Event and Error Message Reference Guide For 13th Generation Dell PowerEdge Servers Version 1.0

RAC001

Message: The command was successful.
Detailed Description: The command was successful.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC002

Message: General failure.
Detailed Description: An unknown error occurred.
Recommended Response Action: Do one of the following: 1) Rerun the command. 2) Reset iDRAC and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC003

Message

Missing required parameter arg1 .

Arguments

arg1 = parameter name

Detailed Description

One or more required parameters for the method are missing.

Recommended Response Action

Refer to the profile document and provide the required parameters.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC004

Message

Invalid parameter value for arg1 .

Arguments

arg1 = parameter

Detailed Description

The parameter value for the given parameter is invalid.

Recommended Response Action

Provide a valid parameter value for specified parameter.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC005

Message: Mismatch in AttributeName and AttributeValue count.
Detailed Description: The name value pairs do not match in the input specified in the method invocation parameters.
Recommended Response Action: Provide a valid (AttributeName, AttributeValue) pair.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC006

Message: AttributeValue cannot be changed for ReadOnly Attribute Name
Detailed Description: The Attribute attempted to be set is ReadOnly and hence cannot be changed in value</div>
Recommended Response Action: Set an Attribute that is not ReadOnly.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC007

Message: Input out of Range
Detailed Description: <div>The attribute value is outside the acceptable range for the given attribute</div>
Recommended Response Action: <div>Try a value within the acceptable range of the attribute. Check the documentation for reference.</div>
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC008

Message: Invalid boolean Value
Detailed Description: The attribute boolean value is not valid for the specified attribute.
Recommended Response Action: Provide valid boolean value for the specified attribute.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC009

Message: String exceeds maximum length.
Detailed Description: Length of string for AttributeName has exceeded the maximum length allowed.
Recommended Response Action: Verify the string length and retry the operation. Refer to the Lifecycle Controller-Remote Services documentation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC010

Message: Invalid character value.
Detailed Description: The input value for the attribute being set contains characters that are not allowed.
Recommended Response Action: Retry the operation with valid characters for the specified attribute. Refer to the Lifecycle Controller-Remote Services documentation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0100

Message: The Smart Card is removed. Further communication is not possible.
Detailed Description: Communication with the Smart Card has been lost.
Recommended Response Action: Insert a valid Smart Card and try again.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0101

Message: The inserted Smart Card is not valid or the Smart Card reader is not supported.
Detailed Description: The data returned is not in a known format.
Recommended Response Action: This error may occur because: 1. Smart Card is invalid. Insert a valid Smart Card and try again. 2. Check connection between reader and system. 3. There may be an issue with the Smart Card reader. Try reinstalling the reader driver or use a different reader.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0102

Message: The Smart Card Logon plug-in is not installed. Install the plug-in from the iDRAC Web GUI to log in using Smart Card.
Detailed Description: The software to communicate with the Smart Card is not loaded in this browser. Smart Card can be used for log in only if the appropriate Smart Card software is installed in the browser.
Recommended Response Action: Install the plug-in prompted by the iDRAC Web GUI to log in using Smart Card.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0103

Message: This browser does not support Smart Card logon on iDRAC. Use Internet Explorer version 7.0 or later to use this feature.
Detailed Description: Smart Card login is only supported in newer versions of Internet Explorer.
Recommended Response Action: See the iDRAC help text or documentation for a list of supported browsers.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0104

Message: An incorrect PIN was entered.
Detailed Description: An invalid PIN was entered. Too many log in attempts with a Smart Card login can result in a user being locked out of the system.
Recommended Response Action: 1. Enter a valid Smart Card PIN and try again. 2. Use a different Smart Card.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0105

Message: The Smart Card reader cannot be detected. Check whether the reader is installed correctly.
Detailed Description: Communication with the Smart Card reader cannot be established, or is lost.
Recommended Response Action: This error may occur because: 1. Check connection between reader and system. 2. There may be an issue with the Smart Card reader. Try reinstalling the reader driver or use a different reader.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0106

Message: The Smart Card cannot be detected. Insert the Smart Card correctly.
Detailed Description: Communication with the Smart Card reader is established and a Smart Card is inserted, but there are problems reading the Smart Card.
Recommended Response Action: This error may occur because: 1. Make sure the Smart Card is seated correctly. 2. Smart Card is invalid. Insert a valid Smart Card and try again. 3. Check connection between reader and system. 4. There may be an issue with the Smart Card reader. Try reinstalling the reader driver or use a different reader.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0107

Message: The inserted Smart Card cannot be recognized. Ensure that the correct Smart Card CSP drivers are installed.
Detailed Description: Communication with the Smart Card reader is established and a Smart Card is inserted, but there are problems accessing the Smart Card. The appropriate Cryptographic Service Provider (CSP) drivers are not installed.
Recommended Response Action: There may be an issue with the Smart Card Cryptographic Service Provider (CSP) drivers. Use the client OS to install CSP driver. If the OS has problem with Smart Card, then there will have problem using the Smart Card. So make sure Smart Card can login with Windows OS.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0108

Message: An internal error is encountered. Insert a valid Smart Card and try again. (Does this and preceeding messages show up in the SEL?)
Detailed Description: A non-specific error is detected when accessing the Smart Card.
Recommended Response Action: Review the error message preceeding or following this message.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC011

Message: Job already exists, cannot process more set operations.
Detailed Description: Job has already been scheduled to apply pending iDRAC attribute values.
Recommended Response Action: Wait for the scheduled job to complete before setting more attributes.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0113

Message: Remote Syslog Port value is invalid: Valid range is 1-65535 or 0x1-0xFFFF.
Detailed Description: Data entered is not an integer value in the valid range of numbers.
Recommended Response Action: Enter a Remote Syslog Port number. Expected range: [1-65535 or 0x1-0xFFFF]
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0115

Message: The Destination IP Address value is invalid.
Detailed Description: The IPv4 address does not conform to the addressing standard or the supported IPv4 address range.
Recommended Response Action: Enter the Destination IP Address value between [1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0116

Message: Invalid Destination IPv6 Address.
Detailed Description: The entered IPv6 address does not conform to the addressing standard or the supported IPv6 address range.
Recommended Response Action: Enter a valid Destination IPv6 Address.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0117

Message: SD card is unavailable.
Detailed Description: The SD card is not present, or communication with the SD card is lost. This could result in reduced functionality and capabilities.
Recommended Response Action: This error may occur because: 1. Make sure the SD card is seated correctly. 2. The SD card is invalid. Insert a valid SD card of size greater than 256MB and try again.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0118

Message: Unsupported vFlash SD card detected.
Detailed Description: The SD card is not a valid vFlash SD card. The use of non-Dell media prevents the use of some extended capabilities and functions.
Recommended Response Action: Insert a supported vFlash SD card.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC012

Message: User is not authorized to perform this operation.
Detailed Description: The user credentials supplied do not have sufficient privileges to perform the operation.
Recommended Response Action: Retry the operation with user credentials authorized for the requested operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0120

Message: The selected partition size exceeds the available space.
Detailed Description: Requested partition size exceeds the available space.
Recommended Response Action: Enter a partition size smaller than the unused space on the vFlash SD card.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0121

Message: SD card is not initialized.
Detailed Description: SD card not readable. The card must be initialized.
Recommended Response Action: Initialize the SD card before it can be used.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0124

Message: Invalid label: Label must be exclusively alphanumeric characters.
Detailed Description: All characters in the label must be alphanumeric.
Recommended Response Action: Enter all alphanumeric characters.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0126

Message: The label value is invalid. Expected range: 1-6 alphanumeric characters.
Detailed Description: The label field is empty. A label is required to create an empty partition.
Recommended Response Action: Enter a label that contains one to six alphanumeric characters.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0127

Message: The specified size must be a non-fractional numeric value.
Detailed Description: Size must be a whole number.
Recommended Response Action: Enter a whole number for the size field.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0128

Message: An error has occurred in vFlash.
Detailed Description: A non-specific error has been detected while accessing the vFlash.
Recommended Response Action: Try the operation again in a few minutes. If the problem persists, reset iDRAC before trying the operation again.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0129

Message: An error has occurred while initializing the SD card.
Detailed Description: No status response was returned after completing the initialization request.
Recommended Response Action: Try reinitalizing the card again in a few minutes.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC013

Message: Invalid FQDD.
Detailed Description: The FQDD provided is not valid for the current method.
Recommended Response Action: Provide valid FQDD and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0130

Message: An error has occurred while creating a partition.
Detailed Description: A seperate message will provide more detail about this error which was detected while creating the vFlash partition.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0131

Message: An error has occurred while deleting a partition.
Detailed Description: A seperate message will provide more detail about this error which was detected while deleting the vFlash partition.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0132

Message: An error has occurred while formatting a partition.
Detailed Description: A seperate message will provide more detail about this error which was detected while formatting the vFlash partition.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0133

Message: An error has occurred while downloading a partition.
Detailed Description: A non-specific error has been detected when downloading the partition.
Recommended Response Action: Try downloading the partition again in a few minutes. If the problem persists, reset iDRAC before trying the operation again.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0134

Message: This operation is unavailable for non-vFlash SD cards.
Detailed Description: The SD card is not a valid vFlash SD card. The use of non-Dell media prevents the use of some extended capabilities and functions.
Recommended Response Action: Insert a valid vFlash SD card.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0135

Message: An error has occurred while detaching a partition.
Detailed Description: A seperate message will provide more detail about this error which was detected while detaching the vFlash partition.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0136

Message: An error has occurred while attaching a partition.
Detailed Description: A seperate message will provide more detail about this error which was detected while attaching the vFlash partition.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0137

Message: An error has occurred while changing the read-write state for the partition.
Detailed Description: A seperate message will provide more detail about this error which was detected while changing the read-write state of the vFlash partition.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0138

Message: A valid certificate is not loaded.
Detailed Description: The retrieved certificate came back as a null or empty document.
Recommended Response Action: Upload a valid certificate.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC014

Message: Invalid Attribute was entered.
Detailed Description: The attribute name provided is not valid for the current method.
Recommended Response Action: Provide valid attribute and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0140

Message: Firmware update has failed.
Detailed Description: The firmware update process returned an Update Failed status.
Recommended Response Action: Try the firmware update again in a few minutes. If the problem persists, try uploading the firmware through another interface such as Web GUI, RACADM, or DUPs.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0141

Message: Firmware update verification failed: The update status is unknown.
Detailed Description: Firmware update verification process failed; the firmware update status is unknown.
Recommended Response Action: Verify if the firmware has been updated by checking the new firmware version number. If it has not been updated try the firmware update again in a few minutes. If the problem persists, try uploading the firmware through another interface such as Web GUI, RACADM, or DUPs.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0142

Message: File is not valid for iDRAC firmware update.
Detailed Description: The firmware update process identified an invalid firmware image.
Recommended Response Action: Upload a valid iDRAC firmware image.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0146

Message: Firmware rollback has failed.
Detailed Description: Firmware rollback operation failed.
Recommended Response Action: Try the operation after a few minutes. If the problem persists, reset iDRAC and repeat the operation.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0147

Message: Rollback firmware is not available.
Detailed Description: Firmware rollback image is missing or is corrupt.
Recommended Response Action: Upload a new firmware image.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0148

Message: Unable to retrieve the batteries information. The system is powered off.
Detailed Description: While the system is powered off it is unable to retrieve information about the batteries.
Recommended Response Action: Turn the system on to view this information.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0149

Message: Unable to retrieve the fan information. The system is powered off.
Detailed Description: While the system is powered off it is unable to retrieve information about the fans.
Recommended Response Action: Turn the system on to view this information.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC015

Message

Not one of the Possible Values for AttributeName arg1 .

Arguments

arg1 = attribute name

Detailed Description

The attribute value is not valid for the attribute identified in the message.

Recommended Response Action

Provide valid attribute value for the attribute identified in the message and retry the operation.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC0150

Message: Unable to retrieve the intrusion sensor information. The system is powered off.
Detailed Description: While the system is powered off it is unable to retrieve information about system intrusion.
Recommended Response Action: Turn the system on to view this information.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0151

Message: Unable to retrieve the removable flash media information. The system is powered off.
Detailed Description: While the system is powered off it is unable to retrieve information about removable flash media.
Recommended Response Action: Turn the system on to view this information.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0152

Message: Unable to retrieve the power supply information. The system is powered off.
Detailed Description: While the system is powered off it is unable to retrieve information about power supplies.
Recommended Response Action: Turn the system on to view this information.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0153

Message: Non-redundant power mode: Check the system hardware manual for implications.
Detailed Description: Power redundancy is typically used to protect equipment from unexpected power disruption that could cause data loss or hardware damage.
Recommended Response Action: It is recommended to use power redundancy
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0154

Message: Non-redundant power mode: Secondary power supply has degraded.
Detailed Description: Displayed when a group of redundant power supplies has one or more individual power supplies with bad status.
Recommended Response Action: Replace the degraded power supply unit. Check the Power Supplies page for more information.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0155

Message: Unable to retrieve the temperature information. The system is powered off.
Detailed Description: While the system is powered off it is unable to retrieve information about system temperature.
Recommended Response Action: Turn the system on to view this information.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0156

Message: Unable to retrieve the voltage information. The system is powered off.
Detailed Description: While the system is powered off it is unable to retrieve information about system voltage.
Recommended Response Action: Turn the system on to view this information.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0158

Message: Uploading kerberos keytab has failed.
Detailed Description: The Kerberos keytab is needed by the iDRAC to authenticate itself to the Kerberos (Active Directory) server. It is created on the AD server, and issued for the iDRAC. Its like a password, and therefore should be kept secret.
Recommended Response Action: The Kerberos keytab file may be corrupt. Upload a valid Kerberos keytab file.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0159

Message: Certificate upload failed: No pending CSR or private key.
Detailed Description: Certificate upload failed because there is no pending Certificate Signing Request (CSR) or private key.
Recommended Response Action: Upload failed due to no pending Certificate Signing Request (CSR). Try creating a new CSR and then upload the certificate.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC016

Message: Invalid AttributeName.
Detailed Description: The attribute name provided is not valid for the current method.
Recommended Response Action: Provide valid attribute name and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0160

Message: Certificate upload failed: Cannot validate the certificate.
Detailed Description: Certificate upload failed because the certificate could not be validated.
Recommended Response Action: Certificate may be corrupt. Try creating a new Certificate Signing Request (CSR) and then upload the certificate.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0169

Message: Certificate upload failed: Certificate is not valid.
Detailed Description: Certificate upload failed because the certificate is not valid.
Recommended Response Action: Certificate may be corrupt. Try creating a new Certificate Signing Request (CSR) and then upload the certificate.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC017

Message: Job created to apply the attribute value.
Detailed Description: The requested job has been created.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0171

Message: Certificate upload failed: Certificate has expired.
Detailed Description: Certificate upload failed because the certificate has expired.
Recommended Response Action: Certificate has expired. Try creating a new Certificate Signing Request (CSR) and then upload the certificate.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC018

Message: Job completed with Errors.
Detailed Description: All the tasks in the Job were attempted, but some did not complete successfully.
Recommended Response Action: Examine source of the errors by inspecting the results from the job execution, and after resolving the issues, retry the operation. Job results can be retrieved from the Lifecycle Log or the WSMan API.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0180

Message: Certificate upload failed: Unable to get local issuer certificate from the Certification Authority (CA) for confirming the CA is legitimate.
Detailed Description: Certificate upload failed. Unable to get local issuer certificate. The local issuer certificate is the certificate for the Certificate Authority (CA) that has signed the certificate for the Active Directory (AD) server, unless it is self signed. The iDRAC needs to verify that the CA is legitimate.
Recommended Response Action: Certificate has expired. Try creating a new CSR and then upload the certificate.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC019

Message: Job did not complete successfully.
Detailed Description: The submitted job did not complete successfully.
Recommended Response Action: Examine source of the errors by inspecting the results from the job execution, and after resolving the issues, retry the operation. Job results can be retrieved from the Lifecycle Log or the WSMan API.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC020

Message: Completed
Detailed Description: The submitted job completed successfully.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0206

Message: Certificate upload failed: Not a certificate file.
Detailed Description: Certificate upload failed because this is not a certificate file.
Recommended Response Action: Upload a valid certificate.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0207

Message: Certificate upload failed.
Detailed Description: Certificate upload failed possibly due to poor network connection.
Recommended Response Action: Try the operation again in a few minutes. If the problem persists, issue a new Certificate Signing Request (CSR) and try again.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0208

Message: Upload failed: May be due to invalid key data.
Detailed Description: Upload failed possibly due to invalid key data.
Recommended Response Action: Upload a certificate with a valid key.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0209

Message: Certificate upload failed: iDRAC unable to upload at this time.
Detailed Description: Certificate upload failed because iDRAC unable to upload at this time.
Recommended Response Action: Try the operation again in a few minutes.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC021

Message: Unable to set static values for IPAddress Net mask or Gateway because DHCP is Enabled.
Detailed Description: Unable to set static values for IPAddress Net mask or Gateway because DHCP is Enabled.
Recommended Response Action: Disable DHCP to set static values for IPAddress Net mask or Gateway.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0211

Message: Firmware update has failed.
Detailed Description: Firmware update has failed. This may be due to a corrupt firmware image, poor network connection, or another issue.
Recommended Response Action: Download a new firmware image and try loading the firmware again.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0212

Message: Login failed. Verify that username and password is correct.
Detailed Description: This is a generic error message used on all the login pages.
Recommended Response Action: Enter valid credentials.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0213

Message: Missing Username.
Detailed Description: Login page is missing a username.
Recommended Response Action: Enter a valid username.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0214

