Event and Error Message Reference Guide For 13th Generation Dell PowerEdge Servers Version 1.0

STOR003

Message: Missing parameter.
Detailed Description: Required parameter is missing.
Recommended Response Action: Refer to the RAID profile to determine required parameters.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR004

Message: Invalid parameter value.
Detailed Description: Provided parameter value is not valid.
Recommended Response Action: Refer to the RAID profile to determine the valid parameters values.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR006

Message: Unable to complete the operation.
Detailed Description: The operation could not be completed because of an issue with the management controller (either the iDRAC or the Chassis Management Controller (CMC)) that is managing the storage.
Recommended Response Action: Retry the operation. If the issue persists, contact your service provider.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR007

Message: Unable to allocate resources.
Detailed Description: The operation could not be completed because of insufficient memory space on the management controller (either the iDRAC or the Chassis Management Controller (CMC)) managing the storage.
Recommended Response Action: Retry the operation. If the issue persists, contact your service provider.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR009

Message: Physical disk FQDD did not identify a valid physical disk for the operation.
Detailed Description: Physical disk did not identify valid physical disk for the operation.
Recommended Response Action: Provide compatible physical disk with the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR010

Message: RAID level not supported on controller.
Detailed Description: The operation cannot be completed because the RAID level entered is not supported by the controller.
Recommended Response Action: Enter a valid RAID level and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0101

Message: No RAID controller is displayed.
Detailed Description: No RAID controller data to display. The system is powered off, no RAID controller is present in the system, or the RAID controller is not connected to the system.
Recommended Response Action: Check if the server has power, RAID controller is available, and that a RAID controller is connected to the system.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0102

Message: No batteries are displayed.
Detailed Description: No battery data to display. The system is powered off, batteries are not present on the system, batteries are not connected to the RAID controller, or the batteries are depleted.
Recommended Response Action: Check if the server has power, batteries are available, and batteries are connected to the RAID controller.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0103

Message: No physical disks are displayed.
Detailed Description: No physical disk data to display. The system is powered off, physical disks are not present on the system, or physical disks are not connected to the enclosure or backplane
Recommended Response Action: Check if the server has power, physical disks are available, and physical disks are connected to the enclosure or backplane.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0104

Message: No virtual disks are displayed.
Detailed Description: No virtual disk data to display. The system is powered off, physical disks are not present on the system, or virtual disks are not created.
Recommended Response Action: Check if the server has power, physical disks are available, and virtual disks are created.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0105

Message: No enclosures are displayed.
Detailed Description: No enclosure data to display. The system is powered off, enclosures are not present on the system, or enclosures are not connected to the RAID controllers.
Recommended Response Action: Check if the server has power, enclosures are available, and enclosures are connected to the RAID controllers.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0106

Message: Fans are not connected to enclosures or data about fans is unavailable.
Detailed Description: No fan data to display. The system is powered off, no fan enclosures are present in the system, or the fans are not connected to the enclosures.
Recommended Response Action: Check if the server has power, enclosure fan is available, and fan is connected to the enclosure.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0107

Message: EMMs are not connected to enclosures or data about EMMs is unavailable.
Detailed Description: No EMMs data to display. The system is powered off, no enclosure EMMs are present, or the EMMs are not connected to the enclosures.
Recommended Response Action: Check if the server has power, EMMs are available, and EMMs are connected to the enclosure.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0108

Message: Temperature probes are not connected to enclosures or data about temperature is unavailable.
Detailed Description: No temperature data to display. The system is powered off, no enclosure temperature probes are present in the system, or the temperature probes are not connected to the enclosures.
Recommended Response Action: Check if the server has power, enclosure temperature probe is available, and temperature probe is connected to the enclosure.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0109

Message: Power supply unit is not connected to the enclosure or data about power supply unit is unavailable.
Detailed Description: No power supply unit data to display. The system is powered off, no power supply unit is present in the system, or the power supply unit is not connected to the enclosure.
Recommended Response Action: Check if the server has power, enclosure power supply unit is available, and power supply unit is connected to the enclosure.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR011

Message: Stripe size not supported on controller.
Detailed Description: The operation cannot be completed because the stripe size entered is not supported by the controller.
Recommended Response Action: Enter a valid stripe size and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0110

Message: Invalid Fully Qualified Device Descriptor (FQDD).
Detailed Description: The specified Fully Qualified Device Descriptor (FQDDs) system component name is invalid.
Recommended Response Action: Verify that the correct Fully Qualified Device Descriptor (FQDD) system component name is specified. See the help text (The help text for the raid subcommand can be obtained by running "racadm help raid") or documentation for valid FQDD system component names.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0111

Message: Invalid reference key.
Detailed Description: The specified reference key is invalid.
Recommended Response Action: Verify that the correct reference key is specified. See the help text or documentation for valid reference keys.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR012

Message: Provided Physical disk not valid for this operation.
Detailed Description: One or more of the specified physical disks cannot be used for the operation requested. Physical disk protocol and media type, along with other physical disk characteristics like Secure Encryption and T10 protection, need to match the requirements of the requested operation.
Recommended Response Action: Make sure the specified physical disk has the appropriate protocol and media type for the requested operation. Specify a different physical disk with a state appropriate for the requested operation and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR013

Message: One or more storage device(s) are not in a state where the operation can be completed.
Detailed Description: One or more storage device(s) are in a state that prevents the operation from completing.
Recommended Response Action: Make sure the specified storage devices are in a state appropriate for the requested operation and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR015

