AirExhaustTemp |
Allows to set
the maximum air exhaust temperature limit. |
Set to any
of the following values (based on the system):
- 0 - Indicates 40°C
- 1 - Indicates 45°C
- 2 - Indicates 50°C
- 3 - Indicates 55°C
- 4 - Indicates 60°C
- 255 - Indicates 70°C (default)
|
To check the
existing setting on the system:racadm get system.thermalsettings.AirExhaustTemp The output is: AirExhaustTemp=70 This
means that the system is set to limit the air exhaust temperature
to 70°C. To set the exhaust temperature limit to 60°C: racadm set system.thermalsettings.AirExhaustTemp 4 The output is: Object value modified successfully. If a system does not support a particular air exhaust temperature
limit, then when you run the following command: racadm set system.thermalsettings.AirExhaustTemp 0 The following error message is displayed: ERROR: RAC947: Invalid object value specified. Make sure to specify the value depending on the type of object. For more information, see RACADM help. To set the limit
to the default value: racadm set system.thermalsettings.AirExhaustTemp 255 |
FanSpeedHighOffsetVal |
- Getting this variable reads the fan speed offset value in %PWM
for High Fan Speed Offset setting.
- This value depends on the system.
- Use FanSpeedOffset object to set this value using
index value 1.
|
Values from
0-100 |
racadm get system.thermalsettings FanSpeedHighOffsetVal This returns a value such as “66”. This means that when you use
the following command, it applies a fan speed offset of High (66%
PWM) over the baseline fan speed racadm set system.thermalsettings FanSpeedOffset 1 |
FanSpeedLowOffsetVal |
- Getting this variable reads the fan speed offset value in %PWM
for Low Fan Speed Offset setting.
- This value depends on the system.
- Use FanSpeedOffset object to set this value using
index value 0.
|
Values from
0-100 |
racadm get system.thermalsettings FanSpeedLowOffsetVal This returns a value such as “23”. This means that when you use
the following command, it applies a fan speed offset of Low (23%
PWM) over baseline fan speed racadm set system.thermalsettings FanSpeedOffset 0 |
FanSpeedMaxOffsetVal |
- Getting this variable reads the fan speed offset value in %PWM
for Max Fan Speed Offset setting.
- This value depends on the system.
- Use FanSpeedOffset to set this value using index
value 3
|
Values from
0-100 |
racadm get system.thermalsettings FanSpeedMaxOffsetVal This returns a value such as “100”. This means that when you use
the following command, it applies a fan speed offset of Max (meaning
full speed, 100% PWM). In most cases, this offset results in fan speeds
increasing to full speed. racadm set system.thermalsettings FanSpeedOffset 3 |
FanSpeedMediumOffsetVal |
- Getting this variable reads the fan speed offset value in %PWM
for Medium Fan Speed Offset setting.
- This value depends on the system.
- Use FanSpeedOffset object to set this value using
index value 2
|
Values from
0-100 |
racadm get system.thermalsettings FanSpeedMediumOffsetVal This returns a value such as “47”. This means that when you use
the following command, it applies a fan speed offset of Medium (47%
PWM) over baseline fan speed racadm set system.thermalsettings FanSpeedOffset 2 |
FanSpeedOffset |
- Using this object with get command displays the existing Fan Speed
Offset value.
- Using this object with set command allows setting the required
fan speed offset value.
- The index value decides the offset that is applied and the FanSpeedLowOffsetVal, FanSpeedMaxOffsetVal, FanSpeedHighOffsetVal, and FanSpeedMediumOffsetVal objects (defined earlier) are the values at which the offsets are
applied.
|
Values are:
- 0 - Low Fan Speed
- 1 - High Fan Speed
- 2 - Medium Fan Speed
- 3 - Max Fan Speed
- 255 - None
|
To view
the existing setting: racadm get system.thermalsettings.FanSpeedOffset To set the fan speed offset to High value (as defined in FanSpeedHighOffsetVal) racadm set system.thermalsettings.FanSpeedOffset 1 |
MFSMaximumLimit |
Read Maximum
limit for MFS |
Values from
1 - 100 |
To display
the highest value that can be set using MinimumFanSpeed option: racadm get system.thermalsettings.MFSMaximumLimit |
MFSMinimumLimit |
Read Minimum
limit for MFS |
Values from
0 to MFSMaximumLimit Default is 255 (means
None) |
To display
the lowest value that can be set using MinimumFanSpeed option. racadm get system.thermalsettings.MFSMinimumLimit |
MinimumFanSpeed |
- Allows configuring the Minimum Fan speed that is required for
the system to operate.
- It defines the baseline (floor) value for fan speed and system
allows fans to go lower than this defined fan speed value.
- This value is %PWM value for fan speed.
|
Values from MFSMinimumLimit to MFSMaximumLimit When get command reports 255, it means user configured offset is
not applied. |
To make
sure that the system minimum speed does not decrease lower than 45%
PWM (45 must be a value between MFSMinimumLimit to MFSMaximumLimit): racadm set system.thermalsettings.MinimumFanSpeed 45 |
ThermalProfile |
- Allows to specify the Thermal Base Algorithm.
- Allows to set the system profile as required for thermal behavior
associated to the profile.
|
Values:
- 0 — Auto
- 1 — Maximum performance
- 2 — Minimum Power
|
To view
the existing thermal profile setting: racadm get system.thermalsettings.ThermalProfile To set the thermal profile to Maximum Performance: racadm set system.thermalsettings.ThermalProfile 1 |