Message: Missing Password.
Detailed Description: Login page is missing a password.
Recommended Response Action: Enter a valid password.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0215

Message: Login failed: User does not have Login to iDRAC privilege.
Detailed Description: Login failed because the user does not have Login to iDRAC privilege.
Recommended Response Action: Login to iDRAC privilege is needed.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0216

Message: Login failed.
Detailed Description: Login failed because of an unknown reason.
Recommended Response Action: Try the operation after a few minutes. If the problem persists, reset iDRAC and repeat the operation.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0217

Message: iDRAC is not responding.
Detailed Description: Client did not receive a response for the login request.
Recommended Response Action: Try pinging the iDRAC and then try again.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0218

Message: The maximum number of user sessions is reached.
Detailed Description: A maximum of 4 iDRAC Web GUI sessions can be open at any time.
Recommended Response Action: Close one or more sessions before opening another session.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0219

Message: Power command failed.
Detailed Description: Requested power state change has failed.
Recommended Response Action: Try the operation after a few minutes. If the problem persists, reset iDRAC and repeat the operation.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC022

Message: Unable to set values for User Password, IPMILan, IPMISerial or User Admin Privilege because the User Name is not configured.
Detailed Description: Unable to set values for User Password, IPMILan, IPMISerial or User Admin Privilege because the User Name is not configured.
Recommended Response Action: Set User Name before attempting to set values of other identified attributes.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0221

Message: The Destination E-mail Address is too long. The maximum length is 64 characters.
Detailed Description: The Destination E-mail Address can contain upto 64 characters.
Recommended Response Action: Enter an email address that contains upto 64 characters.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0222

Message: The Destination E-mail Address is invalid.
Detailed Description: The specified email address does not match an email address format. Ex: "janedoe@email.com."
Recommended Response Action: Enter a valid email address.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0223

Message: Enter an alphanumeric value or a valid symbol for the following (see the online help for more information):
Detailed Description: The Subject line in the email contains invalid characters.
Recommended Response Action: Invalid character. Enter a valid value as mentioned in the online help.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0224

Message: Invalid e-mail description.
Detailed Description: A partial string used to construct a complete error message.
Recommended Response Action: Enter a valid email description.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0225

Message: Sending the test mail failed.
Detailed Description: Sending the test mail failed. This will prevent alert messages from being sent to this email address.
Recommended Response Action: Confirm that: 1. A valid SMTP server address is configred in the iDRAC. 2. The remote email server is configured properly to send and receive emails.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0226

Message: Send Failed: Request processing failed.
Detailed Description: Sending the test mail failed. This will prevent alert messages from being sent to this email address.
Recommended Response Action: Confirm that: 1. A valid SMTP server address is configred in the iDRAC. 2. The remote email server is configured properly to send and receive emails.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0227

Message: SD card is not detected: Insert an SD Card of size greater than 256MB.
Detailed Description: The SD card is not present, or communication with the SD card is lost. This could result in reduced functionality and capabilities.
Recommended Response Action: This error may occur because: 1. Make sure the SD card is seated correctly. 2. The SD card is invalid. Insert a valid SD card of size greater than 256MB and try again.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0228

Message: SD Card is detected with an unrecognized format. Click Initialize to initialize the card.
Detailed Description: SD Card needs to be formatted to make it usable. The card must be initialized.
Recommended Response Action: Click Initialize to initialize the card and make it usable.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC023

Message: Unable to enable the User or set values for IPMILan, IPMISerial, or User Admin Privilege because the User Password is not configured.
Detailed Description: Unable to enable the User or set values for IPMILan, IPMISerial, or User Admin Privilege because the User Password is not configured.
Recommended Response Action: Set User Password before attempting to enable the other identified attributes.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0230

Message: This operation erases all data in the SD Card. Do you want to continue?
Detailed Description: This message is displayed when a confirmation is required to initialize the vFlash SD Card.
Recommended Response Action: Press OK to initialize the SD Card. This will erase all data. If undesired press Cancel.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0231

Message: This operation erases all data in the partition. Do you want to continue?
Detailed Description: This message is displayed when a confirmation is required to format the vFlash SD Card partition.
Recommended Response Action: Press OK to initialize this partition of the SD Card. This action will erase all the data in this partition. If undesired press Cancel.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0235

Message: vFlash image upload timed out.
Detailed Description: When uploading an image to the vFlash partition, the operation is unresponsive, and has timed out.
Recommended Response Action: Try uploading the vFlash image again.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0236

Message: Invalid image: Upload failed
Detailed Description: vFlash image upload failed because the image is not valid.
Recommended Response Action: Image may be corrupt. Try uploading a valid vFlash image.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0237

Message: An error occurred while uploading the vFlash image.
Detailed Description: A seperate message will provide more detail about this error which was detected while uploading the vFlash image.
Recommended Response Action: Try uploading the vFlash image again.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0238

Message: vFlash is currently in-use by another process. Try again later.
Detailed Description: vFlash is unable to service the request at this time. Try again later.
Recommended Response Action: Try the operation after a few minutes.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0239

Message: SD Card is write-protected.
Detailed Description: The contents of a write protected SD Card cannot be modified.
Recommended Response Action: Make sure the SD Card is not write-protected before attempting to change its contents.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC024

Message: Unable to VLAN is Disabled so cannot set VLAN Priority because VLAN is Disabled.
Detailed Description: Unable to VLAN is Disabled so cannot set VLAN Priority because VLAN is Disabled.
Recommended Response Action: Enable VLAN to set VLAN Priority.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0240

Message: vFlash is disabled.
Detailed Description: vFlash needs to be enabled before attempting this operation.
Recommended Response Action: Enable vFlash before trying the operation.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0241

Message

The specified size exceeds the maximum size of arg1 MB.

Arguments

arg1 = size

Detailed Description

SD Card does not have enough free space available.

Recommended Response Action

Delete existing data or insert a SD card of greater size and retry.

Category

Audit

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC0242

Message: The selected partition does not exist.
Detailed Description: The vFlash partition does not exist. This may be due to another user deleting that partition.
Recommended Response Action: Refresh the Web GUI page to see the available partitions.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0243

Message: Partition failed: A partitioning conflict has occurred with another session.
Detailed Description: There was a conflict with a concurrent session. Another user may have logged inusing a separate browser or RACADM.
Recommended Response Action: There was a conflict with a concurrent session. Refresh the page to see the currently available options.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0244

Message: The partition label must be unique.
Detailed Description: This message is displayed when a duplicate vFlash partition name is entered.
Recommended Response Action: Enter a unique label name for the partition.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0245

Message: The partition is in-use by another process.
Detailed Description: The vFlash partition is in-use by another process. Therefore, the current operation cannot proceed.
Recommended Response Action: Try the operation after a few minutes or with another partition. If the problem persists, reset iDRAC and repeat the operation.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0246

Message: Partition is read-only.
Detailed Description: The contents of a read-only partition cannot be modified.
Recommended Response Action: Make sure the partition is writable before attempting to change its contents.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0247

Message: The partition is currently attached.
Detailed Description: This message is displayed when trying to format or download to an attached vFlash partition.
Recommended Response Action: Detach this partition and try again.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0248

Message: This operation deletes the partition permanently. Do you want to continue?
Detailed Description: This message is displayed when trying to delete a vFlash partition.
Recommended Response Action: Press OK to delete this partition of the SD Card. This action will erase all the data in this partition. If undesired press Cancel.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0249

Message: One or more partitions are in-use by another process.
Detailed Description: The vFlash partition is in-use by another process. Therefore, the current operation cannot proceed.
Recommended Response Action: Try the operation after a few minutes. If the problem persists, reset iDRAC and repeat the operation.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC025

Message: Unable to set values for DNS1 or DNS2 attributes because DNS from DHCP is Enabled.
Detailed Description: Unable to set static values for DNS1 or DNS2 when DNS from DHCP is Enabled.
Recommended Response Action: Disable DNS from DHCP to set values for DNS1 or DNS2.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0250

Message: One or more partitions are read-only.
Detailed Description: The vFlash partitions are read-only. Therefore, the current operation cannot proceed.
Recommended Response Action: Make sure the partitions are writable before attempting to change their contents.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0251

Message: One or more partitions are currently attached.
Detailed Description: The vFlash partitions are attached. Therefore, the current operation cannot proceed.
Recommended Response Action: Detach the partitions and try again.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0252

Message: One or more partitions are currently detached.
Detailed Description: The vFlash partitions are detached Therefore, the current operation cannot proceed.
Recommended Response Action: Attach the partitions and try again.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0253

Message: The IP Address is invalid. Expected range: [1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Detailed Description: This error message is displayed to indicate that the IPv4 address does not conform to the required format.
Recommended Response Action: Enter a valid IP Address. Expected range: [1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0254

Message: The Gateway Address is invalid. Expected range: [0.0.0.0 or 1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Detailed Description: This error message is displayed to indicate that the IPv4 Gateway Address does not conform to the required format
Recommended Response Action: Enter a valid Gateway Address. Expected range: [0.0.0.0 or 1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0255

Message: The Subnet Mask is invalid. Expected ranges are: 255.XXX.0.0 [Class A], 255.255.XXX.0 [Class B], 255.255.255.XXX [Class C], and XXX.0.0.0 [others], where XXX must be valid (0,128,192,224,240,248,252,254).
Detailed Description: This error message is displayed to indicate that the IPv4 Subnet Mask does not conform to the required format.
Recommended Response Action: Enter a valid Subnet Mask. Expected ranges are: 255.XXX.0.0 [Class A], 255.255.XXX.0 [Class B], 255.255.255.XXX [Class C], and XXX.0.0.0 [others], where XXX must be valid (0,128,192,224,240,248,252,254).
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0256

Message: The Preferred DNS Server Address is invalid. Expected range: [0.0.0.0 or 1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Detailed Description: This error message is displayed to indicate that the Preferred DNS IPv4 address does not conform to the required format.
Recommended Response Action: Enter a valid Preferred DNS Server Address. Expected range: [0.0.0.0 or 1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0257

Message: The Alternate DNS Server Address is invalid. Expected range: [0.0.0.0 or 1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Detailed Description: This error message is displayed to indicate that the Alternate DNS IPv4 address does not conform to the required format.
Recommended Response Action: Enter a valid Alternate DNS Server Address. Expected range: [0.0.0.0 or 1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0259

Message: Invalid IPv6 address.
Detailed Description: This error message is displayed to indicate that the IPv6 address does not conform to the required format.
Recommended Response Action: Enter a valid IPv6 address.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC026

Message: Unable to set DNS Domain Name because "Domain Name From DHCP" is Enabled.
Detailed Description: Unable to set DNS Domain Name because "Domain Name From DHCP" is Enabled.
Recommended Response Action: Disable "Domain Name From DHCP" to set values for DNS Domain Name.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0260

Message: Invalid IPv6 prefix length. Expected range: 0-128.
Detailed Description: The specified IPv6 address prefix length is invalid.
Recommended Response Action: Enter a valid IPv6 prefix length. Expected range: 0-128.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0261

Message: Invalid IPv6 gateway address.
Detailed Description: This error message is displayed to indicate that the IPv6 gateway address does not conform to the required format.
Recommended Response Action: Enter a valid IPv6 gateway address.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0262

Message: The Preferred IPv6 DNS Server Address is invalid.
Detailed Description: This error message is displayed to indicate that the Preferred IPv6 DNS Server address does not conform to the required format.
Recommended Response Action: Enter a valid Preferred IPv6 DNS server address.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0263

Message: The Alternate IPv6 DNS Server Address is invalid.
Detailed Description: This error message is displayed to indicate that the Alternate IPv6 DNS Server address does not conform to the required format.
Recommended Response Action: Enter a valid Alternate IPv6 DNS server address.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0265

Message: Specify the VLAN ID and VLAN Priority.
Detailed Description: If VLAN is enabled, specify the VLAN ID and VLAN Priority.
Recommended Response Action: Enter a VLAN ID and VLAN Priority.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0266

Message: Invalid VLAN ID. Expected range: 1-4094.
Detailed Description: Specify a valid VLAN ID.
Recommended Response Action: Enter a valid VLan ID. Expected range: 1-4094.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0267

Message: Invalid VLAN Priority. Expected range: 0-7.
Detailed Description: Specify a valid VLAN Priority.
Recommended Response Action: Enter a valid VLAN Priority. Expected range: 0-7.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0268

Message: NIC is disabled.
Detailed Description: The NIC is disabled. This may adversely affect the current operation, and might not allow subsequent GUI interactions to this NIC.
Recommended Response Action: Enable the NIC before performing the operation.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0269

Message: The NIC MTU is invalid. Expected range: 576-1500 or 0x240-0x5DC.
Detailed Description: Specify a valid NIC MTU.
Recommended Response Action: Enter a valid NIC MTU. Expected range: 576-1500 or 0x240-0x5DC.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC027

Message: Unable to set values for Speed or Duplex because Auto Negotiation is Enabled.
Detailed Description: Unable to set static values for Speed or Duplex when the Auto Negotiation attribute is enabled.
Recommended Response Action: Disable Auto Negotiation in order to set values for Speed or Duplex.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0270

Message: IPv4 and IPv6 are disabled.
Detailed Description: This is a warning message that continuing this operation does not allow subsequent GUI interactions to this NIC.
Recommended Response Action: Enable IPv4 or IPv6 before continuing the operation.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0271

Message: Continuing will lock user account.
Detailed Description: Locking the user account prevents them from gaining access to iDRAC.
Recommended Response Action: Press OK to lock this user account. This action will prevent future access for this user. If undesired press Cancel.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0272

Message: Disabling NIC will prevent the user from accessing the iDRAC remotely through Web GUI, Remote Racadm, Ssh, and Telnet. Local Racadm and serial interface will continue to work.
Detailed Description: If the the Enable NIC checkbox is cleared, remote access to iDRAC is disabled.
Recommended Response Action: Disable NIC only if remote access is undesired.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0273

Message: iDRAC access will be limited to running the Racadm utility on the local server or using the serial interface.
Detailed Description: If the the Enable NIC checkbox is cleared, remote access to iDRAC is disabled.
Recommended Response Action: Enable remote access to access iDRAC remotely.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0274

Message: See the iDRAC user documentation for more information on using the Racadm utility or the serial interface.
Detailed Description: If the the Enable NIC checkbox is cleared, remote access to iDRAC is disabled.
Recommended Response Action: See iDRAC user documentation for more information on using racadm.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0275

Message: Click OK to disable the NIC. Click Cancel to keep the setting unchanged.
Detailed Description: If the the Enable NIC checkbox is cleared, remote access to iDRAC is disabled.
Recommended Response Action: Disable NIC only if remote access is undesired.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0276

Message: To save the changes and update this page, click Apply.
Detailed Description: If the the Enable NIC checkbox is cleared, remote access to iDRAC is disabled.
Recommended Response Action: Click Apply to save changes.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0277

Message: Disabling IPv4 prevents access to iDRAC using an IPv4 address.
Detailed Description: This warning message appears when IPv4 is disabled.
Recommended Response Action: Use IPv6 network to access iDRAC remotely.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0278

Message: Disabling IPv6 prevents access to iDRAC using an IPv6 address.
Detailed Description: This warning message appears when IPv6 is disabled.
Recommended Response Action: Use IPv4 network to access iDRAC remotely.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0279

Message: Invalid Encryption Key. Expected format: 0 to 40 characters, even number of characters and no blank spaces are allowed.
Detailed Description: An invalid IPMI encryption key was entered.
Recommended Response Action: Enter a valid encryption key of up to 40 characters. Odd number of characters and blank spaces are not allowed.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC028

Message: Unable to Enable "DNS Domain Name From DHCP" or "DNS From DHCP" because DHCP is Disabled.
Detailed Description: The attributes "DNS Domain Name From DHCP" and "DNS From DHCP" are dependent on the attribute DHCP being Enabled. Currently DHCP is configured as Disabled.
Recommended Response Action: Set DHCP attribute to Enable to be able to Enable DNS Domain Name From DHCP or DNS From DHCP.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0280

Message: The IP Range Address is invalid. Expected range: 0.0.0.0 - 255.255.255.255.
Detailed Description: This error message is displayed to indicate that the IPv4 address does not conform to the required format.
Recommended Response Action: Enter a valid IP Range Address. Expected range: 0.0.0.0 - 255.255.255.255.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0281

Message: The IP Subnet Mask is invalid. Expected range: 0.0.0.0 - 255.255.255.255.
Detailed Description: This error message is displayed to indicate that the IP Subnet Mask does not conform to the required format.
Recommended Response Action: Enter a valid IP Subnet Mask. Expected range: 0.0.0.0 - 255.255.255.255.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0282

Message: IP Blocking Fail Count is invalid. Expected range: 2-16.
Detailed Description: This is the number of login failures attempted from an IP address before further login attempts are rejected from that address. The default value is 10.
Recommended Response Action: Enter a valid IP Blocking Fail Count. Expected range: 2-16.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0283

Message: IP Blocking Fail Window is invalid. Expected range: 10-65535.
Detailed Description: This is the time span (in seconds) within which IP Blocking Fail Count failures must occur to trigger the IP Blocking Penalty Time. The default value is 3600 seconds (1 hour).
Recommended Response Action: Enter a valid IP Blocking Fail Window. Expected range: 10-65535.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0284

Message: IP Blocking Fail Penalty Time is invalid. Expected range: 10-65535.
Detailed Description: This is the time span (in seconds) within which login attempts from an IP address with excessive failures are rejected. The default value is 3600 seconds (1 hour).
Recommended Response Action: Enter a valid IP Blocking Fail Penalty Time. Expected range: 10-65535.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0285