Message: Maximum virtual disks allowed for this controller has been reached.
Detailed Description: A new virtual disk cannot be created because the maximum number of virtual disks are already created.
Recommended Response Action: A new virtual disk cannot be created until one is deleted.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR016

Message: The physical disk specified is not large enough to be a hot spare for this virtual disk.
Detailed Description: The physical disk drive cannot be assigned as the hot-spare of this virtual disk because the capacity of the physical disk is not sufficient.
Recommended Response Action: Specify a physical disk with a larger capacity or replace the specified physical disk with one with more capacity, and then retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR017

Message: The specified Virtual Disk is not valid for the operation.
Detailed Description: The virtual disk specified is not compatible with the requested operation or a specified operation parameter is not appropriate for the virtual disk type specified.
Recommended Response Action: Make sure the operation parameters are appropriate for the virtual disk type. Specify a compatible virtual disk for the requested operation and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR018

Message: No foreign drives detected.
Detailed Description: This operation did not detect any foreign drives. This may be because no foreign drives are present or the only foreign drives are in a secured state.
Recommended Response Action: If the only foreign drives present are in a secured state, run a secure erase operation on the drives and retry the operation. Otherwise the operation was not successful because there are no foreign drives.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR019

Message: The specified passphrase is not valid.
Detailed Description: The passphrase specified does not follow the passphrase character criteria of the controller character.
Recommended Response Action: Enter a passphrase that meets the passphrase character criteria of the controller, and then retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR020

Message: A controller key is already present.
Detailed Description: The controller key cannot be set because a key is already present.
Recommended Response Action: Delete the current key and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0200

Message: Array Manager is installed on the system.
Detailed Description: Installing Storage Services and Array Manager on the same system is not a supported configuration. Storage Services is not installed on a system where Array Manager is installed.
Recommended Response Action: Uninstall either Storage Services or Array Manager and retry the operation.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: 2135
Server Administrator Trap ID: 10300

STOR0201

Message: Unable to determine whether the system has the minimum required versions of the RAID controller drivers and firmware.
Detailed Description: Unable to determine whether the system has the minimum required versions of the RAID controller drivers.
Recommended Response Action: See the Readme file on the installation media for driver and firmware requirements. If Storage Services experiences performance problems, make sure that minimum supported versions of the drivers and firmware are installed. For a list of correct driver and firmware versions, contact the service provider.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: 2164
Server Administrator Trap ID: 10100

STOR0202

Message

The configuration file (Path: arg1 ) that contains firmware and driver information for arg2 is not updated or is incorrectly formatted to complete the comparison.

Arguments

arg1 = file path
arg2 = controller name

Detailed Description

Storage Services is unable to determine whether the system has the minimum required versions of the RAID controller firmware and drivers because a configuration file is not readable, corrupted, or has missing data.

Recommended Response Action

Reinstall Server Administrator and Storage Services.

Category

Storage

Subcategory

STOR = Storage

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

2166

Server Administrator Trap ID

75300

STOR0203

Message: The current operating system kernel version and the non-RAID SCSI driver version are older than the minimum required versions.
Detailed Description: The version of the operating system kernel and the driver do not meet the minimum requirements. Storage Services may not be able to display or perform storage management functions until the system meets the minimum requirements.
Recommended Response Action: See the Readme file on the installation media for operating system kernel and driver version requirements. Update the system to meet the minimum requirements and then reinstall Storage Services.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: 2167
Server Administrator Trap ID: 10300

STOR0204

Message: The non-RAID SCSI driver version is older than the minimum required version.
Detailed Description: The driver version does not meet the minimum requirements and Storage Services cannot perform the required operations until the minimum requirements are met.
Recommended Response Action: See the Readme file for the driver requirements and update the system to meet the minimum requirements and reinstall Storage Services.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: 2168
Server Administrator Trap ID: 10300

STOR0205

Message: Global rescan initiated for all storage components in the system.
Detailed Description: A rescan of all storage components in the system is initiated.
Recommended Response Action: No response action is required.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: 2261
Server Administrator Trap ID: 75100

STOR0206

Message: Smart thermal shutdown feature is enabled.
Detailed Description: The storage shutdown feature based on high ambient temperature (smart themal shutdown) is enabled.
Recommended Response Action: No response action is required.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: 2262
Server Administrator Trap ID: 10100

STOR0207

Message: Smart thermal shutdown feature is disabled.
Detailed Description: The storage shutdown feature based on high ambient temperature (smart themal shutdown) is disabled.
Recommended Response Action: No response action is required.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: 2263
Server Administrator Trap ID: 10100

STOR0208

Message: Protection policy has changed.
Detailed Description: A new protection policy is created or an existing protection policy is modified.
Recommended Response Action: No response action is required.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: 2287
Server Administrator Trap ID: 10100

STOR0209

Message: Unable to monitor or manage SAS components because the initialization sequence of the devices did not complete.
Detailed Description: The initialization sequence of SAS components did not complete during system startup.
Recommended Response Action: Do the following: 1) Make sure that the supported versions of the SAS drivers and firmware are installed. 2) Reboot the system. If problem persists, reinstall Server Administrator and Storage Services on the managed node to make sure all the required components are installed.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: 2314
Server Administrator Trap ID: 10400

STOR021

Message: The controller key is not present.
Detailed Description: The virtual disk cannot be secured because a controller key is not present.
Recommended Response Action: Set an appropriate controller key and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0210

Message

SCSI sense data ( arg1 ) received from arg2 .

Arguments

arg1 = sense info
arg2 = device name

Detailed Description

A SCSI device may have experienced an error that generated sense data after the device recovery.

Recommended Response Action

No response action is required.

