- Notes, cautions, and warnings
- Dell PowerEdge C4130 overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- Viewing System BIOS
- System BIOS Settings details
- Boot Settings
- Network Settings
- System Security
- System Information
- Memory Settings
- Processor Settings
- SATA Settings
- Integrated Devices
- Serial Communication
- System Profile Settings
- Miscellaneous Settings
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- System covers
- Inside the system - PowerEdge C4130
- Chassis intrusion switch
- IDSDM
- Cooling shroud
- Processor blank
- System memory
- Processors and heat sinks
- System battery
- PCIe shroud
- Expansion card riser and expansion cards
- Power supply units
- Hard drives
- Removing the optional 2.5 inch hard drive cage
- Installing the optional 2.5 inch hard drive cage
- Removing the optional 2.5 inch hard drive cage cover
- Installing the optional 2.5 inch hard drive cage cover
- Removing 2.5 inch cabled hard drives from the hard drive cage
- Installing a 2.5 inch cabled hard drive into the hard drive cage
- Hard drive cabling diagrams
- uSATA SSDs
- Removing a 1.8 inch uSATA SSD blank
- Installing a 1.8 inch uSATA SSD blank
- Removing a 1.8 inch uSATA SSD carrier
- Installing a 1.8 inch uSATA SSD carrier
- Removing a 1.8 inch uSATA SSD from a SSD carrier
- Installing a 1.8 inch uSATA SSD into a SSD carrier
- Removing the 1.8 inch uSATA SSD cage
- Installing the 1.8 inch uSATA SSD cage
- Removing the 1.8 inch uSATA SSD backplane
- Installing the 1.8 inch uSATA SSD backplane
- Internal USB memory key (optional)
- Cable routing clip
- System board
- Trusted Platform Module
- Cooling fans
- Graphics processing unit
- PCIe Graphics processing unit
- GPU installation guidelines
- Removing a GPU blank
- Removing a GPU riser cable from the system board
- Removing a GPU
- Removing a GPU riser cable board
- Removing the custom GPU brackets from the GPUs removed from your system
- Removing the GPU brackets from the replacement GPUs
- Removing the optional GPU switch board
- Installing the optional GPU switch board
- Installing the GPU brackets on the GPUs removed from your system
- Installing the custom GPU brackets on the replacement GPUs
- Installing a GPU riser cable board
- Installing a GPU blank
- Installing a GPU
- Installing a GPU riser cable on the system board
- GPU cabling diagrams
- SXM2 Graphics processing unit
- Control panel module
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Troubleshooting system startup failure
- Troubleshooting external connections
- Troubleshooting the video subsystem
- Troubleshooting a USB device
- Troubleshooting a serial input and output device
- Troubleshooting a NIC
- Troubleshooting a wet system
- Troubleshooting a damaged system
- Troubleshooting the system battery
- Troubleshooting power supply units
- Troubleshooting cooling problems
- Troubleshooting cooling fans
- Troubleshooting system memory
- Troubleshooting an internal USB key
- Troubleshooting a micro SD card
- Troubleshooting a drive or SSD
- Troubleshooting a storage controller
- Troubleshooting expansion cards
- Troubleshooting processors
- Troubleshooting a GPU
- System messages
- Getting help
Dell PowerEdge C4130 Owner's Manual
Recommended tools
You need the following tools to perform the removal and installation
procedures:
- Phillips #1 screwdriver
- Phillips #2 screwdriver
- Torx #T6 and #T10 screwdrivers
- Wrist grounding strap
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\