Message: User name cannot be empty.
Detailed Description: The user name cannot be empty when creating a user account.
Recommended Response Action: Enter a user name.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0286

Message: New Password and Confirm New Password fields cannot be empty.
Detailed Description: When creating a user account, the New Password and Confirm New Password fields cannot be empty.
Recommended Response Action: Enter valid passwords for New Password and Confirm New Password.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0288

Message: Invalid entry: Entry must be exclusively alphanumeric characters and valid symbols.
Detailed Description: All characters entered must be alphanumeric or valid symbols.
Recommended Response Action: Enter all alphanumeric characters and valid symbols.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0289

Message: Values in New Password and Confirm New Password fields do not match.
Detailed Description: When creating a user account, the same value must be entered for New Password and Confirm New Password.
Recommended Response Action: Enter the same values for both New Password and Confirm New Password.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC029

Message: Required dependency not found in input.
Detailed Description: The input is missing required dependencies necessary for the operation.
Recommended Response Action: Refer to the Lifecycle Controller - Remote Services User Guide and retry the operation with required dependencies.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0290

Message: The user name cannot have spaces.
Detailed Description: The user name value does not accept spaces.
Recommended Response Action: Do not enter spaces in the user name. If desired, use underscores.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0291

Message: The user name cannot contain: /, \, @, ., or " (quotation mark).
Detailed Description: The user name value does not accept these characters.
Recommended Response Action: Do not enter /, \, @, ., or " (quotation mark) for user name.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0292

Message: A valid certificate is not loaded.
Detailed Description: This error is displayed when LDAP or Active Directory cannot find its certificate.
Recommended Response Action: Load a valid certificate.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0293

Message: When certificate validation is enabled, a valid root Certificate Authority (CA) certificate must be uploaded. The CA certificate is used to verify the directory server SSL certificate.
Detailed Description: This error is displayed when LDAP or Active Directory cannot find an associated Certificate Authority (CA) certificate.
Recommended Response Action: Upload a valid root Certificate Authority (CA) certificate.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0294

Message: The Character Accumulate Interval value is invalid. Expected range: 1-255.
Detailed Description: The amount of time iDRAC waits before sending a partial Serial Over LAN (SOL) data packet. This parameter is specified in milliseconds. It is recommended to use 10 milliseconds for optimal performance.
Recommended Response Action: Enter a valid Character Accumulate Interval value. Expected range: 1-255.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0295

Message: The Character Send Threshold value is invalid. Expected range: 1-255.
Detailed Description: This is the number of characters per Serial Over LAN (SOL) data packet. When the number of characters accepted by iDRAC is equal to or greater than the Character Send Threshold value, iDRAC starts transmitting SOL data packets that contain the numbers of characters equal to or less than the Character Send Threshold value. If a packet contains fewer characters than this value, it is defined to be a partial SOL data packet. It is recommended to use 255 characters for optimal performance.
Recommended Response Action: Enter a valid Character Send Threshold value. Expected range: 1-255.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0297

Message: Specify a Domain Controller Address must be configured.
Detailed Description: The Domain Controller Address be specified for Active Directory configuration.
Recommended Response Action: Enter a valid Domain Controller Address.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0298

Message: Root Domain Name must be configured.
Detailed Description: A Root Domain Name must be specified for Active Directory configuration.
Recommended Response Action: Root Domain Name must be configured.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC030

Message: The Required attribute that this Attribute is dependent on has an incorrect value.
Detailed Description: The attribute value provided for the Required attribute is invalid.
Recommended Response Action: Refer to the Lifecycle Controller - Remote Services User Guide and retry the operation with the appropriate value.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0301

Message: Remote File Share connection is unavailable. Check the settings and try again.
Detailed Description: User will be unable to connect to Remote File Share.
Recommended Response Action: Make sure proper connectivity exists between the client and the remote file share before using this feature.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0302

Message: iDRAC Express does not support this feature.
Detailed Description: This error message is displayed when iDRAC does not have a valid Enterprise license.
Recommended Response Action: Upgrade to iDRAC Enterprise for supporting this feature.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0303

Message: Virtual Console is disabled or you do not have the Access Virtual Console privilege.
Detailed Description: This error message is displayed when Virtual Console feature is unavailable.
Recommended Response Action: Enable Virtual Console and ask the administrator to grant Access Virtual Console privilege.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0304

Message: Firmware update is terminated.
Detailed Description: Firmware update is terminated.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC031

Message: Invalid value specified for the User name.
Detailed Description: The User name specified in the oepration is invalid.
Recommended Response Action: Retry command the operation with valid User name.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC032

Message: Invalid value specified for DNS RAC name.
Detailed Description: The DNS RAC name specified is not valid.
Recommended Response Action: Retry operation with valid DNS RAC name.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC033

Message: Unable to enable attribute because IPv4 is Disabled.
Detailed Description: The specified attribute cannot be enabled since it depends on IPv4 to be enabled.
Recommended Response Action: Enable IPv4 and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC034

Message: Unable to create a job because the job queue is full.
Detailed Description: The job queue is full.
Recommended Response Action: Wait for existing jobs to run to completion or delete some jobs from the job queue.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC035

Message: No pending configurations.
Detailed Description: There are no pending values for the any of the iDRAC attributes.
Recommended Response Action: Make sure there are pending values for the attributes that are targeted for configuration.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC036

Message: Attribute dependency failed.
Detailed Description: The value of the specified attribute is dependent on the value of another attribute. The current value dependency is invalid. The other attribute value must be changed before the specified attribute value can be set.
Recommended Response Action: Refer to the Lifecycle Controller-Remote Services documentation for the specified attribute dependency on another attribute value and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC037

Message: No pending configurations to delete.
Detailed Description: There are no pending configurations to delete.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0400

Message: iDRAC memory low.
Detailed Description: iDRAC is running low on memory.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0401

Message

idracmonitor: arg1

Arguments

arg1 = error string

Detailed Description

Critical error from iDRAC service recovery program.

Recommended Response Action

No response action is required

Category

Audit

Subcategory

RAC = RAC Event

Severity

Severity 1 (Critical)

LCD Message

No LCD message display defined.

Initial Default

LC Log;None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC049

Message: Resource allocation failure.
Detailed Description: The operation did not complete successfully because of lack of memory or file space in the iDRAC.
Recommended Response Action: Reset the iDRAC and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC050

Message: Invalid country code.
Detailed Description: The country code is not entered in the correct format or does not exist. Refer to ISO 3166 for the correct country code format.
Recommended Response Action: Enter country code in the correct format as defined in ISO 3166. For example, United States = US.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0500

Message: There are no batteries to be displayed.
Detailed Description: Batteries cannot be displayed. This error may occur if the host system is powered off or there is a bad or disconnected cable for batteries connected to the controller.
Recommended Response Action: 1. Check if the host system is powered off or shutdown. 2. Verify that the batteries are connected properly.
Category: Storage
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0501

Message: There are no physical disks to be displayed.
Detailed Description: Physical disks cannot be displayed. This error may occur if the host system is powered off or the physical disks are removed. This may result in communication loss while retrieving controller data.
Recommended Response Action: 1. Check if the host system is powered off or shutdown. 2. Check if the physical disks are inserted into the enclosure or attached to the backplane. 3. There are no out-of-band capable controllers detected.
Category: Storage
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0502

Message: There are no virtual disks to be displayed.
Detailed Description: Virtual disks cannot be displayed. This error may occur if the host system is powered off or there are no virtual disks created.
Recommended Response Action: 1. Check if the host system is powered off or shutdown. 2. Check if virtual disks are created.
Category: Storage
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0503

Message: There are no out-of-band capable controllers to be displayed.
Detailed Description: Out-of-band controllers cannot be displayed. This error may occur if the host system is powered off, or controllers are removed or disconnected.
Recommended Response Action: Check if the host system is powered off or shutdown.
Category: Storage
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0504

Message: There are no enclosures to be displayed.
Detailed Description: Enclosures cannot be displayed. This error may occur if the host system is powered off, there is no enclosure connected to the controller, or there is a bad or disconnected adapter cable for the enclosure.
Recommended Response Action: 1. Check if the host system is ON. 2. Check if the Storage Enclosure is ON. 3. Verify that the adapter cables are properly connected and there are no bent pins.
Category: Storage
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0505

Message: There are no devices to be displayed.
Detailed Description: Devices are not displayed. This error may occur because these components are removed or disconnected.
Recommended Response Action: 1. Check if the host system is ON. 2. Check if the Storage Enclosure is ON. 3. Verify that the adapter cables are properly connected and there are no bent pins.
Category: Storage
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0506

Message: You do not have privileges to perform this operation.
Detailed Description: This error occurs when the user tries to access a program or function that is beyond user granted privileges.
Recommended Response Action: Contact the system administrator to perform the operation or grant the required privileges.
Category: Storage
Subcategory: RAC = RAC Event
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0507

Message: Unable to find the requested resource.
Detailed Description: The requested information cannot be displayed, because the system did not find any matching resource. This occurs because the system is turned off, resource is not present, or the resource is removed or deleted. For example, resources such as physicals disks, vFlash SD card, SSL certificate or custom signing certificate.
Recommended Response Action: Do one of the following and retry the operation: 1) Turn on the system. 2) Make the resource available.
Category: Storage
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0508

Message: An unexpected error occurred.
Detailed Description: The server encountered an unexpected condition. This may be due to invalid JavaScript Object Notation.
Recommended Response Action: Wait for few minutes and refresh the page. If the problem persists, contact service provider.
Category: Storage
Subcategory: RAC = RAC Event
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0509

Message: The server is temporarily unavailable. Try again after sometime
Detailed Description: The server is currently unable to handle the request due to temporary overloading or server maintenance.
Recommended Response Action: Wait for few minutes and refresh the page. If the issue persists, contact service provider.
Category: Storage
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC051

Message

Unsupported parameter name arg1 .

Arguments

arg1 = parameter name

Detailed Description

The parameter name is not supported.

Recommended Response Action

Remove the unsupported parameter and retry the operation.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC0510

Message: There are no events to be displayed.
Detailed Description: This error occurs if Lifecycle log events have not occurred recently.
Recommended Response Action: No response action is required.
Category: Storage
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0511

Message: There are no physical disks to be displayed.
Detailed Description: Physical disks cannot be displayed. This error may occur if the host system is powered off, physical disks are removed, or incorrect filters are applied.
Recommended Response Action: 1. Check if the host system is powered off or shutdown. 2. Check if the physical disks are inserted into the enclosure or attached to the backplane. 3. Check if correct filters are applied. 4. Check that the Storage Enclosure is on. 5. verify that the adapter cables are properly connected and there are no bent pins.
Category: Storage
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0512

Message: There are no virtual disks to be displayed.
Detailed Description: Virtual disks cannot be displayed. This error may occur if the host system is powered off, no virtual disks were created, or incorrect filters are applied.
Recommended Response Action: 1. Check if the host system is ON. 2. Check if virtual disks are created. 3. Check if correct filters are applied. 4. Check if the Storage Enclosure is ON. 5. Verify that the adapter cables are properly connected and there are no bent pins.
Category: Storage
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0513

Message: There are no virtual disks to be displayed.
Detailed Description: There are no virtual disks to be displayed. There may be no virtual disks created, the controller(s) may not be in RAID mode, or there may be pending creation or deletion jobs that have not completed.
Recommended Response Action: Check the following: 1) Check if the server is turned off. If the server is turned off, turn it on and wait until POST completes. 2) If no virtual disks are created, to start the virtual disk creation process, click #{create_virtualdisk_link}. 3) If create virtual disk operation(s) are in a pending state, complete the creation process. To complete the virtual disk(s) creation, go to the Pendng Operations page and create a configuration job on the appropriate controller. 4) If delete virtual disk operation(s) are in pending state, then cancel the operation. To cancel delete virtual disk pending operation(s), go to the Pending Operations page and delete all pending operation(s) on the appropriate controller. 5) If the Controller(s) are in Non-RAID mode, switch the controller(s) to RAID mode. To switch controller(s) to RAID mode using the F2 System Setup utility, go to Device Settings > RAID Controller > Controller Management > Advanced Controller Management > Switch to RAID mode.
Category: Storage
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0514

Message: Unable to create virtual disk(s).
Detailed Description: Virtual disk(s) cannot be created because of one or more reasons identified in the Recommended Response Action.
Recommended Response Action: Check the following: 1) If no physical disk drives are available for virtual disk (VD) creation, install additional physical disk drives. 2) If the maximum number of VDs that can be created on the controller has been reached, a new VD cannot be created until an existing VD is deleted. 3) If the maximum number of VDs supported by drive group has been created, a new VD cannot be created until an existing VD is deleted from the selected drive group. 4) If the physical disk drive(s) are in non-RAID mode, convert them to RAID mode by pressing Ctrl+R while restarting the server, and then select the required controller. Press F2 and select the Convert to RAID capable option, and then complete the operation. 5) If a job is currently running or scheduled on the selected controller, the job must be completed or deleted before attempting a new operation. Status of the scheduled job can be viewed and managed on the Job Queue page on iDRAC. Click Job Queue link to view the status of the scheduled jobs.
Category: Storage
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC052

Message: Unable to create a configuration job because an existing configuration job is already in progress.
Detailed Description: Unable to create a configuration job because an existing configuration job is already in progress. Only one configuration job for a component can run or can be processed at any time.
Recommended Response Action: Retry the operation after the existing configuration job is complete, or cancel the existing configuration job and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC053

Message: OS to iDRAC pass-through is disabled.
Detailed Description: One or more attributes being set are dependent on OS to iDRAC pass-through being enabled.
Recommended Response Action: Enable OS to iDRAC pass-through and retry the previous command.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC054

Message: User account attributes cannot be reset to default values due to an internal error.
Detailed Description: The user account attributes cannot be reset to default values due to an internal error.
Recommended Response Action: Make sure the configuration XML file contains valid values for user account attributes and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC055

Message: User name cannot be cleared because the user account is enabled in the input configuration XML file.
Detailed Description: The user name for the user account cannot be cleared because the user account is enabled in the configuration XML file.
Recommended Response Action: Retry the operation after disabling the user account in the configuration XML file.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC056

Message

Unable to set the Authentication Protocol attribute to None because the Privacy Protocol attribute is enabled for user ID: arg1

Arguments

arg1 = user ID

Detailed Description

The Authentication Protocol attribute for the user account identified in the message cannot be disabled because the Privacy Protocol attribute is enabled. The Privacy Protocol for the user account is not set to None.

Recommended Response Action

Disable the Privacy Protocol attribute for the identified user ID account by setting the value to None, and retry the operation to set Authentication Protocol attribute to None.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC0560

Message: RAC Software Initialization Error
Detailed Description: RAC Software Initialization error. Monitoring data will not be available for PERC and Network Cards
Recommended Response Action: Contact Dell Tech Support
Category: System Health
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
Trap/EventID: 2531
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0561

Message: iDRAC to CMC communication link is not functioning for agent free monitoring of chassis PCIe slots.
Detailed Description: iDRAC lost connection with CMC proxy component that enables agent free monitoring of PCIe slots. Agent free monitoring will not be supported for Chassis PCIe slots while this connection is not functioning.
Recommended Response Action: Do the following: 1) Check the Lifecycle Log for the subsequent RAC0562 communications restored message that will indicate the link was re-established automatically. 2) If there is no subsequent RAC0562 message in the Lifecycle Log, restart the iDRAC. The iDRAC can be restarted by using the RACADM command line utility and entering "racadm racreset". 3) After the iDRAC has restarted, if the communications link is still not functioning, restart the CMC and check the Lifecycle Log for this link error after the CMC has restarted. 4) If the issue persists, contact your service provider.
Category: System Health
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
Trap/EventID: 2531
LCD Message: No LCD message display defined.
Initial Default: LC Log;None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0562

Message: iDRAC-CMC communication restored for agent free monitoring of chassis PCIe slots.
Detailed Description: iDRAC automatically restored connection with CMC proxy component. Agent free Monitoring will now be supported for Chassis PCIe slots.
Recommended Response Action: No response action is required.
Category: System Health
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
Trap/EventID: 2531
LCD Message: No LCD message display defined.
Initial Default: LC Log;None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC057

Message

Unable to set Privacy Protocol to an enabled state because the Authentication Protocol attribute is set to None for the user ID: arg1

Arguments

arg1 = user ID

Detailed Description

The Privacy Protocol for the user cannot be enabled because the Authentication protocol is disabled.

Recommended Response Action

Enable the Authentication Protocol attribute for the identified user ID account, and retry the operation to set the Privacy Protocol to an enabled state.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC058

Message

AttributeValue is not unique for AttributeName arg1 .

Arguments

arg1 = attribute name

Detailed Description

The value provided for the specified attribute is not unique. For example, the user name for a user account must be unique.

Recommended Response Action

Provide a unique value for the specified attribute. For more information about the component being managed, see the DCIM Profile documentation.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC059

Message: Unable to configure iDRAC time because Network Time Protocol (NTP) is enabled.
Detailed Description: When the Network Time Protocol (NTP) feature is enabled, the iDRAC will get time from the configured NTP server. Directly configuration of the iDRAC time is disabled when NTP is enabled.
Recommended Response Action: Disable Network Time Protocol (NTP) and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC060

Message

Unable to set the attribute because OpenManage Server Administrator (OMSA) is installed on the server arg1

Arguments

arg1 = attribute name

Detailed Description

The attribute identified in the message could not be set, because certain features cannot be enabled when OMSA is installed on the server.