Category

Storage

Subcategory

STOR = Storage

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

2095

Server Administrator Trap ID

75100;85100;90100

STOR0211

Message

The arg1 has returned to normal state.

Arguments

arg1 = device name

Detailed Description

The device identified in the message that was previously in an error state has returned to a normal state. For example, if an enclosure became too hot and subsequently cooled down, or if a degraded virtual disk returns to normal state.

Recommended Response Action

No response action is required.

Category

Storage

Subcategory

STOR = Storage

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

2121

Server Administrator Trap ID

75200;80200;85200;90200;95200;100200;105200;110200;115200;120100

STOR0212

Message

The arg1 has failed.

Arguments

arg1 = device name

Detailed Description

The device (physical disk or an enclosure) identified in the message has failed. The device (physical disk or an enclosure) failure was detected while performing a rescan. However, physical disk failures are also detected during a check consistency operation.

Recommended Response Action

Replace the identified device. A failed device is inidicated with a red color "X" status icon. Perform a rescan after replacing the failed device.

Category

Storage

Subcategory

STOR = Storage

Severity

Severity 1 (Critical)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

2048

Server Administrator Trap ID

75400;80400;85400;90400;95400;100400;105400;110400;115400;120400

STOR022

Message: The controller is not security capable.
Detailed Description: The specified controller does not have the capability to secure virtual disks.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR023

Message: Unable to perform configuration operations because a configuration job for the device already exists.
Detailed Description: Unable to perform configuration operations because a configuration job for the device already exists.
Recommended Response Action: Wait for the current job for the device to complete or cancel the current job before attempting more configuration operations on the device.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR024

Message: Unable to create a configuration job because a configuration job for the device already exists.
Detailed Description: Configuration changes for the specified device are already scheduled.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR025

Message: Unable to delete any pending configuration because the configuration job is already scheduled.
Detailed Description: The pending configuration cannot be deleted because the configuration job is already scheduled.
Recommended Response Action: Delete the current configuration job for the device to stop pending configuration changes.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR026

Message: A configuration job was not created because there are no pending configuration changes.
Detailed Description: A configuration job was not created because there are no pending configuration changes.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR027

Message: Virtual Disk name is not supported.
Detailed Description: Setting the Virtual disk name is not a valid operation on the specified controller.
Recommended Response Action: Do not specify the virtual disk name and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR028

Message: Virtual disk not found.
Detailed Description: The requested operation cannot be completed because the specified virtual disk is not found.
Recommended Response Action: Provide a valid virtual disk FQDD (Fully Qualified Device Descriptor) and retry the operation..
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR029

Message: Physical disk not found.
Detailed Description: The requested operation cannot be completed because the specified physical disk is not found.
Recommended Response Action: Provide a valid physical disk FQDD (Fully Qualified Device Descriptor) and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR030

Message: Controller not found.
Detailed Description: The requested operation cannot be completed because the specified controller is not found.
Recommended Response Action: Provide a valid controller FQDD (Fully Qualified Device Descriptor) and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR031

Message: Lifecycle Controller is not enabled.
Detailed Description: For 11G systems: System Services must be enabled to perform the requested operation. System Services has been disabled through the iDRAC configuration utility accessed by pressing CTRL+E on boot up or through a remote operation. For 12G systems: Lifecycle Controller must be enabled to perform the requested operation. Lifecycle Controller has been disabled by pressing F2 Setup, selecting iDRAC Configuration, and selecting Lifecycle Controller Settings on boot up or through a remote operation.
Recommended Response Action: For 11G systems: Use the iDRAC configuration utility to enable the System Services by pressing on the CTRL+E option on boot up at the targeted system. For 12G systems: Use F2 Setup, select iDRAC Configuration, and select Lifecycle Controller Settings, to enable the Lifecycle Controller on boot up of the targeted system.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR032

Message: Lifecycle Controller is currently in use.
Detailed Description: Lifecycle Controller is unable to gain access to internal storage because it is in use by another application or operation.
Recommended Response Action: Wait for current Lifecycle Controller operation to complete. Verify that the system is 1) Not currently in Lifecycle Controller Configuration utility 2) Not waiting for user intervention at F1/F2 POST error 3) Not in any of the device or controller Option ROMs and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR033

Message: Invalid parameter value for Start/Until Time.
Detailed Description: The requested operation cannot be completed because an invalid value is specified for Start/Until Time.
Recommended Response Action: Enter a valid Start/Until Time and retry the operation. For more information about the Start/Until Time, see the RAID Profile specification.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR034

Message: Invalid parameter value for RebootJobType.
Detailed Description: The requested operation cannot be completed because an invalid value is specified for RebootJobType.
Recommended Response Action: Enter a valid RebootJobType value and retry the operation. For more information about the RebootJobType parameter, see the RAID Profile specification.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR035

Message: Unable to perform operation because either the number of storage objects specified is insufficient or the storage objects are not in a required state to perform this operation.
Detailed Description: Unable to perform operation because either the number of storage objects specified is insufficient or the storage objects are not in a required state to perform this operation.
Recommended Response Action: Check the number and state of storage objects and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR037

Message

Missing required parameter arg1 .

Arguments

arg1 = parameter name

Detailed Description

Unable to complete the requested operation because one or more input parameters identified in the message are not specified.

Recommended Response Action

Enter all the required parameters and retry the operation.

Category

Configuration

Subcategory

STOR = Storage

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

STOR038

Message

Invalid parameter value for arg1 .

Arguments

arg1 = parameter name

Detailed Description

Unable to complete the requested operation because one or more input parameters identified in the message are not valid.

