebuilding a virtual disk the global hot spare is not listed as online in HII or iDRAC
- Cannot create a virtual disk
- Rebuilding a virtual disk the global hot spare is not listed as online in HII or iDRAC
- The physical disk is not displayed
- Insufficient free space available on the selected physical disks
- Incorrect number of physical disks selected for the desired RAID level
- The desired physical disk is unavailable
- The system already has a maximum of eight virtual disks
- A virtual disk is in a failed state
- A virtual disk is in a degraded state
- Cannot assign a dedicated hot spare to a virtual disk
- Cannot create a global hot spare
- A dedicated hot spare fails
- Failed or degraded virtual disk
- Cannot create a virtual disk on selected physical disks
- Cannot perform an Online Capacity Expansion or Reconfigure on a virtual disk
- Getting help
Benvenuto
Benvenuto in Dell
Il mio account
- Effettua gli ordini in modo rapido e semplice
- Visualizza gli ordini e monitora lo stato della spedizione
- Crea e accedi a un elenco dei tuoi prodotti
- Gestisci i siti, i prodotti e i contatti per livello di prodotto di Dell EMC tramite l'amministrazione della società.
Dell EMC PowerEdge RAID Controller S130 User’s Guide
System does not boot
Check for
the following causes when the system does not boot:
Incorrect Controller Mode at the System Setup
Incorrect Boot Mode, Boot Sequence, and/or Boot Sequence Retry
Bootable virtual disk is in Failed state
Incorrect Boot Order for a bootable virtual disk
A Non-RAID virtual disk is no longer in the first position in the BIOS Configuration Utility (<Ctrl><R>) list after the system is rebooted
In the Linux RAID configuration, if virtual disks created exceed the maximum limit of 10 and the boot virtual disk is not listed as one of the 10 virtual disks in UEFI configuration utility.
Fornisci una valutazione (1-5 stelle).
Fornisci una valutazione (1-5 stelle).
Fornisci una valutazione (1-5 stelle).
Indica se l'articolo è stato utile o meno.
I commenti non possono contenere i seguenti caratteri speciali: <>() \