Recommended Response Action

Uninstall OMSA, and then retry the operation.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC0600

Message: Unable to retrieve the temperature information.
Detailed Description: Temperature information cannot be displayed. This error may occur if the server is powered off.
Recommended Response Action: Power on the server. If the server is already powered on, wait for a few minutes and refresh the page. If the problem persists, contact service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0601

Message: Unable to retrieve alert recurrence information.
Detailed Description: The server encountered an unexpected condition. This may be due to invalid JavaScript Object Notation.
Recommended Response Action: Wait for few minutes and refresh the page. If the problem persists, contact service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0602

Message: Invalid value for alert recurrence.
Detailed Description: The value for alert recurrence must be within the range 0-365.
Recommended Response Action: Enter a value between 0-365.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0603

Message: Updating Job Queue. Status of the update jobs can be viewed and managed within the Job Queue page.
Detailed Description: The Job Queue is updated with the selected update jobs. The status of the update jobs can be viewed and managed within the Job Queue page.
Recommended Response Action: Click Job Queue button to view the status of the update jobs.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0604

Message: System inventory may not be up-to-date because Collect System Inventory On Restart (CSIOR) is disabled.
Detailed Description: The system inventory may not be up-to-date because the Collect System Inventory On Restart (CSIOR) feature is disabled. The CSIOR feature retrieves detailed system inventory information during system startup and stores this information on iDRAC.
Recommended Response Action: Enable CSIOR, restart the system and retry the operation. To enable CSIOR, press F2 (System Setup) during system startup, navigate to iDRAC Settings >Lifecycle Controller, and select the Enabled option for Collect System Inventory on Restart.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0605

Message: There are no jobs to be displayed.
Detailed Description: There are no jobs to be displayed.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0606

Message: The network connection test operation was successful.
Detailed Description: The selected network connection test operation was successsful.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0607

Message: Unable to perform OS to iDRAC Pass-Through with the current system configuration.
Detailed Description: The integrated NICs in the system do not support OS to iDRAC Pass-Through.
Recommended Response Action: Make sure the integrated NICs are enabled from BIOS setup and support OS to iDRAC Pass-Through, then retry the operation. To access BIOS setup, press F2 during system startup. For more information about OS to iDRAC Pass-Through, see iDRAC7 Users Guide.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0608

Message: The iDRAC will restart when the iDRAC firmware update is complete. All current user sessions will be closed.
Detailed Description: The message appears in Job Queue page when the iDRAC firmware update job status is downloading. Communication to the iDRAC will be lost when the iDRAC restarts to complete the firmware update.
Recommended Response Action: Reconnect iDRAC communications session after iDRAC is restarted. The iDRAC will be ready for login once the restart is complete.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0609

Message

The job arg1 has been successfully added to the job queue.

Arguments

arg1 = import or export job ID

Detailed Description

The import or export system configuration operation with the job ID indicated in the message was successfully added to the Job Queue.

Recommended Response Action

No response action is required. The status of jobs can be viewed on the Job Queue page.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC061

Message: Unable to set the IPMI Watchdog because the OS Watchdog is already enabled..
Detailed Description: The IPMI Watchdog can not be enabled at the same time as the OS Watchdog.
Recommended Response Action: Disable the OS Watchdog before enabling IPMI Watchdog.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0610

Message: The passphrase and confirm passphrase values entered do not match.
Detailed Description: Different values were entered for passpharse and confirm passpharse field.
Recommended Response Action: Values entered in passphrase and confirm passphrase fields must be the same.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0611

Message: IP Address cannot be blank.
Detailed Description: The IP address cannot be blank for import or export of system configuration profile operation.
Recommended Response Action: Enter a valid IP Address for network location.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0612

Message: Cancelling the firmware update operation will delete all the uploaded firmware files. Do you want to continue?
Detailed Description: Cancelling the firmware update operation will cancel all firmware updates selected and delete all uploaded firmware files.
Recommended Response Action: Select Yes to cancel the firmware update operation and delete all uploaded firmware files. Select No to dismiss the message and continue the firmware update operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0613

Message: The uploaded file is invalid.
Detailed Description: An internal error occurred because of an invalid file.
Recommended Response Action: Make sure to upload the required file in the correct format and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0614

Message: Incorrect password for PKCS#12 file.
Detailed Description: The specified password was incorrect for the PKCS#12 file.
Recommended Response Action: Make sure to use the correct password for the PKCS#12 file. If the PKCS#12 file is encrypted with a password, add it in required password box. Leave the password box empty if the file was not encrypted with a password.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0615

Message: Invalid PKCS#12 file.
Detailed Description: The contents of the PKCS12 file was not valid because one of the following: 1) Not a valid PKCS#12 file, 2) Not a valid pfx file or 3) Did not contain a valid key.
Recommended Response Action: Make sure to upload the file in PKCS#12 format. OpenSSL can be used to validate a PKCS#12 file.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0616

Message: Error while extracting custom signing certificate and private key from the PKCS#12 file.
Detailed Description: iDRAC was unable to continue with the operation after the PKCS#12 file was uploaded, because it is not able to extract the custom signing certificate and private key.
Recommended Response Action: Make sure to upload the PKCS#12 file that contains a valid custom signing certificate and private key.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0617

Message: An error was encountered while generating new SSL Certificate.
Detailed Description: An error occurred while generating new iDRAC SSL Certificate or signing it with new custom signing certificate.
Recommended Response Action: Make sure to upload an PKCS#12 file that contains a valid custom signing certificate and private key, then retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0618

Message: Incorrect data entered.
Detailed Description: The data entered caused an error while processing the request.
Recommended Response Action: Make sure to enter the correct data and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0619

Message: The iDRAC firmware rollback will cause an iDRAC restart and all current user sessions will be closed.
Detailed Description: The message appears in Firmware Rollback page when the iDRAC firmware rollback action completed successfully.
Recommended Response Action: Reconnect iDRAC communications sessions after iDRAC is restarted. The iDRAC will be ready for login once the restart is complete.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC062

Message: Unable to set the WatchdogResetTime because the IPMI Watchdog state is disabled.
Detailed Description: The WatchdogResetTime can not be set if the IPMI Watchdog state is disabled.
Recommended Response Action: Enable the IPMI Watchdog state and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0620

Message: Lifecycle Controller is unable to delete the selected jobs.
Detailed Description: Lifecycle Controller is currently busy performing tasks. The selected jobs cannot be deleted until the following: 1) The Lifecycle Controller tasks are completed. 2) The system completes all the Power-on-Self-test (POST) operations.
Recommended Response Action: Wait until Lifecycle Controller completes the current tasks and the system completes Power-on Self-test (POST).
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0621

Message: Successfully completed the iDRAC firmware update. All current user sessions will be closed.
Detailed Description: The message appears in Job Queue page when the iDRAC firmware update job status is completed. Communication to the iDRAC will be lost .
Recommended Response Action: The iDRAC will be ready for login once the restart is complete.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0622

Message: An invalid certificate file is uploaded.
Detailed Description: The certificate file is invalid for one of the following reasons: 1) CA Certificate is corrupted, expired, or does not have signing privileges. 2) CA private key does not matchi with CA Certificate being uploaded.
Recommended Response Action: Make sure the CA certificate and private key are correct and retry the operation. The certificate can be validated using the OpenSSL tools.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC063

Message

The string length of the provided value for arg1 is inappropriate.

Arguments

arg1 = attribute name

Detailed Description

The string length of the entered value for the attribute identified in the message may be less than the minimum length or greater than the maximum length allowed.

Recommended Response Action

Make sure that the string length is correct and retry the operation.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC064

Message: iDRAC was successfully reset.
Detailed Description: iDRAC was successfully reset.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC065

Message: iDRAC reset operation was not successful.
Detailed Description: The iDRAC reset operation was not successful. This may be due to IPMI communications issues.
Recommended Response Action: Do the following: 1) Retry the operation. 2) If the issue persists, remove AC input power from the server and re-apply AC power to the server and retry the operation. 3) If the issue constinues to persist, contact your service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0654

Message: No operations can be performed on the iDRAC Service Module.
Detailed Description: Unable to perform operations on the iDRAC Service Module (iSM) because the iSM is not installed on the server operating system. All fields in the iDRAC GUI iSM page are disabled.
Recommended Response Action: Make sure that the iDRAC Service Module is installed on the server operating system, and then retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0655

Message: The Replicate Lifecycle Controller Log in OS Log and Auto System Recovery Action features are disabled in the iDRAC Service Module because the OpenManage Server Administrator is installed on the server operating system.
Detailed Description: The Replicate Lifecycle Controller Log in OS Log and Auto System Recovery Action features are disabled in the iDRAC Service Module because the OpenManage Server Administrator is installed on the server operating system.
Recommended Response Action: None
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0656

Message: Are you sure you want to disable the iDRAC Service Module on the server operating system?
Detailed Description: The iDRAC Service Module (iSM) service cannot be started by just enabling in iDRAC web interface because the service has to also be manually restarted on the server operating system.
Recommended Response Action: To re-enable the iDRAC Service Module (iSM), do the following: 1) Enable the iSM in the iDRAC web interface, 2) Start the iSM service on the server operating system.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0657

Message: The file name field must not be blank.
Detailed Description: The file name cannot be blank when performing the Backup Server Profile operation.
Recommended Response Action: Enter an appropriate file name, and then retry the operation.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC066

Message: iDRAC is successfully reset to factory-default properties.
Detailed Description: iDRAC was successfully reset to factory-default properties.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC067

Message: iDRAC reset to factory defaults operation was not successful.
Detailed Description: iDRAC reset to factory defaults operation was not successful. This may be due to IPMI communications issues.
Recommended Response Action: Do the following: 1) Retry the operation. 2) If the issue persists, remove AC input power from the server and re-apply AC power to the server and retry the operation. 3) If the issue constinues to persist, contact your service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC068

Message: SHA256Password and Plain Password cannot be imported together.
Detailed Description: Both SHA256Password and Plain Password cannot be attempted to set together on Configuration import per user.
Recommended Response Action: One of either SHA256Password or Plain password can be attempted to be imported for an user.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log;None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC069

Message: String Less than Min Supported Length
Detailed Description: String Less than Min Supported Length
Recommended Response Action: None
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: LC Log;None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC070

Message: The SSL Web-Server certificate was successfully restored to factory defaults.
Detailed Description: The SSL Web-Server certificate was successfully restored to factory defaults.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0700

Message

Email page successful to arg1 .

Arguments

arg1 = email address

Detailed Description

An email page was successfully sent.

Recommended Response Action

No response action is required.

Category

Audit

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

LC Log

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC0701

Message: Requested system powerup.
Detailed Description: Requested system powerup.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0702

Message: Requested system powercycle.
Detailed Description: Requested system powercycle.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0703

Message: Requested system hardreset.
Detailed Description: Requested system hardreset.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0704

Message: Requested system powerdown.
Detailed Description: Requested system powerdown.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0705

Message: Requested system graceful shutdown.
Detailed Description: Requested system graceful shutdown.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0706

Message: Requested system NMI.
Detailed Description: Requested system NMI.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0707

Message: Primary Firmware image is invalid. Currently booted from backup image. To restore primary image, update the firmware.
Detailed Description: Primary Firmware image is invalid. Currently booted from backup image. To restore primary image, update the firmware.
Recommended Response Action: Acquire an iDRAC firmware image of the version desired. Using the latest version available is recommended. Update the iDRAC firmware.
Category: Updates
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0708

Message: Previous reboot was due to a firmware watchdog timeout.
Detailed Description: Previous reboot was due to a firmware watchdog timeout.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0709

Message: Unknown server inserted into chassis.
Detailed Description: Unknown server inserted into chassis.
Recommended Response Action: Acquire the latest Chassis Management Controller (CMC) firmware that supports the server indicated and update the CMC to at least that version.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC071

Message: Unable to perform the iDRAC reset operation because the firmware upgrade operation is in progress.
Detailed Description: The iDRAC reset operation cannot be completed because a firmware upgrade operation is in progress.
Recommended Response Action: Wait for the current update process to complete and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0710

Message: Server link tuning error.
Detailed Description: Server link tuning error.
Recommended Response Action: Ensure that the IO Module (IOM) and Mezzanine (Mezz) cards are appropriately matched. Check the M1000e Hardware Manual for correct component compatibility.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0711

Message: Unknown power on response from the CMC.
Detailed Description: Unknown power on response from the CMC.
Recommended Response Action: Try reseting the CMC. Also try reseating the server.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0712

Message: Server failed to power up due to zero power allocated.
Detailed Description: Server failed to power up due to zero power allocated.
Recommended Response Action: Utilize the Chassis Management Controller web interface to check available power and server power requirements. If sufficient power is available, allocate power necessary and retry the operation.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0713

Message: Server failed to power up due to fabric mismatch.
Detailed Description: Server failed to power up due to fabric mismatched.
Recommended Response Action: Ensure that the hardware comtibility between the IO Module (IOM) and the Mezzanine (Mezz) card is correct. Check the M1000e Hardware Manual for correct component compatibility.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0714

Message: Server failed to power up due to noncontinuous power action.
Detailed Description: Server failed to power up due to noncontinuous power action.
Recommended Response Action: Utilize the Chassis Management Controller web interface to check available power and server power requirements. If sufficient power is available, allocate power necessary and retry the operation.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0715

Message: Image file does not exist in the given remote share path.
Detailed Description: Image file does not exist in the given remote share path.
Recommended Response Action: Ensure that the image file is available on the share path provided. Retry the operation.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0716

Message: Unable to unmount remote share.
Detailed Description: Unable to unmount remote share.
Recommended Response Action: Retry the operation.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0717

Message: Remote share unmounted successfully.
Detailed Description: Remote share unmounted successfully.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0718

Message: Remote File Share service is busy with the previous connection.
Detailed Description: Remote File Share service is busy with the previous connection.
Recommended Response Action: Stop the Remote File Share session and retyr the operation.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0719

Message: Not able to connect to remote file share. Virtual media devices are already in use.
Detailed Description: Not able to connect to remote file share. Virtual media devices are already in use.
Recommended Response Action: Stop existing Virtual Media sessions and retry the operation.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC072

Message: Unable to perform the iDRAC reset to factory defaults operation because the firmware upgrade is in progress.
Detailed Description: The iDRAC reset to factory defaults operation cannot be completed because a firmware upgrade operation is in progress.
Recommended Response Action: Wait for the current update process to complete and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0720

Message

Unable to mount remote share arg1 .

Arguments

arg1 = sharename

Detailed Description

Unable to mount remote share.

Recommended Response Action

Retry the operation.

Category

Audit

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

LC Log

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC0721

Message

Remote share mounted successfully arg1 .

Arguments

arg1 = sharename

Detailed Description

Remote share mounted successfully.

Recommended Response Action

No response action is required.

Category

Audit

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

LC Log

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC0722

Message

Failed to program the Chassis assigned MAC address for the NIC.Integrated. arg1 .

Arguments

arg1 = NDC slot number

Detailed Description

Failed to program the Chassis assigned MAC address for the NIC.Integrated in the specified slot number.

Recommended Response Action

Reseat the server and retry.

Category

Audit

Subcategory

RAC = RAC Event

Severity

Severity 1 (Critical)

LCD Message

No LCD message display defined.

Initial Default

LC Log

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC0723

Message

The firmware version arg1 of the Chassis Management Controller is earlier than the required version arg2 .

Arguments

arg1 = version number
arg2 = version number

Detailed Description

The Chassis Management Controller firmware version identified in the message is earlier than the version required to support the server.

Recommended Response Action

Update the Chassis Management Controller firmware to the required version identified in the message.

Category

Audit

Subcategory

RAC = RAC Event

Severity

Severity 1 (Critical)

LCD Message

No LCD message display defined.