Recommended Response Action

Specify a valid value for identified parameter.

Category

Configuration

Subcategory

STOR = Storage

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

STOR039

Message: Mismatch in AttributeName and AttributeValue count.
Detailed Description: Unable to complete the requested operation because of a mismatch in the number of AttributeName and AttributeValue values specified.
Recommended Response Action: Specify a valid number of AttributeName and AttributeValue pair values and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR040

Message

Invalid AttributeName arg1 .

Arguments

arg1 = attribute name

Detailed Description

Unable to complete the requested operation because an invalid AttributeName value is specified.

Recommended Response Action

Specify a valid AttributeName value for the attribute identified in the message and retry the operation.

Category

Configuration

Subcategory

STOR = Storage

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

STOR041

Message

Invalid value for AttributeName arg1

Arguments

arg1 = attribute name

Detailed Description

Unable to complete the requested operation because an invalid value for the attribute identified in the message is specified.

Recommended Response Action

Specify a valid value for the attribute identified in the message and retry the operation.

Category

Configuration

Subcategory

STOR = Storage

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

STOR042

Message

Unsupported value for AttributeName arg1

Arguments

arg1 = attribute name

Detailed Description

Unable to complete the requested operation because the attribute value specified is not supported in the current configuration.

Recommended Response Action

Specify a value for the attribute identified in the message by using one of the possible values currently available for that attribute.

Category

Configuration

Subcategory

STOR = Storage

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

STOR043

Message: One or more selected physical disk drives are part of virtual disk that is not Secondary RAID Level 0.
Detailed Description: One or more physical disk drives selected for the operation are part of a virtual disk that is not Secondary RAID Level 0.
Recommended Response Action: This operation is not supported unless the previous virtual disk on the selected physical disk drives are deleted first. To perform the operation, delete any virtual disk on the selected physical disks drives and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR044

Message: All physical disks specified are not part of the same disk group.
Detailed Description: One or more physical disks specified to create virtual disk (VD) is not valid because it is not part of the same disk group.
Recommended Response Action: Enumerate existing virtual disks to find the physical disks of the same disk group. Specify physical disks that are of the same disk group and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR045

Message: StartingLBA and Size parameters are required to create a virtual disk.
Detailed Description: The specified physical disks have fragmented disk space, therefore StartingLBA and Size parameters are required to be specified in order to create a virtual disk.
Recommended Response Action: Specify StartingLBA and Size parameters and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR046

Message: The specified StartingLBA and Size values combination result in an overlapping virtual disk.
Detailed Description: Unable to complete the create virtual disk operation because the StartingLBA and Size value combination results in an overlapping virtual disk.
Recommended Response Action: Refer to the users guide to provide the correct StartingLBA and Size combination values.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR047

Message

Unable to change the value of attribute arg1 because it is ReadOnly.

Arguments

arg1 = attribute

Detailed Description

Unable to change the value of the attribute identified in the message because it is ReadOnly.

Recommended Response Action

No response action is required.

Category

Configuration

Subcategory

STOR = Storage

Severity

Severity 3 (Informational)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

STOR048

Message: Controller is not Dell Key Management capable.
Detailed Description: Either the controller or the firmware on the controller does not support the Dell Key Management feature.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR049

Message: Controller is in Local Key Management mode.
Detailed Description: The controller is in Local Key Management mode.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR050

Message: Controller is in Dell Key Management mode.
Detailed Description: The controller is in Local Key Management mode.
Recommended Response Action: No response action is required.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0501

Message: Unable to configure RAID.
Detailed Description: Unable to create a virtual disk due to unknown reasons.
Recommended Response Action: Do one of the following and retry the operation: 1) Exit the RAID Configuration wizard. 2) Update the RAID controller firmware to the latest version. 3) Reboot the system and press the <F10> key to re-enter Lifecycle Controller, and retry the operation.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0502

Message: Unable to launch RAID Configuration wizard.
Detailed Description: No RAID controller is installed on the system.
Recommended Response Action: Install the RAID controller and do the following: 1) Reboot the system. 2) Press the <F10> key to re-enter Lifecycle Controller. 3) Retry RAID configuration.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0503

Message: Successfully erased RAID configuration.
Detailed Description: Existing RAID configuration was successfully erased.
Recommended Response Action: No response action is required.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0504

Message: Successfully completed RAID operation.
Detailed Description: The RAID operation was successful.
Recommended Response Action: No response action is required.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0505

Message: Unable to delete virtual disks.
Detailed Description: Unable to delete the existing virtual disks for unknown reasons.
Recommended Response Action: Exit the RAID Configuration wizard and retry the operation. If the problem persists do the following: 1) Reboot the system. 2) Press the <F10> key to re-enter Lifecycle Controller. 3) Retry the operation.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0506

Message: Unable to create virtual disk.
Detailed Description: The physical disk is unreadable or the RAID controller is not responding.
Recommended Response Action: Exit Lifecycle Controller, press the <F10> key to re-enter Lifecycle Controller, and retry the operation. If the problem persists, replace the physical disk or update the RAID controller firmware to the latest version, and retry the operation.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0507

Message: Insufficient physical disk space on selected RAID controller.
Detailed Description: The RAID controller does not have sufficient number of initialized physical disks or adequate disk space to create the requested virtual disk.
Recommended Response Action: Connect additional physical disks to the RAID controller, initialize the physical disks, and retry the operation. To initialize the physical disks, reboot the system and select Option ROM during system startup.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0508

