Omitir para ir al contenido principal
Cerrar

Bienvenido a Dell

Mi cuenta
  • Hacer pedidos rápida y fácilmente
  • Ver pedidos y realizar seguimiento al estado del envío
  • Cree y acceda a una lista de sus productos
  • Administre sus sitios, productos y contactos de nivel de producto de Dell EMC con Administración de la empresa.
Iniciar sesión Crear una cuenta Clientes Premier Iniciar sesión en el programa para partners
Contáctenos

Dell PowerEdge FN I/O Module Configuration Guide 9.10(0.0)

PDF

VLAN Configuration on Physical Ports and Port-Channels

Unlike other Dell Networking OS platforms, IOA allows VLAN configurations on port and port-channel levels. This allows you to assign VLANs to a port/port-channel.
  • NOTE: In PMUX mode, in order to avoid loops, only disjoint VLANs are allowed between the uplink ports/uplink LAGs and uplink-to-uplink switching is disabled.
  1. Initialize the port with configurations such as admin up, portmode, and switchport. 
    Dell#configure
                                    Dell(conf)#int tengigabitethernet 0/1
                                    Dell(conf-if-te-0/1)#no shutdown
                                    Dell(conf-if-te-0/1)#portmode hybrid
                                    Dell(conf-if-te-0/1)#switchport
  2. Configure the tagged VLANs 10 through 15 and untagged VLAN 20 on this port. 
    Dell(conf-if-te-0/1)#vlan tagged 10-15
                                    Dell(conf-if-te-0/1)#vlan untagged 20
                                    Dell(conf-if-te-0/1)#
  3. Show the running configurations on this port. 
    Dell(conf-if-te-0/1)#show config
                                    !
                                    interface TenGigabitEthernet 0/1
                                    portmode hybrid
                                    switchport
                                    vlan tagged 10-15
                                    vlan untagged 20
                                    no shutdown
                                    Dell(conf-if-te-0/1)#end
                                    Dell#
  4. Initialize the port-channel with configurations such as admin up, portmode, and switchport. 
    Dell#configure
                                    Dell(conf)#int port-channel 128
                                    Dell(conf-if-po-128)#portmode hybrid
                                    Dell(conf-if-po-128)#switchport
  5. Configure the tagged VLANs 10 through 15 and untagged VLAN 20 on this port-channel. 
    Dell(conf-if-po-128)#vlan tagged 10-15
                                    Dell(conf-if-po-128)#
                                    Dell(conf-if-po-128)#vlan untagged 20
  6. Show the running configurations on this port-channel. 
    Dell(conf-if-po-128)#show config
                                    !
                                    interface Port-channel 128
                                    portmode hybrid
                                    switchport
                                    vlan tagged 10-15
                                    vlan untagged 20
                                    shutdown
                                    Dell(conf-if-po-128)#end
                                    Dell#
  7. Show the VLAN configurations. 
    Dell#show vlan
                                    Codes: * - Default VLAN, G - GVRP VLANs, R - Remote Port 
                                    Mirroring VLANs, P - Primary, C - Community, I - Isolated
                                    			O - Openflow
                                    Q: U - Untagged, T - Tagged
                                    x - Dot1x untagged, X - Dot1x tagged
                                    o - OpenFlow untagged, O - OpenFlow tagged
                                    G - GVRP tagged, M - Vlan-stack, H - VSN tagged
                                    i - Internal untagged, I - Internal tagged, v - VLT 
                                    untagged, V - VLT tagged
                                    
                                    	NUM 	Status 	 Description 	Q 	Ports
                                    * 1 	   Active  						U Te 0/3 
                                    10		Active							T Po128(Te 0/4-5)
                                    												T Te 0/1  
                                    11		Active							T Po128(Te 0/4-5)
                                    12 	Active 							T Po128(Te 0/4-5)
                                    												T Te 0/1
                                    13		Active 							T Po128(Te 0/4-5)
                                    												T Te 0/1
                                    14 	Active 							T Po128(Te 0/4-5)
                                    												T Te 0/1
                                    15 	Active 							T Po128(Te 0/4-5)
                                    												T Te 0/1 
                                    20 	Active 							U Po128(Te 0/4-5)
                                    												U Te 0/1
                                    Dell#

    You can remove the inactive VLANs that have no member ports using the following command: 

    Dell#configure
                                       Dell(conf)#no interface vlan 
                                       vlan-id
    vlan-id — Inactive VLAN with no member ports

    You can remove the tagged VLANs using the no vlan tagged vlan-range command. You can remove the untagged VLANs using the no vlan untagged command in the physical port/port-channel.

Califique este contenido

Preciso
Útil
Fácil de comprender
¿Este artículo fue útil?
0/3000 characters
  Proporcione calificaciones (1 a 5 estrellas).
  Proporcione calificaciones (1 a 5 estrellas).
  Proporcione calificaciones (1 a 5 estrellas).
  Seleccione si el artículo fue útil o no.
  Los comentarios no pueden contener estos caracteres especiales: <>"(", ")", "\"