Initial Default

SNMP Alert;OS Log;LC Log;Remote System Log

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC0724

Message: Quick Sync Firmware is successfully updated.
Detailed Description: Quick Sync Firmware is successfully updated.
Recommended Response Action: No response action is required.
Category: Updates
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0725

Message: Unable to update the Quick Sync Firmware.
Detailed Description: Unable to update the Quick Sync Firmware.
Recommended Response Action: No response action is required.
Category: Updates
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0726

Message: Auto-throttling is disabled for the server.
Detailed Description: Auto-throttling is disabled for the server based on a request from the Chassis Management Controller (CMC) because the CMC is restarting..
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0727

Message: Auto-throttling is enabled for the server.
Detailed Description: Auto-throttling is enabled for the server based on a request from the Chassis Management Controller (CMC) because the CMC has restarted.
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0728

Message: The Quick Sync communication is no longer functioning.
Detailed Description: The Quick Sync communication or the connection to the iDRAC is no longer functioning.
Recommended Response Action: Do the following: 1) Remove and reseat the bezel. 2) Turn the bezel on by pressing the activation button. 3) Try the Quick Sync feature again. If the issue persists, contact your technical support provider.
Category: System Health
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC073

Message: Unable to perform the iDRAC reset operation because a vFlash partition creation operation is in progress.
Detailed Description: The iDRAC reset operation cannot be completed because a vFlash partition creation operation is in progress.
Recommended Response Action: Wait for the vFlash partition creation process to complete and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC074

Message: Unable to perform the iDRAC reset to factory defaults operation because a vFlash partition creation operation is in progress.
Detailed Description: The iDRAC reset to factory defaults operation cannot be completed because a vflash partition creation operation is in progress.
Recommended Response Action: Wait for the vFlash partition creation process to complete and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0801

Message: iDRAC is being reset.
Detailed Description: iDRAC closes all the existing sessions and returns to the default static IP address.
Recommended Response Action: No response action is required
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0901

Message: Invalid syntax. The -t option value must set to 1.
Detailed Description: The syntax of the specified command is invalid. In this case, the usage of the -t option is invalid.
Recommended Response Action: See the help text/documentation for the valid syntax of the subcommand.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0902

Message: The -f option requires -d to also be specifed.
Detailed Description: The syntax of the specified command is invalid. In this case, the usage of the -f option is invalid.
Recommended Response Action: See the help text/documentation for the valid syntax of the subcommand.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0903

Message: The -d option cannot be used with any other options.
Detailed Description: The syntax of the specified command is invalid. In this case, the usage of the -d option is invalid.
Recommended Response Action: See the help text/documentation for valid syntax of the subcommand.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0904

Message: The remote file location is not accessible or reachable.
Detailed Description: The iDRAC cannot access the remote file location. The credentials or path to the remote file location is incorrect or iDRAC cannot connect to the network address.
Recommended Response Action: Confirm that the path and credentials to remote file are correct, and check that the iDRAC can connect to the network address.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0905

Message: Failed to get the USC version details.
Detailed Description: Unable to obtain the USC version details.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0906

Message: Operation failed.
Detailed Description: Unable to perform the requested operation.
Recommended Response Action: Try again later. If the problem persists, contact technical support. Refer to your product documentation to choose the contact method.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0907

Message: System ID LED blink on.
Detailed Description: The System ID LED was successfully set to on.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0908

Message: System ID LED blink off.
Detailed Description: The System ID LED was successfully set to off.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0909

Message: Invalid subcommand syntax: Specify the object name.
Detailed Description: The specified command is missing object name syntax.
Recommended Response Action: Specify the correct subcommand object name syntax. See the help text or documentation for valid syntax.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0910

Message: Invalid subcommand syntax: Specify group and object name.
Detailed Description: The specified command is missing group and object name syntax.
Recommended Response Action: Specify the correct subcommand group and object name syntax. See the help text or documentation for the valid syntax.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0911

Message: Data about version details is unavailable.
Detailed Description: Unable to retrieve version details.
Recommended Response Action: Try again later. If the problem persists, contact technical support. Refer to your product documentation to choose the contact method that is convenient for you.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC0912

Message: Unable to connect to RAC at specified IP address.
Detailed Description: The management system could not connect to the iDRAC.
Recommended Response Action: Verfiy whether the IP address of the remote iDRAC is correct. Verify whether connectivity exists between the management system and the iDRAC.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1000

Message: Unable to set the object value for iDRAC IPv6 address or gateway.
Detailed Description: Unable to set the object value for iDRAC IPv6 Address1 and IPv6 Gateway, because the object IPv6 Autoconfig is enabled.
Recommended Response Action: Disable the object IPv6 AutoConfig using "racadm set iDRAC.IPv6.AutoConfig <0 | Disabled >", and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1001

Message: Unable to set the object value for iDRAC IPv6 DNS1 or DNS2.
Detailed Description: Unable to set the object value for iDRAC IPv6 DNS1 or DNS2, because the object DNSFromDHCP6 is enabled.
Recommended Response Action: Disable the object DNSFromDHCP6 using "racadm set iDRAC.IPv6.DNSFromDHCP6 <0 | Disabled>", and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1002

Message: Active Directory Single Sign On (SSO) cannot be enabled.
Detailed Description: The Active Directory SSO cannot be enabled, because the object SmartCardLogonEnable is enabled.
Recommended Response Action: Disable the object SmartCardLogonEnable using "racadm set iDRAC.SmartCard.LogonEnable <0 | Disabled>", and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1003

Message: The smart card certificate revocation list (CRL) cannot be enabled.
Detailed Description: The smart card certificate revocation list (CRL) cannot be enabled, because the object SmartCardLogonEnable is disabled.
Recommended Response Action: Enable the object SmartCardLogonEnable using "racadm set iDRAC.SmartCard.SmartCardLogonEnable <1 | Enabled>", and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1004

Message: The smart card login cannot be enabled.
Detailed Description: The smart card login cannot be enabled, because the Active Directory Single Sign On is enabled.
Recommended Response Action: Disable Active Directory Single Sign On (SSO) using "racadm set iDRAC.ActiveDirectory.SSOEnable <0 | Disabled>", and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1005

Message: Successfully exported hardware inventory.
Detailed Description: The hardware inventory was successfully exported.
Recommended Response Action: No response action is required
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1006

Message

Unable to process the arg1 , and the update was not applied.

Arguments

arg1 = file name

Detailed Description

The update was not applied because of one of the following reasons: 1) The Update Package is invalid. 2) Lifecycle Controller is corrupted. 3) Another update is in progress.

Recommended Response Action

Do one of the following and retry the operation: 1) Dowload the correct Update Package from your service provider. 2) Use the Lifecycle Controller repair package to repair Lifecycle Controller. For more information, see Lifecycle Controller Users Guide. 3) Wait until the current update operation is complete.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1007

Message

The job arg1 cannot be deleted.

Arguments

arg1 = job ID

Detailed Description

The job specified in the meesage cannot be deleted when it is Running, Scheduled, or tranitioniong from Downloading to Scheduled.

Recommended Response Action

Wait until the specified job is completed, or reboot the system to move the job to Completed state. To view the job status, use "racadm jobqueue view -i <Job_ID>".

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1008

Message: The Active Directory object DCLookupByUserDomain cannot be disabled.
Detailed Description: The Active Directory object DCLookupByUserDomain cannot be disabled, because the Active Directory object DCLookupDomainName is not configured.
Recommended Response Action: Configure the Active Directory object DCLookupDomainName using "racadm set iDRAC.ActiveDirectory.DCLookupDomainName <Name>", and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1009

Message: The Active Directory objects DCLookupEnable or GCLookupEnable cannot be enabled.
Detailed Description: The Active Directory objects DCLookupEnable or GCLookupEnable cannot be enabled, because IPv4.DNS1, IPv4.DNS2, IPv6.DNS1, or IPv6.DNS2 is not configured.
Recommended Response Action: Configure IPv4.DNS1, IPv4.DNS2, IPv6.DNS1, or IPv6.DNS2 using racadm set command, and retry the operation. For example, "racadm set iDRAC.IPv4.DNS1 <address>".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1010

Message: Unable to set the power cap value.
Detailed Description: The power cap cannot be set if the object Power.Cap is disabled.
Recommended Response Action: Enable Power Cap setting using "racadm set System.Power.Cap.Enable < 1 | Enabled >", and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1011

Message: The OS to iDRAC pass-through cannot be enabled.
Detailed Description: The OS to iDRAC pass-through cannot be enabled, because the NIC is in Dedicated mode.
Recommended Response Action: Change the iDRAC NIC mode to shared mode using "racadm set idrac.nic.selection <value>", and retry the opeation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1012

Message: Unable to change the auto-negotiation state for the current NIC selection mode.
Detailed Description: Unable to change the auto-negotiation state for the current NIC selection mode, because the iDRAC NIC is in dedicated mode.
Recommended Response Action: Change the iDRAC NIC mode to shared mode using "racadm set idrac.nic.selection <value>", and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1013

Message: The SNMPv3 authentication protocol state cannot be set to None if the SNMPv3 privacy protocol state is set to None.
Detailed Description: For any iDRAC user, SNMPv3 authentication protocol can be changed to "None" only if the SNMPv3 privacy protocol state is set to "None".
Recommended Response Action: Change the SNMPv3 privacy protocol state to None using "racadm set iDRAC.Users.<index>.SNMPv3PrivacyType none", and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1014

Message: The SNMPv3 privacy protocol cannot be configured to AES or DES mode if SNMPv3 authentication protocol state is set to "None".
Detailed Description: The SNMPv3 privacy protocol cannot be configured to AES or DES mode if SNMPv3 authentication protocol state is set to "None".
Recommended Response Action: To configure the SNMPv3 Privacy Protocol for a specified iDRAC user, change the SNMPv3 Authentication Protocol to either MD5 or SHA state using "racadm set idrac.users.<index>.SNMPv3AuthenticationType <value>".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1016

Message: The specified user already exists. Duplicate user names are not allowed.
Detailed Description: iDRAC does not allow duplicate user names for each of the 16 users.
Recommended Response Action: Make sure that each of the 16 user names are unique.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1017

Message: Successfully modified the object value and the change is in pending state.
Detailed Description: Any staged operation requires a job and system reboot to apply the object values.
Recommended Response Action: To apply modified value, create a configuration job and reboot the system. To create the commit and reboot jobs, use "jobqueue" command. For more information about the "jobqueue" command, see RACADM help.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1018

Message: The specified object or syntax is invalid.
Detailed Description: This occurs when an incorrect syntax is used or an incorrect object is specified during the command invocation.
Recommended Response Action: Make sure to use the correct syntax and correct object names, and retry the operation. For information related to the corresponding group, see RACADM help or the RACADM Users Guide.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1019

Message: The specified object is not supported for the current system configuration.
Detailed Description: Some objects have dependencies on other objects that are required to perform a task. The specified object is not available because of such dependencies.
Recommended Response Action: Verify the object dependency using "racadm help <device class>.<groupname>.<objectname>", and retry the operation. For example, racadm help NIC.VndrConfigGroup.1.VirtWWPN.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1020

Message: No objects are available under the specified group for the current system configuration.
Detailed Description: Some objects have dependencies on other objects that are required to perform a task. The specified group does not contain any objects, because the dependent objects are not part of the current system configuration.
Recommended Response Action: Verify the dependencies of the objects under the specified group using "racadm help <device class>.<groupname>", and retry the operation. For example, "racadm help NIC.IscsiSecondTgtParams".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1021

Message: NIC objects are not available in the current system configuration.
Detailed Description: NIC objects are not available if NIC devices are not installed in the system, or if some iDRAC services are busy.
Recommended Response Action: Make sure the NIC devices are correctly installed in the system and retry the operation after the Collect System Inventory On Restart (CSIOR) feature has updated the system inventory. If the issue persists, contact your service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1023

Message: Unable to create the configuration job.
Detailed Description: Configuration jobs are created only if at least one object on the device or component (for example, NIC.Slot.1 or BIOS) has a pending value to be applied.
Recommended Response Action: Make sure that there is at least one object on the specified device or component that has a pending vlaue, and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1024

Message: Successfully scheduled a job.
Detailed Description: The pending value is applied during the next reboot of system.
Recommended Response Action: Verify the job status using "racadm jobqueue view -i JID_xxxxx" command.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1025

Message: The specified object is read-only and cannot be modified due to an object dependency.
Detailed Description: Some objects have dependencies on other objects that are required to perform a task. However, some of the objects are read-only because of the current system configuration and the values of the dependent objects.
Recommended Response Action: Verify the object dependency using "racadm help <device class>.<groupname>.<objectname>", and retry the opearation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1026

Message: A custom signing certificate does not exist.
Detailed Description: A custom signing certificate must be present in the system to delete or downlod the certificate.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1027

Message: Successfully sent the alert for the specified event to the configured destination.
Detailed Description: A test event was generated and the alert was successfully sent to the destination.
Recommended Response Action: Verify if the alerts were received by the configured tdestination. Otherwise, reconfigure the destination and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1028

Message: Unable to download the specified certificate type.
Detailed Description: The certificate cannot be downloaded if the certificate type specified is other than "1", "2", or "3".
Recommended Response Action: Make sure to specify either "1", "2", or "3" for the certificate type (-t) option, and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1029

Message: Unable to delete the specified certificate type.
Detailed Description: The certificate cannot be deleted if the certificate type specified is not "3".
Recommended Response Action: Make sure to specify "3" for the certificate type (-t) option, and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1030

Message: The custom signing certificate was deleted.
Detailed Description: The custom signing certificate present on iDRAC was deleted.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1031

Message: Unable to delete the custom signing certificate.
Detailed Description: The custom signing certificate on iDRAC cannot be deleted because of an internal error.
Recommended Response Action: Verify if iDRAC has a custom signing certificate. If it has the certificate, retry the operation. If the issue persists, contact your service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1032

Message

arg1 jobs was cancelled by the user.

Arguments

arg1 = Job ID or ALL

Detailed Description

The job specified in the message were cancelled.

Recommended Response Action

No response action is required

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1033

Message: Unable to retrieve the server component software inventory.
Detailed Description: The server component software inventory cannot be retrieved because of an internal error.
Recommended Response Action: Make sure to enable Collect System Inventory On Restart (CSIOR) feature, reboot the server, and retry the operation. If CSIOR is already enabled, restart iDRAC using "racadm racreset" command, and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1034

Message: This action will ungracefully turn off the server.
Detailed Description: This operation will cause the server to shutdown immediately. This may result in the applications losing data.
Recommended Response Action: Before continuing, exit all the programs running on this server, and make sure that there is no inbound and outbound traffic associated with this server. Inability to do so may prevent all the servers in the chassis from accessing the shared-storage devices for up to two minutes. To continue the operation, enter a -f at the end of command "racadm serveraction powerdown -f", and then retry.
Category: System Health
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1035

Message: There are no pending values to be cleared.
Detailed Description: The command is unable to clear the pending state for attributes of the specified component because there are no pending values.
Recommended Response Action: Make sure that there is at least one attribute on the specified device has a pending value, and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1036

Message: Successfully cleared pending attribute(s) for the group specified.
Detailed Description: Successfully cleared pending values for attributes in the group specified.
Recommended Response Action: To verify, run the RACADM command "racadm get group".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1037

Message: Unable to clear pending attribute(s).
Detailed Description: Unable to clear pending attribute(s). This may be because the FQDD entered is incorrect.
Recommended Response Action: Check that the FQDD entered is correct. View the Help information by running the RACADM command "racadm help clearpending".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1038

Message: Unable to clear pending values for the specified component.
Detailed Description: Unable to clear pending values for the specified component. This may be because there is an existing configuration job for the component.
Recommended Response Action: Make sure that a config job is not scheduled for this component. For more information, view the help command by running the RACADM command "racadm jobqueue help delete".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1039

Message: The subcommand entered is not supported on the specified server.
Detailed Description: The subcommand entered is not supported on the specified server.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1040

Message: Successfully accepted the RAID storage configuration operation. The change is in pending state.
Detailed Description: The requested RAID storage operation was successfully accepted and now must be applied by creating a RAID storage configuration job.
Recommended Response Action: To apply the configuration operation, create a configuration job, and then restart the server. To create the required commit and reboot jobs, run the jobqueue command. For more information about the jobqueue command, enter the RACADM command "racadm help jobqueue".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1041

Message: Successfully configured the Automatic Update (autoupdate) feature settings.
Detailed Description: Successfully configured the Automatic Update (autoupdate) feature settings.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1042

Message: Unable to configure the Automatic Update (autoupdate) feature settings. The required options are either invalid or not provided.
Detailed Description: One or more required options to configure the Automatic Update (autoupdate) feature are missing.
Recommended Response Action: For more information, view the help details by running the RACADM command "racadm help autoupdatescheduler".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1043

Message

Unable to configure the Automatic Update (autoupdate) feature settings. The option arg1 is either invalid or not provided.

Arguments

arg1 = option name

Detailed Description

The operation did not complete successfully because of an invalid value for the option identified in the message.

Recommended Response Action

Retry with a correct value for the option identified in the message. For more information, view the help details by running the RACADM command "racadm help autoupdatescheduler".

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1044

Message: The Automatic Update (autoupdate) feature is not enabled.
Detailed Description: The Automatic Update (autoupdate) feature is not enabled
Recommended Response Action: To enable, run the RACADM command "racadm set lifecyclecontroller.lcattributes.autoupdate 1".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1045

Message: Specifying ftp.dell.com as the catalog source for the Automatic Update feaure may result in frequent system firmware updates because the catalog on ftp.dell.com changes often.
Detailed Description: Individual component firmware updates may occur frequently and cause changes to the catalog on ftp.dell.com. Specifying ftp.dell.com as the catalog source for the Automatic Update feaure may result in frequent system firmware updates.
Recommended Response Action: Creating a custom repository using the Repository Manager tool allows control of the frequency of component firmware updates.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1046

Message: Unable to view the Automatic Update (autoupdate) feature settings because the feature has not been configured.
Detailed Description: Unable to view the Automatic Update (autoupdate) feature settings because the feature has not been configured.
Recommended Response Action: Configure the Automatic Update feature by running the RACADM command "racadm autoupdatescheduler create" with the desired option settings.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1047

Message: Successfully cleared the Automatic Update (autoupdate) feature settings.
Detailed Description: Successfully cleared the Automatic Update(autoupdate) feature settings.
Recommended Response Action: No response action is required
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1048

Message: Unable to clear the Automatic Update (autoupdate) feature settings because there is currently no configuration.
Detailed Description: The Automatic Update (autoupdate) feature settings must already exist in order to be cleared.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1049

Message: Successfully configured the Automatic Backup (autobackup) feature settings.
Detailed Description: Successfully configured the Automatic Backup (autobackup) feature settings.
Recommended Response Action: No response action is required
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1050

Message: Unable to configure the Automatic Backup (autobackup) feature settings. The required options are either invalid or not provided.
Detailed Description: One or more required options to configure the Automatic Backup (autobackup) feature are missing.
Recommended Response Action: For more information, view the help details by running the RACADM command "racadm help systemconfig backup".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1051

Message

Unable to configure the Automatic Backup (autobackup) feature settings. The option arg1 is either invalid or not provided.

Arguments

arg1 = option name

Detailed Description

The operation did not complete successfully because of an invalid value for the option identified in the message.

Recommended Response Action

Retry with a correct value for the option identified in the message. For more information, view the help details by running the RACADM command "racadm help systemconfig backup".