Message: No supported controllers present for RAID configuration.
Detailed Description: Unable to configure RAID as the supported RAID controller is not present.
Recommended Response Action: Install a supported RAID controller and the required number of physical disks for the RAID configuration, and retry the operation.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0509

Message: No RAID levels are supported.
Detailed Description: The controller does not have the minimum number of initialized disks to create a virtual disk.
Recommended Response Action: Connect required number of initialized physical disks to the RAID controller and retry the operation.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR051

Message: StartingLBA and Size value combination is greater than allowed by the physical disk size.
Detailed Description: The requested operation cannot be completed because the specified StartingLBA and Size value combination is greater than allowed by the physical disk size.
Recommended Response Action: Specify the Size value only and allow the instrumentation to calculate the StartingLBA value then retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0510

Message: Encryption configuration failed.
Detailed Description: Unable to apply the RAID controller encryption because RAID controller is not reponding.
Recommended Response Action: Retry the operation. If the problem persists, reboot the system or update the RAID controller firmware to the latest version and retry the operation.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0511

Message: Unable to change the encryption key.
Detailed Description: Unable to change the encryption key due to an internal error.
Recommended Response Action: Exit Lifecycle Controller, press the <F10> key to re-enter Lifecycle Controller, and retry the operation. If the problem persists, update the RAID controller firmware to the latest version and retry the operation.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0512

Message: Unable to apply the encryption key.
Detailed Description: Unable to apply the encryption key due to an internal error.
Recommended Response Action: Exit Lifecycle Controller, press the <F10> key to re-enter Lifecycle Controller, and retry the operation. If the problem persists, update the RAID controller firmware to the latest version and retry the operation.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0513

Message: Unable to encrypt virtual disks.
Detailed Description: Unable to encrypt unsecure virtual disks due to an internal error.
Recommended Response Action: Exit Lifecycle Controller, press the <F10> key to re-enter Lifecycle Controller, and retry the operation. If the problem persists, update the RAID controller firmware to the latest version and retry the operation.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0514

Message: Unable to initialize the selected physical disk drive(s).
Detailed Description: The physical disk drive(s) cannot be initialized because the selected RAID controller does not support this operation while in non-RAID mode.
Recommended Response Action: Do one of the following: 1) Select a controller that is in RAID mode and retry the operation. 2) Update the controller firmware to the latest version and retry the operation.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR052

Message: Attempt to exceed the number of supported of virtual disks on a controller or disk group.
Detailed Description: The maximum limit on the number of virtual disks that can be created on the specified controller or disk group has been reached.
Recommended Response Action: Refer to the specific controller users guide for information on the number of supported virtual disks allowed.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR053

Message: The controller key is not present. The key must be retrieved from the Dell Key Management Server.
Detailed Description: The system could not obtain a controller key from the Dell Key Management Server.
Recommended Response Action: For more information about obtaining a key, see Dell Key Manager or Lifecycle Controller Remote Services Guide availalbe at dell.com/support/manuals.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR054

Message: Controller is not CacheCade capable.
Detailed Description: The controller or the firmware on the controller does not support the CacheCade feature.
Recommended Response Action: Refer to the specific controller users guide for more information.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR058

Message: This operation is not supported on this device.
Detailed Description: The operation is not supported on the target device.
Recommended Response Action: For more information, see Lifecycle Controller-Remote Services documentation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR059

Message: The requested operation is not currently valid because there are no virtual disks on the controller.
Detailed Description: The requested operation cannot be completed because there are no virtual disks (VD) available on the specified controller.
Recommended Response Action: Create a virtual disk and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR060

Message: Configuration operations are not supported on the specified storage controller.
Detailed Description: The requested operation is not supported on the specified storage controller.
Recommended Response Action: For more information about supported operations, see the documentation specific for the targeted storage controller.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR061

Message: Initializing virtual disk is not supported on the RAID controller.
Detailed Description: The initializing virtual disk operation is not supported on the target device.
Recommended Response Action: For more information about supported operations, see the documentation specific for the targeted RAID controller or the Lifecycle Controller Remote Services Quick Start Guide.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR062

Message: One or more physical disks specified are full and cannot be used to create additional virtual disks.
Detailed Description: One or more physical disks specified are full and cannot be used to create additional virtual disks.
Recommended Response Action: Make sure all physical disks specified to create a virtual disk have the required amount of free space and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR063

Message: Unable to assign the specified virtual disk to multiple Virtual Adapters in single assignment mode.
Detailed Description: In order to prevent data loss, the system has prevented the assignment of a Virtual Disk to multiple Virtual Adapters because the clustered assignment mode is not enabled.
Recommended Response Action: Enable clustered assignment mode or unassign the virtual disk from the Virtual Adapter it is currently assigned to and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR064

Message: One or more physical disks specified for creating a virtual disk do not have the same block size.
Detailed Description: Unable to create the requested virtual disk because the physical disks specified did not have the same block size.
Recommended Response Action: Verify that the physical disks selected for creating the virtual disk have the same block size and retry the operation. The block size can be determined by reviewing the physical disk inventory and checking the BlockSize property for each physical disk.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR065

Message: One or more physical disks specified for creating a virtual disk are not T10 Protection Information capable.
Detailed Description: Unable to create the requested virtual disk because one or more specified physical disk(s) is not T10 Protection Information capable.
Recommended Response Action: Verify that the physical disks selected for creating a virtual disk are T10 Protection Information capable, and then retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR066

Message: Controller is not T10 Protection Information capable.
Detailed Description: The requested operation did not succeed because the selected RAID controller is not T10 Protection Information capable.
Recommended Response Action: Verify that the RAID controller selected for the operation is T10 Protection Information capable, and then retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR067

