- Notes, cautions, and warnings
- Dell PowerEdge FC630 overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- Viewing System BIOS
- System BIOS Settings details
- Boot Settings
- Network Settings
- System Security
- System Information
- Memory Settings
- Processor Settings
- SATA Settings
- Integrated Devices
- Serial Communication
- System Profile Settings
- Miscellaneous Settings
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing sled components
- Safety instructions
- Recommended tools
- Sled
- Inside the sled
- Cooling shroud
- Processor blank and DIMM blank
- System memory
- PCIe mezzanine card
- Internal dual SD module (optional)
- rSPI card (optional)
- SD vFlash card
- Network Daughter Card
- Processors
- Hard drives or SSDs
- Hard drive or SSD bay numbering
- Hard drive or SSD installation guidelines
- Removing a hard drive or SSD
- Installing a hard drive or SSD
- Removing a hard drive or SSD blank
- Installing a hard drive or SSD blank
- Shutdown procedure for servicing a hard drive or SSD
- Configuring the boot drive
- Removing a 2.5-inch hard drive or SSD from a 2.5-inch hard drive or SSD carrier
- Installing a 2.5-inch hard drive or SSD in a 2.5-inch hard drive or SSD carrier
- Removing a 1.8-inch SSD from a 1.8-inch SSD carrier
- Installing a 1.8-inch SSD in a 1.8-inch SSD carrier
- Removing the hard drive or SSD cage
- Installing the hard drive or SSD cage
- Hard drive backplane
- PERC H730P slim card
- Storage controller card
- NVRAM backup battery
- System board
- Trusted Platform Module
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Getting help
Bienvenue
Bienvenue dans l’univers Dell
Mon compte
- Passer des commandes rapidement et facilement
- Afficher les commandes et suivre l’état de votre expédition
- Profitez de récompenses et de remises réservées aux membres
- Créez et accédez à une liste de vos produits
- Gérer vos sites, vos produits et vos contacts au niveau des produits Dell EMC à l’aide de la rubrique Gestion des informations de l’entreprise.
Dell PowerEdge FC630 Owner's Manual
Removing the sled
CAUTION: Many
repairs may only be done by a certified service technician. You should
only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service
and support team. Damage due to servicing that is not authorized by
Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
Follow the safety guidelines listed in safety instructions section.
Turn off the sled using the operating system commands or the CMC, and ensure that the sled's front panel indicator is off.
- Press the release button on the sled handle to the unlock position.
- Rotate the sled handle away from the sled to disengage the sled from the midplane connectors.
- Slide the sled out of the enclosure.CAUTION: To protect the I/O connector pins, install the I/O connector cover every time a sled is removed from the enclosure.
- Install the I/O connector cover over the I/O
connector.CAUTION: If you are permanently removing the sled, install a sled blank. Operating the system for extended periods of time without a sled blank installed can cause the enclosure to overheat.
Figure 1. Removing the I/O connector cover 
- I/O connector cover
Figure 2. Removing the sled 
- FX2/FX2s enclosure
- sled
- sled handle
- release button
Veuillez attribuer une note (1 à 5 étoiles).
Veuillez attribuer une note (1 à 5 étoiles).
Veuillez attribuer une note (1 à 5 étoiles).
Veuillez indiquer si l’article a été utile ou non.
Les commentaires ne doivent pas contenir les caractères spéciaux : <>()\