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1052

Message: The Automatic Backup (autobackup) feature is not enabled.
Detailed Description: The Automatic Backup (autobackup) feature is not enabled.
Recommended Response Action: To enable, run the RACADM command "racadm set lifecyclecontroller.lcattributes.autobackup 1".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1053

Message: Unable to view the Automatic Backup (autobackup) feature settings because the feature has not been configured.
Detailed Description: Unable to view the Automatic Backup (autobackup) feature settings because the feature has not been configured.
Recommended Response Action: Configure the Automatic Backup feature by running the RACADM command "racadm systemconfig backup" with the desired option settings.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1054

Message: Successfully cleared the Automatic Backup (autobackup) feature settings.
Detailed Description: Successfully cleared the Automatic Backup (autobackup) feature settings.
Recommended Response Action: No response action is required
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1055

Message: Unable to clear the Automatic Backup (autobackup) feature settings because there is currently no configuration.
Detailed Description: The Automatic Backup (autobackup) feature settings must already exist in order to be cleared.
Recommended Response Action: No response action is required
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1056

Message: Rollback operation initiated successfully.
Detailed Description: The requested firmware Rollback operation was initiated successfully.
Recommended Response Action: No response action is required
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1057

Message: Rollback operation did not complete successfully. The component identifier specified is not valid or does not have a rollback firmware image available.
Detailed Description: Rollback operation did not complete successfully. The component identifier (FQDD) specified in the operation is not valid or does not have a Rollback firmware image available.
Recommended Response Action: Run the RACADM command "racadm swinventory" to see the list of Rollback firmware images available and the corresponding component identifier (FQDD).
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1058

Message: Rollback operation did not complete successfully because Lifecycle Controller is disabled.
Detailed Description: The requested firmware Rollback operation did not complete successfully because Lifecycle Controller is disabled.
Recommended Response Action: Run the RACADM command "racadm set LifecycleController.LCAttributes.LifecycleControllerState 1" to enable Lifecycle Controller, and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1059

Message: Rollback operation could not be performed because another firmware update job is running.
Detailed Description: The requested firmware rollback operation could not be performed because another firmware update job is running or being scheduled.
Recommended Response Action: Wait until the existing firmware update jobs are completed or scheduled before retrying the operation. To monitor the status of the existing jobs, run the RACADM command "racadm jobqueue view". If the issue persists, restart the iDRAC and then retry the operation after the iDRAC has finished restarting.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1060

Message: System inventory may not becurrent because the Collect System Inventory On Restart (CSIOR) feature is disabled.
Detailed Description: The system inventory information may not be current because the Collect System Inventory On Restart (CSIOR) feature is disabled.
Recommended Response Action: To enable the CSIOR feature, run the RACADM command "racadm set LifecycleController.LCAttributes.CollectSystemInventoryOnRestart 1". Then restart the server to cause system inventory information to be collected.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1061

Message: SystemErase operation initiated successfully.
Detailed Description: The requested SystemErase operation was initiated successfully.
Recommended Response Action: Check the job status by running the RACADM command: "racadm jobqueue view -i <JobID>".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1062

Message: Unable to initiate the SystemErase operation. The component identifier specified is not valid.
Detailed Description: Unable to initiate the requested SystemErase operation. The component identifier specified is not valid.
Recommended Response Action: Run the RACADM command "racadm help systemerase" to see the list of supported components.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1063

Message: Unable to initiate the SystemErase operation because Lifecycle Controller is disabled.
Detailed Description: Unable to initiate the SystemErase operation because Lifecycle Controller is disabled.
Recommended Response Action: Run the RACADM command "racadm set LifecycleController.LCAttributes.LifecycleControllerState 1" to enable Lifecycle Controller, and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1064

Message: Unable to initiate the SystemErase operation because another instance of SystemErase job is already in progress.
Detailed Description: Unable to initiate the requested SystemErase operation because another SystemErase job is already in progress.
Recommended Response Action: To check the job status, run the RACADM command "racadm jobqueue view" and retry the operation after the current SystemErase operation has completed.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1065

Message: Unable to initiate the SystemErase operation because iDRAC encountered an internal issue.
Detailed Description: Unable to initiate the SystemErase operation because iDRAC encountered an internal issue.
Recommended Response Action: Retry the operation. If the issue persists, restart the iDRAC and then retry the operation after the iDRAC has finished restarting.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1067

Message

Unable to set the minimum non critical threshold value of arg1 , because the value entered is lesser than, or equal to the minimum critical threshold value.

Arguments

arg1 = System Board Inlet Temp

Detailed Description

The minimum non critical threshold value identified in the message cannot be set, because the value entered is lesser than, or equal to the minimum critical threshold value.

Recommended Response Action

Check the minimum critical threshold level using an appropriate RACADM command. For example, to view the minimum threshold value of a sensor, run the racadm getsensorinfo command at the command line interface, and then retry the operation. For more information about other RACADM commands, run the racadm help command.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1068

Message

Unable to set minimum non critical threshold value of arg1 , because the value entered is greater than, or equal to the maximum non critical threshold value.

Arguments

arg1 = System Board Inlet Temp

Detailed Description

The minimum non critical threshold value identified in the message cannot be set, because the value entered is greater than, or equal to the maximum non critical threshold value.

Recommended Response Action

Check the maximum non critical threshold level using an appropriate RACADM command. For example, to view the maximum non critical threshold value of a sensor, run the racadm getsensorinfo command at the command line interface, and then retry the operation. For more information about other RACADM commands, run the racadm help command.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1069

Message

Unable to set minimum non critical threshold value of arg1 , because the value entered is greater than, or equal to the maximum critical threshold value.

Arguments

arg1 = System Board Inlet Temp

Detailed Description

The minimum non critical threshold value identified in the message cannot be set, because the value entered is greater than, or equal to the maximum critical threshold value.

Recommended Response Action

Check the maximum critical threshold level using an appropriate RACADM command. For example, to view the maximum critical threshold value of a sensor, run the racadm getsensorinfo command at the command line interface, and then retry the operation. For more information about other RACADM commands, run the racadm help command.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1070

Message

Unable to set the maximum non critical threshold value of arg1 , because the value entered is greater than, or equal to the maximum critical threshold value.

Arguments

arg1 = System Board Inlet Temp

Detailed Description

The maximum non critical threshold value identified in the message cannot be set, because the value entered is greater than or equal to the maximum critical threshold value.

Recommended Response Action

Check the maximum critical threshold level using an appropriate RACADM command. For example, to view the maximum critical threshold value of a sensor, run the racadm getsensorinfo command at the command line interface, and then retry the operation. For more information about other RACADM commands, run the racadm help command.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1071

Message

Unable to set maximum non critical threshold value of arg1 , because the value entered is less than, or equal to the minimum non critical threshold value.

Arguments

arg1 = System Board Inlet Temp

Detailed Description

The maximum non critical threshold value identified in the message cannot be set, because the value entered is less than or equal to the minimum non critical threshold value.

Recommended Response Action

Check the minimum non critical threshold level using an appropriate RACADM command. For example, to view the minimum non critical threshold value of a sensor, run the racadm getsensorinfo command at the command line interface, and then retry the operation. For more information about other RACADM commands, run the racadm help command.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1072

Message

Unable to set maximum non critical threshold value of arg1 , because the value entered is less than, or equal to the minimum critical threshold value.

Arguments

arg1 = System Board Inlet Temp

Detailed Description

The maximum non critical threshold value identified in the message cannot be set, because the value entered is less than or equal to the minimum critical threshold value.

Recommended Response Action

Check the minimum critical threshold level using an appropriate RACADM command. For example, to view the minimum critical threshold value of a sensor, run the racadm getsensorinfo command at the command line interface, and then retry the operation. For more information about other RACADM commands, run the racadm help command.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1073

Message

Unable to reset the threshold value of sensor arg1 because the capability to reset this sensor threshold value is not supported.

Arguments

arg1 = sensor name

Detailed Description

The threshold value of the sensor identified in the message cannot be successfully set because the capability reset the sensor threshold value is not supported.

Recommended Response Action

No response action is required. For more information about resetting the threshold level of a sensor, run the "racadm getsensorinfo" command at the command line interface (CLI), and then retry the operation.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1109

Message: Unable to run the command, because an incorrect Share type is entered.
Detailed Description: Unable to run the command, because an incorrect Share type was entered.
Recommended Response Action: Enter an appropriate Share location of the following types: FTP, NFS, or CIFS. For more information, run the "racadm help update" command.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1110

Message: Unable to run the command, because an incorrect Proxy port number was entered.
Detailed Description: Unable to run the command, because an incorrect Proxy port number was entered. The Proxy port value must be a positive integer.
Recommended Response Action: Enter only numbers for a Proxy port value.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1111

Message: Unable to delete the pending values or operations of the specified device.
Detailed Description: Unable to clear pending values or operations from the specified storage device because there are no pending operations for the specified device.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1112

Message: Unable to delete the pending values for the specified device because the iDRAC internal storage is in use by a currently running job.
Detailed Description: Unable to clear the pending state from the attributes for a RAID object. A job is currently running and iDRAC internal storage is in use.
Recommended Response Action: Retry the operation after any currently running jobs have completed. Jobs can be monitored by running the racadm command "racadm jobqueue view".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1113

Message: Unable to perform the preview operation because the options -b, -c, -w, and -s must not be used with the --preview option.
Detailed Description: The configuration XML preview operation cannot be executed because the -b, -s, and -w options must not be used with the --preview option.
Recommended Response Action: Remove the -b, -w, and -s options wihen using the --preview option and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1114

Message

Configuration XML file preview operation job is initiated. Job ID = arg1

Arguments

arg1 = job ID

Detailed Description

The configuration XML preview operation was successfully initiatied and has generated a job with the job ID identified in the message.

Recommended Response Action

Monitor the status of the preview operation job by running the racadm command "racadm jobqueue view -i <job ID>".

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1115

Message: Unable to run the command, because of insufficient user privileges.
Detailed Description: The command could not be successfully run, because of insufficient privileges for the username supplied.
Recommended Response Action: Make sure that you have appropriate privileges, and then retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1116

Message: Unable to run the command, because the restart flag entered is incorrect.
Detailed Description: The command could not be successfully run, because an incorrect "restart flag" value was entered in the command.
Recommended Response Action: Enter a correct flag value. The recommended values are "true" and "false". Make sure that you have entered the correct value, and then retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1117

Message: Unable to run the command.
Detailed Description: The operation specified in the command could not be successfully completed.
Recommended Response Action: Retry the operation after 2 minutes. If the problem persists, contact your service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1118

Message: Successfully initiated the update operation specified in the command.
Detailed Description: Successfully initiated the update operation specified in the command.
Recommended Response Action: To know about the status of a command that is initiated, run the following command: racadm jobqueue view -I <job ID>.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1119

Message: Unable to generate a comparison report for the specified repository.
Detailed Description: The command could not be successfully run because of one or more of the following reasons: 1. The command does not have "--verifycatalog" in it. 2. The updates available on the repository are not applicable for the operation that is requested.
Recommended Response Action: To generate a comparison report, type "--verifycatalog" in the racadm command, and then retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1120

Message: Unable to run the command, because an incorrect Proxy type is entered.
Detailed Description: The command could not be successfully run, because an incorrect Proxy type value was entered for the -pt option.
Recommended Response Action: Make sure that you entered either "http" or "https" as the proxy type. Enter the correct type, and then retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1121

Message: Unable to run the command, because the data entered for connecting to the Proxy server is insufficient.
Detailed Description: The command could not be successfully run, because one or more values about the proxy server was not entered.
Recommended Response Action: Make sure that you enter the following data, and then retry the operation: - proxy server address - proxy user name - proxy password
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1122

Message: The specified group or object is not supported on the server.
Detailed Description: One or more of the group or component attributes specified in the operation do not exist on the targeted server.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1123

Message: Unable to perform the operation because Fibre Channel (FC) attributes are not available in the current server configuration.
Detailed Description: Fibre Channel (FC) objects are not available if Fibre Channel devices are not installed in the server, or if some iDRAC services are busy.
Recommended Response Action: Do the following: 1) Power off and remove AC or DC power from the server. 2) Make sure the Fibre Channel devices are correctly installed in the server. 3) Restart the server to allow the Collect System Inventory On Restart (CSIOR) feature to update the server inventory. 4) Retry the operation. If the issue persists, contact your service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1128

Message: The -l option must be specified if -u and -p options are used.
Detailed Description: Any operation involving remote share (CIFS) cannot continue if the location (-l option) is not specified. The -u and -p options represent the user name and password for the remote share, and -l represents the location of the remote share.
Recommended Response Action: Make sure to specify the location (-l option) of the remote share along with the user name and password, and retry the operation. To view the list of options that can used for the required subcommand, run the RACADM command "racadm help <subcommand>".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1129

Message: Unable to modify the BootOnce object.
Detailed Description: The BootOnce object could not be modified, because the FirstBootDevice object is set to either F10, F11, or BIOS.
Recommended Response Action: Configure the FirstBootDevice object to values other than F10, F11, or BIOS and retry the set operation for the BootOnce object. For more information about possible FirstBootDevice values, run the RACADM command "racadm help idrac.serverboot.firstbootdevice".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1130

Message: Unable to complete the operation. This feature is not supported on the currently-used platform.
Detailed Description: The requested operation could not be successfully completed because of an unsupported version of BIOS, USC, and/or iDRAC firmare.
Recommended Response Action: Verify whether or not a correct version of BIOS, Lifecycle Controller, and/or iDRAC firmware is installed. For more information on the appropriate firmware version required, refer to the RACADM Command Line Reference Guide. Also check if there is a limitation in terms of platforms such as monolithic or modular, and then retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1131

Message: iDRAC was successfully reset.
Detailed Description: The iDRAC was reset and is successfully restarted.
Recommended Response Action: None.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1132

Message: Unable to update the firmware. The value entered for an option is invalid.
Detailed Description: The firmware could not be successfully updated, because one or all of the following values are incorrect: a. logon ID b. IP address of TFTP or FTP server c. Full path of the firmware file.
Recommended Response Action: Run the racadm command "racadm help <subcommand>" to get more details about the various options applicable for this command and the values accepted by the command.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1133

Message: BIOSRTDRequested value is modified successfully.The BIOS reset to default values operation is pending a server restart.
Detailed Description: The BIOSRTDRequested attribute was modified successfully.The BIOS reset to default values operation is pending a server restart.
Recommended Response Action: To apply the BIOS default values, restart the server. After the server has restarted, the default BIOS values will be accessible from the iDRAC.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1134

Message: Unable to export the Lifecycle log data, because the export file size larger than 25MB and cannot be processed locally.
Detailed Description: Unable to export the Lifecycle log data, because the export file size larger than 25MB and cannot be processed locally.
Recommended Response Action: Export the Lifiecycle Log to a network file share. Using the RACADM command line utility, run the lclog export command with --complete option and related network file share parameters, and then retry the operation. For more information about the --complete option, run the "racadm help lclog export" command at the command line interface.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1135

Message: Unable to run the RACADM command because an internal instrumentation component has stopped functioning.
Detailed Description: The RACADM command could not be run because the internal instrumentation components are either busy or have stopped functioning.
Recommended Response Action: Wait for a minute for the internal instrumentation component to respond, and then retry the operation. If the issue persists, reset the iDRAC by pressing the System ID button for 15 seconds, wait for the iDRAC to finish restarting, and then retry the operation. If the issue continues to persist, contact your service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1136

Message: Remote unattended diagnostic execution operation initiated.
Detailed Description: The remote unattended diagnostic execution operation is initiated.
Recommended Response Action: Using the RACADM command line interface, run the "racadm jobqueue view -i <job id>" command to view the status of the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1137

Message: Remote unattended diagnostic results export operation initiated.
Detailed Description: Remote unattended diagnostic results export operation initiated.
Recommended Response Action: Using the RACADM command line interface, run the "racadm jobqueue view -i <job id>" command to view the status of the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1138

Message: Unable to export the diagnostics results because the results do not exist.
Detailed Description: Unable to export the remote diagnostics results because the remote diagnostics results have not been generated.
Recommended Response Action: Using the RACADM command line interface, run the "racadm diagnostics run" command to make sure that the diagnostics results are available, and then retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1139

Message: The entered option is not supported by the interface.
Detailed Description: The requested file can be exported from the firmware racadm only to a remote file share.
Recommended Response Action: Create a remote file share to export the file or use remote or local racadm to export to the file system that is accessible by the racadm executable.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1140

Message: File name is not required to export the Technical Support Report (TSR) to a remote share.
Detailed Description: The file name cannot be specified when the Technical Support Report (TSR) is exported to a remote share.
Recommended Response Action: Run the command without using the -f option. For more information on exporting Technical Support Report (TSR), run the command racadm help techsupreport export.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1141

Message: The iDRAC firmware rollback operation was initiated.
Detailed Description: The iDRAC firmware rollback operation was initiated.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1142

Message: Unable to start the Remote Diagnostics operation because the Expiration Time entered (difference between Start Time and Expiration Time) is less than five minutes.
Detailed Description: The Remote diagnostic operation cannot be performed because the difference between "Start Time" and "Expiration Time" is less than 5 minutes.
Recommended Response Action: Make sure that the Expiration Time is greater than five minutes, and then retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1143

Message

Configuration results are not applicable for the job type for Job: arg1 .

Arguments

arg1 = job ID

Detailed Description

The job identified in the message is not a configuration job, a configuration XML import or preview type job that generates configuration results.

Recommended Response Action

No response action is required.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1144

Message

The Job: arg1 is invalid or is not present in the job queue and a related Lifecycle Log entry is not found.

Arguments

arg1 = job ID

Detailed Description

No configuration results information is available for the job ID identified in the message because the job ID is invalid or is not present in the job queue and a related Lifecycle Log entry is not found.