Message: Controller does not support uneven span RAID10 virtual disks.
Detailed Description: The operation did not succeed since the selected controller does not support creating uneven span RAID10 virtual disks.
Recommended Response Action: The selected controller is not capable of creating an uneven span RAID10 virtual disk. Specify the proper span length and span depth combination for creating RAID10 virtual disk on the selected controller, and then retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR068

Message: Unable to perform the requested RAID configuration because the Lifecycle Controller version on the server does not have the necessary capabilities.
Detailed Description: The requested RAID configuration operation did not succeed because the Lifecycle Controller version on the target server does not have the necessary capabilities.
Recommended Response Action: Check the Lifecycle Controller version on the target server and update it with the latest version available.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR069

Message

Unable to run the arg1 method, because the number of elements entered for VDPropNameArry and VDPropValueArray is unequal.

Arguments

arg1 = method name

Detailed Description

The method name identified in the message could not be successfully completed, because the number of elements entered for VDPropNameArry and VDPropValueArray is not equal.

Recommended Response Action

Enter equal number of elements (pair value), and then retry the operation.

Category

Configuration

Subcategory

STOR = Storage

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

STOR070

Message

Unable to run the WS-MAN method arg1 , because an invalid parameter arg2 is entered.

Arguments

arg1 = method name
arg2 = parameter name

Detailed Description

The method name identified in the message could not be successfully completed, because the number of elements entered for VDPropNameArry and VDPropValueArray is not equal.

Recommended Response Action

Enter a valid parameter, and then retry the operation. For more information about a valid parameter, refer to the SimpleRAIDProfile document available at Dell Tech Center http://en.community.dell.com/techcenter/extras/m/white_papers/20263535.aspx

Category

Configuration

Subcategory

STOR = Storage

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

STOR0701

Message: Storage objects are unavailable in the current system configuration.
Detailed Description: There are no RAID controllers, physical disks or virtual disks discovered by instrumentation that can be configured.
Recommended Response Action: Storage objects are unavailable in the current system configuration. Make sure that the storage devices are installed in the system, and then retry the operation after the Collect System Inventory On Restart (CSIOR) feature has updated the system inventory. If the issue persists, contact your service provider.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR0702

Message

The value entered for the arg1 option is invalid

Arguments

arg1 = option name

Detailed Description

The value entered for the option name identified in the message is invalid.

Recommended Response Action

For more information, run the RACADM command "racadm raid help createvd".

Category

Configuration

Subcategory

STOR = Storage

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

STOR071

Message

The specified Span Count is not valid for creating a RAID 10. Valid Span Counts are: arg1

Arguments

arg1 = valid span counts

Detailed Description

The configuration operation could not be performed because the specified span count is not valid.

Recommended Response Action

Enter a valid span count, and then retry the operation.

Category

Configuration

Subcategory

STOR = Storage

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

STOR072

Message: iDRAC Service Module (ISM) is either not present or not running on the server OS.
Detailed Description: The configuration operation could not be performed because it requires iDRAC Service Module (ISM) service to be present and running in the server Operating System.
Recommended Response Action: Make sure the iDRAC Servive Module (ISM) service is running on the server Operating System and then retry the operation. Refer to the iDRAC User Guide for installing and starting ISM.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR073

Message: The iDRAC Service Module version present on the server OS does not support the requested PCIe SSD (NVMe) device operation.
Detailed Description: The iDRAC Service Module version present on the server OS does not support the requested PCIe SSD (NVMe) device operation.
Recommended Response Action: Update the Dell iDRAC Service Module (ISM) to the version that supports the requested operation on the PCIe SSD (NVMe) device.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR074

Message: The requested RAID configuration operation is not allowed because the controller is currently in Non-RAID mode.
Detailed Description: The requested RAID configuration operation will not be allowed because the RAID controller is currently in Non-RAID mode.
Recommended Response Action: In order to perform a RAID configuration operation, change the controller mode to RAID and retry the operation. For switching to RAID mode using the F2 System Setup utility, go to Device Settings > "RAID Controller "> Controller Management > Advanced Controller Management > Switch to RAID mode.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR075

Message: The operation cannot be performed because the enclosure configuration mode (Split or Unified) change request is pending.
Detailed Description: The requested operation could not be completed because there is an operation pending to change the enclosure configuration mode (Split or Unified). This operation is exclusive because it involves changing the RAID backplane topology.
Recommended Response Action: Do one of the following: 1) Create a job to complete the pending enclosure mode change request operation, allow the job to complete, restart the server, and then retry the operation. 2) Cancel any pending operations on the RAID controller, and then retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR076

Message: Enclosure configuration mode (Split/Unified) cannot be changed because there are already pending operations.
Detailed Description: The requested operation could not be completed because at least one other pending operation was found on the RAID controller. This operation needs exclusivity because it involves changing RAID backplane topology.
Recommended Response Action: Do one of the following: 1) Create a job to complete the pending operations, allow the job to complete, and then retry the operation. 2) Cancel any pending operations on the RAID controller, and then retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR077

Message: Unable to change Patrol Read State since Patrol Read Mode is not set to Manual.
Detailed Description: A Patrol Read State change operation cannot be performed if the Patrol Read Mode is not set to Manual.
Recommended Response Action: Change the Patrol Read Mode to Manual before performing a Patrol Read State change operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR078

Message: The requested operation requires a reboot type that does not match the reboot type required for pending operations.
Detailed Description: The requested operation cannot be performed because it involves server reboot type which is different than the reboot type of pending operations. Combining operations with different reboot types for the same RAID controller is not supported by iDRAC.
Recommended Response Action: Cancel any pending operations on the RAID controller and then retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR079

Message: The device does not support this operation or is in a state that does not allow this operation.
Detailed Description: The requested operation cannot be performed because it is either not supported by the device or the device was not in the right state to perform the operation.
Recommended Response Action: Make sure the device supports the requested operation. If the operation is supported, then make sure the server is turned on and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR081

Message: The job could not be created because the reboot type selected for the job creation and the reboot type required for pending operations do not match.
Detailed Description: The job could not be created because the reboot type selected for the job creation and the reboot type required for pending operations do not match.
Recommended Response Action: Change the reboot type for job creation and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR082

Message: The operation cannot be stopped or cancelled because the operation is not currently running.
Detailed Description: The operation cannot be stopped or canceled because the operation is not currently running.
Recommended Response Action: Make sure the operation is running before attempting to cancel or stop the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR083

Message: The Physical Disk(s) specified are too small to create a Virtual Disk of the requested size.
Detailed Description: The Physical Disk(s) specified are too small to create a Virtual Disk of the requested size.
Recommended Response Action: Specify Phsyical Disk FQDD IDs of physical disk drive(s) that have a larger disk space, and retry the operation.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 2 (Warning)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR084

Message: Unable to create the job because another job is currently running
Detailed Description: The requested job cannot be run because another job is currently running. Two options for running jobs on multiple storage controllers are: 1) Run the jobs on each controller individually. Wait for each job to complete before starting the configuration and job creation on the next controller. 2) Schedule multiple jobs to run at a later time using the scheduling options.
Recommended Response Action: Make sure that the currently running job is completed, and then retry the operation. If necessary, recreate the configuration and the job. For information about running jobs on multiple storage controllers, see the iDRAC Online Help or iDRAC Users Guide.
Category: Configuration
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR089

Message: The storage configuration operation is successfully completed and the change is in pending state.
Detailed Description: The storage configuration operation is successfully completed and the change is in pending state.
Recommended Response Action: To apply the configuration operation immediately, create a configuration job using the --realtime option. To create the necessary real-time job, run the jobqueue command. For more information about jobqueue command, run the racadm help jobqueue command.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR090

Message: Unable to create a virtual disk because an invalid value of span count value is entered for the RAID level selected.
Detailed Description: Unable to create a virtual disk because an invalid value of span count value is entered for the RAID level selected.
Recommended Response Action: Enter a span count value (-sc option) that is appropriate for the RAID level selected. See the PERC Controller Users Guide for valid span count values. Retry the operation by running the RACADM storage createvd command with the appropriate options.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR092

Message: Unable to run the configuration operation on the controller because foreign configuration import operation is in progress.
Detailed Description: The requested configuration operation cannot be run because a foreign configuration import operation on the controller is already in progress.
Recommended Response Action: Wait for the import process to complete before running any configuration operation.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR093

Message: Unable to run the configuration operation because the controller is not available for the import process.
Detailed Description: The configuration operation cannot be performed because the controller is not available for import process.
Recommended Response Action: Make sure an operation is not pending on the controller. If an operation is pending, wait for the operation to complete or cancel the pending operation and then rety the operation. Refer to the storage controller documentation for compatibility information.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR094

Message: The storage configuration operation is successfully completed and the change is in pending state.
Detailed Description: The storage configuration operation is successfully completed and the change is in pending state.
Recommended Response Action: To apply the configuration operation immediately, create a configuration job using the --realTime option. To apply the configuration after restarting the server, create a configuration job using the -r option.To create the necessary real-time and restart jobs, run the jobqueue command. For more information about jobqueue command, run the racadm help jobqueue command.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR095

Message: Storage operation is successfully completed.
Detailed Description: Storage operation is successfully completed.
Recommended Response Action: No response action is required.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR096

Message: Unable to create a virtual disk because the disk space size value entered for the virtual disk is less than the lower limit value (100 MB).
Detailed Description: A virtual disk cannot be created because the disk space size value entered for the virtual disk is less than the lower limit value (100 MB).
Recommended Response Action: Enter a value (the -size option) equal or higher than 100 MB, and then retry the operation.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR097

Message: Unable to complete the operation because the memory size of the physical disk drive is less than the available or entered virtual disk size.
Detailed Description: A virtual disk cannot be created because the memory size of the physical disk drive is less than available or entered virtual disk size.
Recommended Response Action: Enter the FQDD of a physical disk drive that has a larger disk space, and then retry the operation. To view a list of physical disk drives and associated disk space, run the RACADM command "racadm storage get pdisks -o -p size". To view a list of virtual disks and associated size, run the RACADM command "racadm storage get vdisks -o -p size".
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR099

Message

Unable to find the FQDD arg1 because an invalid FQDD is entered or an operation is pending on the specified FQDD.

Arguments

arg1 = component FQDD

Detailed Description

The FQDD cannot be found because an invalid FQDD is entered or an operation is pending on the FQDD identified in the message.

Recommended Response Action

Do the following and then retry the operation: 1) Make sure the FQDD entered is valid. 2) Make sure an operation is not pending on the FQDD identified in the message. For more information refer to the RACADM Command Line Reference Guide.

Category

Storage

Subcategory

STOR = Storage

Severity

Severity 2 (Warning)

LCD Message

No LCD message display defined.

Initial Default

None

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

STOR1

Message

A device arg1 is in an unknown state.

Arguments

arg1 = device name

Detailed Description

The controller cannot communicate with a device. The state of the device cannot be determined. There may be a bad or loose cable, or a missing device, or a problem with the driver or firmware.