Recommended Response Action

Check the job ID identified in the message and retry the operation with a valid job ID. To check valid job IDs in the current job queue, using RACADM, run the command "racadm jobqueue view".

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1145

Message: The entered log type is invalid.
Detailed Description: The value entered for the -t option is invalid.
Recommended Response Action: Check help text for the list of valid log types and retry the operation by entering a valid log type.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1146

Message: Unable to set the SNMPv3 username because SNMPv3 is not enabled for the specified user on iDRAC.
Detailed Description: The SNMPv3 username cannot be set because SNMPv3 is not enabled for the specified user on iDRAC.
Recommended Response Action: Enable SNMPv3 for the specified user by running the command "racadm set iDRAC.Users.<user index>.SNMPv3Enable 1", and then retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1147

Message: Unable to set the SNMPv3 username entered in the command because the username is not present or enabled on iDRAC.
Detailed Description: The SNMPv3 user cannot be set because the user with the entered username for the SNMPv3 group is not present or enabled on iDRAC.
Recommended Response Action: Make sure the specified username is present on iDRAC and enabled, and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1150

Message: Unable to complete the export operation.
Detailed Description: The export operation did not be complete successfully.
Recommended Response Action: Retry the export operation after five minutes.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1151

Message: The export operation is unsuccessful.
Detailed Description: The export operation did not complete successfully.
Recommended Response Action: Run the RACADM techsupreport collect command again and then retry the export operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1152

Message: The export operation completed successfully.
Detailed Description: The export operation completed successfully.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1153

Message: The time stamp is not available to display.
Detailed Description: The time stamp was not recorded for the previous techsupreport collect operation.
Recommended Response Action: Run the RACADM techsupreport collect command. After the techsupreport collect operation completes, run the RACADM getupdatetime command.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1154

Message: The requested operation is initiated.
Detailed Description: The requested techsupreport collect or export operation is initiated.
Recommended Response Action: Run the RACADM jobqueue sub-command, using the job id to check the status of the requested operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1155

Message: Unable to complete the operation because Lifecycle Controller is disabled.
Detailed Description: The operation was not completed because Lifecycle Controller is disabled.
Recommended Response Action: Enable the Lifecycle Controller and retry the operation. To enable Lifecycle Controller, run the command racadm set LifeCycleController.LCAttributes.LifecycleControllerState 1.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1156

Message: Unable to display the information about the server network interfaces.
Detailed Description: The server network interface information cannot be received because the iDRAC Service Module is not installed or not runing on the server operating system (OS) or collection of the OS data is disabled.
Recommended Response Action: Run the command racadm get iDRAC.ServiceModule to check if iDRAC Service Module is installed and running on the server operation system, and the collection of the OS data is enabled.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1157

Message: Unable to find the specified FQDD.
Detailed Description: The specified FQDD is invalid.
Recommended Response Action: Verify whether or not the entered FQDD is valid. Run the command racadm gethostnetworkinterfaces for the list of valid FQDDs.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1158

Message: The requested number of log entries exceeds the limit.
Detailed Description: The requested number of Lifecycle log entries exceed the limit and cannot be displayed. The remote RACADM operation may time out before retrieving all the log entries.
Recommended Response Action: Retrieve a smaller number of log entries using remote RACADM or use firmware or local RACADM to view all the log entries. To retrieve a limited number of log entries, use the -n option. For example, to view the last 10 log entries, run the command racadm lclog view -n 10.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1159

Message: Unable to get the requested data from iDRAC.
Detailed Description: The data cannot be retrieved from iDRAC because Lifecycle Controller is disabled or a DUP update is in progress.
Recommended Response Action: Do the following: 1) Check if a DUP fw update is progress and wait until it is finished. 2) Make sure the Lifecycle Controller is Enabled. To enable Lifecycle Controller, run the command racadm set LifeCycleController.LCAttributes.LifecycleControllerState 1. 3) Retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1160

Message

Unable to set USB group objects because of insufficient privilege for user account arg1 .

Arguments

arg1 = username

Detailed Description

Unable to set USB group objects because the user account identified in the message does not have the System Control privilege, which is required for this operation.

Recommended Response Action

Contact the iDRAC system administrator and get the System Control privilege added to the account identified in the message or use account credentials that have System Control privilege and retry the operation.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1161

Message: Unable to initiate the techsupreport collect operation for the Tech Support Report (TSR) because the iDRAC Service Module (iSM) is not running.
Detailed Description: Unable to initiate the techsupreport collect operation because the iDRAC Service Module (iSM) is not running.
Recommended Response Action: Run the command racadm get iDRAC.ServiceModule to make sure that iDRAC Service Module is installed and running on the server operation system (OS) and also to verify that the collection of the server OS data is enabled.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1162

Message: Unable to initiate the techsupreport collect operation for the Tech Support Report (TSR) because another collect operation is in progress.
Detailed Description: The requested techsupreport collect operation cannot be initiated because another techsupreport collect operation for the Tech Support Report (TSR) is in progress.
Recommended Response Action: Wait for the current collect operation to complete before initiating another collect operation. To view the status of the techsupreport collect operation, run the command racadm jobqueue view.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1163

Message

The peak utilization value of out-of-band performance monitoring sensor arg1 is successfully reset.

Arguments

arg1 = sensor name

Detailed Description

The peak utilization value of out-of-band performance monitoring sensor identified in the message is successfully reset.

Recommended Response Action

No response action required.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1164

Message: A remote diagnostics operation is currently running and not completed.
Detailed Description: A remote diagnostics operation is already under execution and another operation can be started only after the current execution is completed.
Recommended Response Action: Initiate another diagnostics operation only after the currently running operation is completed.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1165

Message: Unable to configure the port number that is entered for either http or https ports of the iDRAC Web server, because the port number is already in use.
Detailed Description: Unable to configure the port number that is entered for either http or https ports of the iDRAC Web server, because the port number is already in use.
Recommended Response Action: Enter a port number that is not already in use and retry the operation. If the issue persists, contact your service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1166

Message

Successfully initiated Configuration XML file preview operation that was invoked by arg1 .

Arguments

arg1 = user name

Detailed Description

The Configuration XML file preview operation was successfully initiated after it was invoked by the user name identfied in the message.

Recommended Response Action

No response action is required.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC1168

Message: The RACADM "getconfig" command will be deprecated in a future version of iDRAC firmware.
Detailed Description: The RACADM "getconfig" command will be deprecated in a future version of iDRAC firmware.
Recommended Response Action: Run the RACADM "racadm get" command to retrieve the iDRAC configuration parameters. For more information on the get command, run the RACADM command "racadm help get".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1169

Message: The RACADM "config" command will be deprecated in a future version of iDRAC firmware.
Detailed Description: The RACADM "config" command will be deprecated in a future version of iDRAC firmware.
Recommended Response Action: Run the RACADM "racadm set" command to configure the iDRAC configuration parameters. For more information on the set command, run the RACADM command "racadm help set".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1170

Message: Unable to find the SSL library in the default path.
Detailed Description: Unable to find the SSL library. This can be because, the library is not installed in the default path or no SSL library is installed.
Recommended Response Action: If a SSL library is not installed, install one and retry the operation. If a SSL library is installed, create a soft-link of the installed SSL library to "libssl.so" using the linux "ln" command and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1175

Message: Unable to change the user configuration because modifying the user configuration at index 1 is not allowed.
Detailed Description: The user configuration cannot be modified, because modification is not allowed at index 1.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1176

Message: Unable to generate the Certificate Signing Request (CSR) message because all the attributes in the iDRAC.Security group are not configured.
Detailed Description: The Certificate Signing Request (CSR) message cannot be generated because all the attributes in the iDRAC.Security group are not configured.
Recommended Response Action: Make sure that all the attributes in the iDRAC.Security group are configured. To get the list of attributes, run the following command "racadm get iDRAC.Security".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1177

Message: A USB device is attached to the iDRAC.
Detailed Description: A USB device is attached to the iDRAC and accessible from the iDRAC.
Recommended Response Action: No response action is required. To attach the USB device to the server instead of the iDRAC, remove the USB device from the front panel USB port, change the USB Management Port mode settings and then reinsert the USB device.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1178

Message: A USB device is attached to the iDRAC and a configuration XML import operation is in progress.
Detailed Description: A USB device is attached to the iDRAC and a configuration XML import operation is in progress.
Recommended Response Action: Wait until the configuration XML import operation has completed before attempting another operation. Verify the status of the configuration XML import operation by running the RACADM command "racadm jobqueue view".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1179

Message: Unable to complete requested operation because an Type A/A USB cable is connected to the front panel USB port and the iDRAC is emulating a NIC device.
Detailed Description: Unable to complete requested operation because a Type A/A USB cable is connected to the front panel USB port and the iDRAC is emulating a NIC device.
Recommended Response Action: To change the USB Management Port mode setting, remove the Type A/A USB cable from the front panel USB port and change the port mode settings.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1180

Message: A USB device is inserted in the front panel USB Management port and is in use by the server operating system.
Detailed Description: A USB Device inserted in the front panel USB Management port and is in use by the server operating system. The device needs to not be in use in order to change the port mode settings.
Recommended Response Action: Remove and reinsert the USB device and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1181

Message: Unable to change USB Management Port mode.
Detailed Description: USB Management Port state cannot be changed because of an unknown hardware or firmware issue.
Recommended Response Action: To change the Management Port mode settings do the following: If a device is present, remove and reinsert the USB device from the front panel USB Mangement port and retry the operation. If the issue persists restart the iDRAC and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1182

Message: Unable to retrieve information for the Power group or attribute because the server is not PMBus capable.
Detailed Description: The server instrumentation can not provide any information related to power because PMBus capability is not present or the PSU(s) with PMBus capability have been removed.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1183

Message: Unable to assign IP addresses 169.254.0.3 and 169.254.0.4 to the device OSBMC USBNIC because the IP addresses entered are reserved for the iDRAC Direct feature.
Detailed Description: The IP addresses 169.254.0.3 and 169.254.0.4 cannot be assigned to the device identified in the message because the IP addresses entered are reserved for the iDRAC Direct feature.
Recommended Response Action: Enter another appropriate IP address, and then retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1184

Message: The getuscvresion RACADM subcommand will be deprecated in a future release.
Detailed Description: The getuscvresion RACADM subcommand will be deprecated in a future release.
Recommended Response Action: Instead of getuscversion, run the getversion -f lc subcommand.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1185

Message: Unable to configure static IPv6 address because an invalid IPv6 address or IPv6 Gateway is entered.
Detailed Description: The static IPv6 address is not configured because an invalid IPv6 address or IPv6 Gateway is entered.
Recommended Response Action: Enter a valid IPv6 address and IPv6 Gateway, and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC1186

Message: 1000Mbps speed setting is Read Only and cannot be configured for the iDRAC NIC.
Detailed Description: Only possible configurations for the DRAC NIC are 10Mbps and 100 Mbps. For documentation with respect to this setting, refer to the racadm User Guide under cfgNetTuning group.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC802

Message: iDRAC time is set using Network Time Protocol.
Detailed Description: iDRAC time has been set through Network Time Protocol (NTP).
Recommended Response Action: No response action is required.
Category: Audit
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC913

Message: Unable to login to RAC using the specified address
Detailed Description: The management system could not login to the iDRAC.
Recommended Response Action: Verify whether the username and password given for the iDRAC are correct.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC914

Message: Value specified is invalid: Must be 0 (Off) or 1 (On).
Detailed Description: The specified value is not within the valid range. To set the LED state to off, enter 0. To set the LED state to on, enter 1.
Recommended Response Action: Set the numeric value to 0 (Off) or 1 (On).
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC915

Message: Unable to change auto-negotiation property for the NIC.
Detailed Description: The auto-negotiation property for the iDRAC NIC can be changed only if the NIC is in dedicated mode. To change the NIC mode to dedicated, an iDRAC Enterprise license is required.
Recommended Response Action: Change the NIC mode to dedicated mode by using "racadm set idrac.nic.selection <1 | Dedicated>", and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC916

Message: Value given exceeds the maximum threshold value.
Detailed Description: The value given is greater than the maximum threshold value.
Recommended Response Action: Set values lesser than the maximum threshold value. To view the maximum threshold value, run racadm get System.Power. Cap.MaxThreshold at the command prompt.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC917

Message: The syntax of the specified command is not correct.
Detailed Description: The syntax of the specified command is incorrect.
Recommended Response Action: See the command help text. To see the help text, run "racadm help <subcommand>".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC918

Message: Unable to get the inlet temperature data.
Detailed Description: Racadm unable to obtain the inlet temperature data. This happens if there is no data populated in the temperature tables or if the underlying instrumentation does not return valid values.
Recommended Response Action: Wait for the underlying instrumentation to populate the thermal tables. Retry the operation.
Category: System Health
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC919

Message: Copy to remote share unsuccessful. Remote share might be write protected.
Detailed Description: Racadm could not export the inlet temperature history file to the specified remote share. This is because the specified share may be write- protected.
Recommended Response Action: To export the file, change the permissions on the remote share. Else, create another share with write permissions.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC920

Message: This interface does not support the specified option.
Detailed Description: From firmware racadm, the inlet temperature history can be exported only to a remote file share.
Recommended Response Action: Create a remote file share to export the inlet temperature history. Else, use remote/local racadm to export to the file system accessible by the racadm executable.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC921

Message: The temperature history can be exported in XML or CSV format only.
Detailed Description: The file type specified (with the t parameter) is invalid. The temperature history can be exported in XML or CSV.
Recommended Response Action: Change the requested export file type to either XML or CSV. To do this, change the argument given to the t parameter. The argument given to the parameter is case-insensitive.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC922

Message: Specified path is too long.
Detailed Description: The specified path (specified with the l parameter) for the remote share is too long. This path should be less than 256 characters in length.
Recommended Response Action: Try the same command with a different remote share location, which is less than 256 characters in length.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC923

Message: The file path is too long.
Detailed Description: The specified file path (specified with the f parameter) is too long. This path should be less than 64 characters in length.
Recommended Response Action: Try the same command with a shorter file path (specified with the f parameter) which is less than 64 characters in length.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC924

Message: Inlet temperature history exported successfully.
Detailed Description: The inlet temperature history was successfully exported to the specified file.
Recommended Response Action: None.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC925

Message: Recurrence interval is not applicable for this subcategory.
Detailed Description: An alert recurrence cannot be set for the specified subcategory. The alert recurrence is applicable only to the TMPS subcategory.
Recommended Response Action: 1. Check if the alert recurrence is applicable to this subcategory. To check this run racadm eventfilters get. 2. To set the notifications for the specified subcategory, run the command without the -r option.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC926

Message: The recurrence interval needs to be an integer from 0 to 365.
Detailed Description: The value given for the recurrence interval is invalid. It has to be a value from 0 to 365.
Recommended Response Action: Change the argument of r to a value from 0 to 365 and then run the same command.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC927

Message: Recurrence value modified successfully.
Detailed Description: The recurrence value was successfully modified to the specified value.
Recommended Response Action: None.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC928

Message: Unable to modify the recurrence value.
Detailed Description: Racadm unable to set the recurrence value. This occurs if the underlying instrumentation do not set the value.
Recommended Response Action: Wait for a few minutes and retry the command. If the problem persists, contact the service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC929

Message: Invalid category or subcategory specified.
Detailed Description: The category or subcategory specified is incorrect. The recurrence interval is applicable only to the TMPS subcategory and system category.
Recommended Response Action: See the command help text, for a list of valid categories.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC930

Message: Unable to export the inlet temperature data.
Detailed Description: Racadm is currently unable to obtain the inlet temperature data. This happens if there is no data populated in the temperature tables or if the instrumentation does not return valid values.
Recommended Response Action: Wait for the instrumentation to populate the thermal tables. Retry the operation. If the problem persists, contact the service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC936

Message: Unable to change the hot spare property for the PSU.
Detailed Description: iDRAC cannot enable or disable the hot spare property, because the system has a non-PMBus PSU.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC937

Message

Successfully initiated configuration XML file import operation that was invoked by the arg1 .

Arguments

arg1 = user name

Detailed Description

The configuration XML file import operation was successfully initiated after it was invoked by the user specified in the message.

Recommended Response Action

No response action is required.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC938

Message

Successfully initiated configuration XML file export operation invoked by the arg1 .

Arguments

arg1 = user name

Detailed Description

The configuration XML file export operation was successfully initiated after it was invoked by the user specified in the message.