Recommended Response Action

See the storage hardware documentation for information on checking the cables. Check for problems with any enclosures attached to the system. Verify that the controller has a supported version of the driver and firmware. Rebooting the system may resolve this problem.

Category

Storage

Subcategory

STOR = Storage

Severity

Severity 2 (Warning)

Trap/EventID

4178

LCD Message

No LCD message display defined.

Initial Default

LC Log

Server Administrator Event ID

2265

Server Administrator Trap ID

75300;80300;85300;90300;95300;100300;105300;110300;115300;120300

STOR12

Message: Chassis is operating with a disabled RAID controller.
Detailed Description: One or more RAID controllers is disabled. This prevents Fault Tolerant mode from operating.
Recommended Response Action: No response action is required.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
Trap/EventID: 4179
LCD Message: No LCD message display defined.
Initial Default: None
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR2

Message

SCSI sense data arg1 .

Arguments

arg1 = args

Detailed Description

A SCSI device experienced an error, but may have recovered.

Recommended Response Action

No response action is required.

Category

Storage

Subcategory

STOR = Storage

Severity

Severity 3 (Informational)

Trap/EventID

4179

LCD Message

No LCD message display defined.

Initial Default

LC Log

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

STOR3

Message

CEM Storage Management has lost communication with the arg1 .

Arguments

arg1 = Controller Name

Detailed Description

Storage Management has lost communication with a controller. This may occur if the connectivity between the controller and iDRAC is disrupted or any underlying hardware problems are encountered.

Recommended Response Action

Reboot the system or iDRAC. If the problem is not resolved, contact technical support.

Category

Storage

Subcategory

STOR = Storage

Severity

Severity 1 (Critical)

Trap/EventID

4177

LCD Message

No LCD message display defined.

Initial Default

LC Log

Server Administrator Event ID

Not Applicable

Server Administrator Trap ID

Not Applicable

STOR4

Message: CEM Storage Management encountered internal error.
Detailed Description: There was a software problem in initializing the CEM storage management components. Storage inventory and monitoring will be affected.
Recommended Response Action: Reboot the system or iDRAC. If the problem is not resolved, contact technical support.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 1 (Critical)
Trap/EventID: 4177
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR5

Message

Redundancy lost. arg1

Arguments

arg1 = VD/Enclosure Name

Detailed Description

A virtual disk or enclosure has lost data redundancy. In the case of a virtual disk, one or more physical disks included in the virtual disk have failed. Due to the failed physical disk or disks, the virtual disk is no longer maintaining redundant (mirrored or parity) data. The failure of an additional physical disk will result in lost data. In the case of an enclosure, more than one enclosure component has failed. For example, the enclosure may have suffered the loss of all fans or all power supplies.

Recommended Response Action

Identify and replace the failed components. To identify the failed component, select the Storage object and click the Health subtab. The controller status displayed on the Health subtab indicates whether a controller has a failed or degraded component. Click the controller that displays a Warning or Failed status. This action displays the controller Health subtab which displays the status of the individual controller components. Continue clicking the components with a Warning or Failed status until you identify the failed component. See Storage Health for more information. See the enclosure documentation for information on replacing enclosure components and for other diagnostic information.

Category

Storage

Subcategory

STOR = Storage

Severity

Severity 2 (Warning)

Trap/EventID

4178

LCD Message

No LCD message display defined.

Initial Default

LC Log

Server Administrator Event ID

2123

Server Administrator Trap ID

130600

STOR6

Message: CEM Storage Management detected inventory change(s) after host re-boot.
Detailed Description: A comparison of storage inventory collected before and after the host re-boot/re-set. reports differences. There could have been some storage components added or removed when the host was powered down.
Recommended Response Action: No response action is required.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
Trap/EventID: 4179
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

STOR7

Message: The storage management instrumentation is performing an inventory refresh operation.
Detailed Description: The storage monitoring instrumentation detected a burst of events from underlying storage controllers. To overcome this overload condition, all the outstanding events have been purged and a fresh inventory will be performed automatically.
Recommended Response Action: No response action is required.
Category: Storage
Subcategory: STOR = Storage
Severity: Severity 3 (Informational)
Trap/EventID: 4179
LCD Message: No LCD message display defined.
Initial Default: LC Log
Server Administrator Event ID: Not Applicable
Server Administrator Trap ID: Not Applicable

Welcome

Welcome to Dell

Event and Error Message Reference Guide For 13th Generation Dell PowerEdge Servers Version 1.0

STOR Event Messages

STOR003

STOR004

STOR006

STOR007

STOR009

STOR010

STOR0101

STOR0102

STOR0103

STOR0104

STOR0105

STOR0106

STOR0107

STOR0108

STOR0109

STOR011

STOR0110

STOR0111

STOR012

STOR013

STOR015

STOR016

STOR017

STOR018

STOR019

STOR020

STOR0200

STOR0201

STOR0202

STOR0203

STOR0204

STOR0205

STOR0206

STOR0207

STOR0208

STOR0209

STOR021

STOR0210

STOR0211

STOR0212

STOR022

STOR023

STOR024

STOR025

STOR026

STOR027

STOR028

STOR029

STOR030

STOR031

STOR032

STOR033

STOR034

STOR035

STOR037

STOR038

STOR039

STOR040

STOR041

STOR042

STOR043

STOR044

STOR045

STOR046

STOR047

STOR048

STOR049

STOR050

STOR0501

STOR0502

STOR0503

STOR0504

STOR0505

STOR0506

STOR0507

STOR0508