Recommended Response Action

No response action is required.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC939

Message: Unable to start the system configuration profile export or import operation.
Detailed Description: The request to perform a system profile export or import opeartion cannot be started because a firmware update operation is already in progress.
Recommended Response Action: Wait until the update operation is completed or cancel the update operation, and retry.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC940

Message: Unable to start the system configuration profile export or import operation.
Detailed Description: If an existing system profile import or export job is running, then a system configuration profile backup or restore opeartion cannot be started.
Recommended Response Action: Wait until the existing system profile export or import job is completed or cancel the job before retrying the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC941

Message: Successfully initiated the export operation. This operation may take several minutes to complete.
Detailed Description: A system configuration profile export operation may take several minutes to complete depending on the system configuration.
Recommended Response Action: Monitor the job status using "racadm jobqueue view -i <Job ID>".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC942

Message: Successfully initiated the import operation. This operation may take several minutes to complete and may cause multiple system restarts while device firmware and configuration are applied.
Detailed Description: The system configuration profile import operation is initiated. No other operations can be performed on the system while the system configuration server profile is being imported from the system configuration profile.
Recommended Response Action: Monitor the job status using "racadm jobqueue view -i <Job ID>".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC943

Message: Warning: Collect System Inventory On Restart (CSIOR) feature is disabled.
Detailed Description: The Collect System Inventory On Restart (CSIOR) feature is currently disabled. If the system inventory is not up-to-date, the system configuration profile that is being copied will not have the latest inventory information.
Recommended Response Action: To get latest inventory information, cancel the current export job, run "racadm set LifecycleController.LCAttributes.CollectSystemInventoryOnRestart 1" to enable CSIOR, and re-initiate the export operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC944

Message: Unable to create the configuration job.
Detailed Description: A configuration job cannot be created if Lifecycle Controller is disabled.
Recommended Response Action: Run "racadm set LifecycleController.LCAttributes.LifecycleControllerState 1" to enable Lifecycle Controller, and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC945

Message: Invalid object value specified.
Detailed Description: The dedicated NIC or shared NIC scan time value is not between 5 and 255 seconds.
Recommended Response Action: Make sure to set the scan time value between 5 and 255 seconds, and retry the operation. For more information, see RACADM help.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC946

Message: Unable to set the NIC to Auto Dedicated NIC mode.
Detailed Description: The "Auto Dedicated NIC" mode cannot be set for a NIC if the NIC selection mode is set to "Dedicated NIC".
Recommended Response Action: To set the NIC to Auto Dedicated NIC mode, set NIC selection mode to "Shared NIC", and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC947

Message: Invalid object value specified.
Detailed Description: The value used for the object set operation is invalid.
Recommended Response Action: Make sure to specify the value depending on the type of object. For more information, see RACADM help.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC948

Message: Unable to send the notification for the specified event to the configured destination.
Detailed Description: A test event notification for the specified message ID was not sent to the configured destination.
Recommended Response Action: Make sure to the use a valid message ID, set the required notification filter, and retry the operation. If the issue persists, contact your service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC949

Message: Successfully added a work note to the Lifecycle Log.
Detailed Description: The specified work note was added to the Lifecycle Log.
Recommended Response Action: View the work notes using the racadm lclog view c worknotes command.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC950

Message: Unable to add the work note to the Lifecycle Log.
Detailed Description: The work note cannot be added to the Lifecycle Log if iDRAC is archiving the older records in the Lifecycle Log.
Recommended Response Action: Wait for several minutes while iDRAC archives the older records, and then retry the operation. If the issue persists, contact your service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC951

Message: The number of characters entered for the work note exceeds the supported limit.
Detailed Description: Up to 256 characters are allowed for a work note.
Recommended Response Action: Do not exceed 256 characters in the work note, and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC952

Message: There is no free space to add new work notes to the Lifecycle Log.
Detailed Description: The allocated size for the Lifecycle Log entries has reached its maximum limit, and no further work notes can be added to the Lifecycle Log.
Recommended Response Action: Contact your service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC953

Message: Successfully added the comment.
Detailed Description: The comment was added to the specified entry in the Lifecycle Log.
Recommended Response Action: View the added comment using the racadm lclog view q <seq. no> -n 1 command.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC954

Message: The number of characters entered for the comment exceeds the supported limit.
Detailed Description: Up to 128 characters are allowed for a comment.
Recommended Response Action: Do not exceed 128 characters for the comment, and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC955

Message: Unable to retrieve the information related to the specified record in the Lifecycle Log.
Detailed Description: The specified record does not exist in the Lifecycle Log.
Recommended Response Action: Run the racadm lclog view -i command to get the sequence number of the records logged in the Lifeycle Log, and retry the command with a valid sequence number.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC956

Message: There is no free space to add new comments to the Lifecycle Log.
Detailed Description: The allocated size for the Lifecycle Log entries has reached its maximum limit, and no further comments can be added to the Lifecycle Log.
Recommended Response Action: Contact your service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC957

Message: An import or export operation is currently in progress.
Detailed Description: Another import or export operation cannot be started until the current operation is complete.
Recommended Response Action: Wait until the current import or export operation is complete before starting another operation. Use the racadm jobqueue view command to check the status of the current import or export operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC958

Message: Unable to start the import or export operation.
Detailed Description: An import or export operation cannot be started until the current update operation is complete.
Recommended Response Action: Wait for the current update operation to complete before starting another operation. Use the racadm jobqueue view command to check the status of the current update operation jobs.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC959

Message: Invalid file used for configuration XML file import operation.
Detailed Description: The content of the configuration XML file used for import is invalid because of incorrect modifications or content.
Recommended Response Action: Correct the modifications to the configuration XML file to be imported or specify the correct file, and retry the operation. Check the Lifecycle Log for more details.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC960

Message: Unable to find the specified configuration XML file for import.
Detailed Description: The configuration XML file specified for import cannot be located in the specified repository.
Recommended Response Action: Make sure the specified file name is correct and is located in the specified repository, and retry the operation. For more information about the syntax, run "racadm help set" to view RACADM help.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC961

Message: A pending or committed system configuration change exists.
Detailed Description: Another import operation cannot be started if an import operation that was performed earlier has some pending or commited configuration changes.
Recommended Response Action: Wait until the configuration changes are applied before starting another import operation. Use the racadm jobqueue view command to check the status of the current import operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC962

Message: Unable to continue with the operation because Lifecycle Controller is in recovery state,
Detailed Description: Lifecycle Controller must be enabled to run the operation.
Recommended Response Action: Enable the Lifecycle controller using the racadm set LifeCycleController.LCAttributes.LifecycleControllerState 1 command, and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC963

Message: Unable to retrieve the status of Lifecycle Controller.
Detailed Description: iDRAC is unable to read Lifecycle Controller status. Lifecycle Controller must be enabled to run the operation.
Recommended Response Action: Run the racadm get LifeCycleController.LCAttributes.LifecycleControllerState command to get the status of the Lifecycle Controller. If the issue persists, contact your service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC964

Message: Unable to perform the operation.
Detailed Description: The operation cannot be performed because of an internal error.
Recommended Response Action: Wait for some time before retrying the operation. If the issue persists, contact your service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC965

Message: The -l option must be specified if -u and -p are used.
Detailed Description: Any operation involving remote share (CIFS) cannot continue if the location (-l) is not specified. The u and p options represent the user name and password for the remote share, and -l represents the location of the remote share.
Recommended Response Action: Make sure to specify the location (-l) of the remote share along with the user name and password, and retry the operation. To view the list of options that can used for the required subcommand, use the racadm help <subcommand> command.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC966

Message: Unable to continue with the opearion because the user name or password is not specified.
Detailed Description: Any operation involving remote share (CIFS) cannot continue if user name, password, or both are not specified. The u and p options represent the user name and password for the remote share.
Recommended Response Action: Make sure to specify both user name and password for the remote share, and retry the operation. To view the list of options that can used for the required subcommand, use the racadm help <subcommand> command.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC967

Message: Exporting the configuration XML file to a local share is not supported when using Firmware RACADM.
Detailed Description: The configuration XML file can only be exported to a remote share while using Firmware RACADM.
Recommended Response Action: When using Firmware RACADM, make sure to export the configuration XML file to a remote share only.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC968

Message: Importing the configuration XML file from a local share is not supported when using Firmware RACADM.
Detailed Description: The configuration XML file cannot be imported from a client location when using Firmware RACADM.
Recommended Response Action: When using Firmware RACADM, make sure to import the configuration XML file from a remote share only.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC969

Message: Incorrect value specified for the shutdown option.
Detailed Description: The import operation cannot continue if the value specified for the shutdown option (-b) is incorrect. The supported values are "Graceful" and "Forced".
Recommended Response Action: Make sure to specify either "Graceful" or "Forced" for the shutdown (-b) option.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC970

Message: Incorrect value specified for the end power state option.
Detailed Description: The import operation cannot continue if the value specified for the end power state of the system option (-s) is incorrect. The supported values are "On" and "Off".
Recommended Response Action: Make sure to specify either "On" or "Off" for the end power state (-s) option.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC971

Message: Incorrect file type specified.
Detailed Description: The import or export operation cannot continue if the value specified for the file type is incorrect. The correct value for the file type is "xml" or "ini".
Recommended Response Action: Make sure to specify either "xml" or "ini" for the file type (-t) option. If no file type is specified, "ini" is used as default.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC972

Message: Insufficient privileges to run the configuration XML file import or export operations.
Detailed Description: Configuration XML import and export operations require the specified username to have administrator role privileges.
Recommended Response Action: Run the same command with a username that has an administrator role privileges.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC973

Message: The imported configuration XML file matches the current system configuration.
Detailed Description: The configuration XML file which was specified for import, had the same configuration as the current system configuration.
Recommended Response Action: Make any desired system configuration changes to the configuration XML file and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC974

Message: Invalid wait time specified.
Detailed Description: The value specified for the wait time (w) option is invalid. The valid range is 300 to 3600 seconds.
Recommended Response Action: Make sure to specify a valid wait time (-w) option and retry the command. The range of supported values are 300 to 3600 seconds.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC975

Message: Invalid share type specified.
Detailed Description: The share type specified using the l parameter is invalid. Only CIFS or NFS share types are supported for this operation.
Recommended Response Action: See the subcommand help text for supported share types.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC976

Message: Export configuration XML file operation initiated.
Detailed Description: The configuration XML file export operation was initiated.
Recommended Response Action: Use the racadm jobqueue view i <Job ID> command to view the status of the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC977

Message: Import configuration XML file operation initiated.
Detailed Description: The configuration XML file import operation was initiated.
Recommended Response Action: Use the racadm jobqueue view i <Job ID> command to view the status of the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC978

Message: Unsupported Lifecycle Controller firmware version detected.
Detailed Description: The Lifecycle Controller firmware version on the target system does not support the configuration XML file import or export operations.
Recommended Response Action: Update to the latest Lifecycle Controller firmware and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC979

Message: Successfully uploaded the custom signing certificate to iDRAC.
Detailed Description: The custom signing certificate was extracted from the Public Key Cryptography Standards version 12 (PKCS12) file and applied to the system configuration.
Recommended Response Action: No response action required.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC981

Message: The type of certificate specified does not require a passphrase.
Detailed Description: A passphrase is required only for passphrase protected certificate, which is specified using the value of 3 for the -t option.
Recommended Response Action: If the file being uploaded is passphrase protected, specify the file type as 3 using the -t option. If the file is not passphrase protected, retry the command, without specifying the -p option.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC982

Message: Invalid Public Key Cryptography Standards version 12 (PKCS12) file detected.
Detailed Description: The PKCS12 file provided is invalid, because it may not be in the correct format.
Recommended Response Action: For more details, contact the Certificate Authority.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC983

Message: Invalid passphrase provided for the Public Key Cryptography Standards version 12 (PKCS12) file.
Detailed Description: The Public Key Cryptography Standards version 12 (PKCS12) file is passphrase protected, and the passphrase provided is invalid.
Recommended Response Action: Specify the correct passphrase for the file using -p option.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC984

Message: Unable to upload the Public Key Cryptography Standards version 12 (PKCS12) file.
Detailed Description: iDRAC is unable to extract the custom signing certificate and the private key from the Public Key Cryptography Standards version 12 (PKCS12) file.
Recommended Response Action: Check if the specified file and passphrase are valid, and retry the operation. If the issue persists, contact your service provider.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC985

Message: Unable to configure the cfgServerBootOnce object.
Detailed Description: The object "cfgServerBootOnce" cannot be configured if the object "cfgServerFirstBootDevice" is set to F10, F11, or BIOS value.
Recommended Response Action: Change the value of the object "cfgServerFirstBootDevice" using the RACADM command "racadm config -g cfgServerInfo -o cfgServerFirstBootDevice<value other than F10, F11, and BIOS>", and retry configuring the object "cfgServerBootOnce".
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC986

Message: The "vmkey" sub-command is deprecated.
Detailed Description: The "vmkey" sub-command is deprecated, and the functionality is available using "vflashsd" sub-command.
Recommended Response Action: Use "vflashsd" sub-command instead of "vmkey". For more information about the sub-command, use "racadm help vflashsd" command.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC987

Message

Firmware update job for arg1 is initiated.

Arguments

arg1 = file name

Detailed Description

After initiating the firmware update job, the time taken to complete it depends on size of the update file.

Recommended Response Action

This firmware update job may take several minutes to complete depending on the component or firmware being updated. To view the progress of the job, use the "racadm jobqueue view" command.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC988

Message

Unable to initiate the arg1 firmware update.

Arguments

arg1 = file name

Detailed Description

A new firmware update job cannot be initiated while an existing firmware update job is still in one of these states: "New", "Downloading", or "Running".

Recommended Response Action

Wait until the existing firmware update jobs are completed or scheduled before retrying the operation. To monitor the status of the existing jobs, use the "racadm jobqueue view" command.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC989

Message

Unable to apply the arg1 firmware update.

Arguments

arg1 = file name

Detailed Description

Only Windows-based Update Package (.exe extension), iDRAC Firmware (.d7 extension), Personality Module Firmware (.pm extension), Lifecycle Controller firmware repair package (.usc) are supported for the firmware update operation.

Recommended Response Action

The file used for the operation is invalid. For the list of supported files, use "racadm help update". For the correct version of the file specific to the system, contact the service provider.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC990

Message

Unable to apply the arg1 update.

Arguments

arg1 = file name

Detailed Description

If Lifecycle Controller is disabled, the firmware update operation cannot continue.

Recommended Response Action

Enable Lifecycle Controller using the "racadm set lifecyclecontroller.lcattributes.lifecyclecontrollerstate 1" command, and retry the operation.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC991

Message: Unable to run the "jobqueue" command.
Detailed Description: The "jobqueue" command cannot be run, because the existing update jobs are transitioning to one of these states: "New", "Downloading", or "Running".
Recommended Response Action: Wait until the existing update jobs are completed before retrying the operation. To monitor the status of the existing jobs, use the "racadm jobqueue view" command.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC992

Message

Invalid job: arg1 .

Arguments

arg1 = job ID

Detailed Description

The job ID specified in the message is invalid or was already deleted.

Recommended Response Action

To monitor the current set of the jobs, use the "racadm jobqueue view" command.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC993

Message

The job: arg1 was deleted.

Arguments

arg1 = job ID

Detailed Description

The job ID specified in the message was deleted.

Recommended Response Action

No response action is required.

Category

Configuration

Subcategory

RAC = RAC Event

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

RAC994

Message: Unable to run the "jobqueue delete --all" command.
Detailed Description: The jobs cannot be deleted if they are in one of these states: "Scheduled" or "Running". However, all jobs in one of these states: "Completed" or "Failed" will be deleted.
Recommended Response Action: To monitor the job status, use the "racadm jobqueue view -i <job ID>", and delete the jobs one at a time using the "racadm jobqueue delete -i <job ID>" command.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC995

Message: Unable to retrieve the hardware inventory.
Detailed Description: The hardware inventory cannot be retrieved because of an internal error whether or not Collect System Inventory On Restart (CSIOR) is enabled or disabled.
Recommended Response Action: Make sure to enable Collect System Inventory On Restart (CSIOR) feature, reboot the system, and retry the operation. If CSIOR is already enabled, reboot iDRAC using "racadm racreset" command.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC996

Message: Unable to set the object value because the DNS RAC Name object is not configured.
Detailed Description: Unable to set the specified object value because the object DNS RAC Name is not configured.
Recommended Response Action: Configure DNS RAC name using "racadm set iDRAC.NIC.DNSRacName <Name>" command, and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC997

Message: The object DNSDomainFromDHCP cannot be enabled.
Detailed Description: The DHCP for Domian Name cannot be enabled if IPv4 and IPv4 DHCP or IPv6 and IPv6 AutoConfig is disabled.
Recommended Response Action: Make sure that IPv4 and IPv4 DHCP are enabled, or IPv6 and IPv6 AutoConfig are enabled
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC998

Message: IPv6 cannot be enabled.
Detailed Description: IPv6 cannot be enabled if iDRAC NIC is disabled.
Recommended Response Action: Enable iDRAC NIC using "racadm set iDRAC.NIC.Enable < 1 | Enabled >" command and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

RAC999

Message: The object DNSFromDHCP6 cannot be enabled.
Detailed Description: DNSFromDHCP6 cannot be enabled if iDRAC IPv6 AutoConfig is disabled.
Recommended Response Action: Enable IPv6 AutoConfig using "racadm set iDRAC.IPv6.AutoConfig < 1 | Enabled >" command, and retry the operation.
Category: Configuration
Subcategory: RAC = RAC Event
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

Welcome

Welcome to Dell

Event and Error Message Reference Guide For 13th Generation Dell PowerEdge Servers Version 1.0

RAC Event Messages

RAC001

RAC002

RAC003

RAC004

RAC005

RAC006

RAC007

RAC008

RAC009

RAC010

RAC0100

RAC0101

RAC0102

RAC0103

RAC0104

RAC0105

RAC0106

RAC0107

RAC0108

RAC011

RAC0113

RAC0115

RAC0116

RAC0117

RAC0118

RAC012

RAC0120

RAC0121

RAC0124

RAC0126

RAC0127

RAC0128

RAC0129

RAC013

RAC0130

RAC0131

RAC0132

RAC0133

RAC0134

RAC0135

RAC0136

RAC0137

RAC0138

RAC014

RAC0140

RAC0141

RAC0142

RAC0146

RAC0147

RAC0148

RAC0149

RAC015

RAC0150

RAC0151

RAC0152

RAC0153

RAC0154

RAC0155

RAC0156

RAC0158

RAC0159

RAC016

RAC0160

RAC0169

RAC017

RAC0171

RAC018

RAC0180

RAC019

RAC020

RAC0206

RAC0207

RAC0208

RAC0209

RAC021

RAC0211