跳至主要內容
登出

歡迎來到 Dell

我的帳戶
  • 簡單快速地下訂單
  • 檢視訂單及追蹤商品運送狀態
  • 建立並存取您的產品清單
  • 使用「公司管理」來管理您的 Dell EMC 網站、產品和產品層級連絡人。
登入 建立帳戶 Premier 登入 合作夥伴計畫登入
與我們連絡

您的 Dell.com 購物車

Dell PowerEdge R760 Installation and Service Manual

PDF

Cable routings

Figure 1. Configuration 0: 12 x 3.5-inch SAS/SATA with APERC11/12 in Riser 2
This image shows cable routing 12 x 3.5-inch SAS/SATA with APERC in Riser 2
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 1. 12 x 3.5-inch SAS/SATA with APERC11/12 in Riser 2 This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 CTRL_SRC_SA1_PA1 (adapter PERC controller connector) BP_DST_SA1 (backplane signal connector)
3 CTRL_SRC_SB1_PB1 (adapter PERC controller connector) BP_DST_SB1 (backplane signal connector)
Figure 2. Configuration 1: 12 x 3.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA with APERC11/12 in Riser 2
This image shows cable routing of 12 x 3.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA with APERC in Riser 2
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 2. 12 x 3.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA with APERC11/12 in Riser 2This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 CTRL_SRC_SB1_PB1 (adapter PERC controller connector) and BP_DST_SB1 (backplane signal connector) BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
3 CTRL_SRC_SA1_PA1 (adapter PERC controller connector) BP_DST_SA1 (backplane signal connector)
4 SIG_PWR_0 (system board power connector) BP_PWR_1 (rear backplane power connector)
Figure 3. Configuration 2: 12 x 3.5-inch SAS/SATA + 2 x 2.5-inch NVMe with APERC11/12 in Riser 2
This image shows cable routing of 12 x 3.5-inch SAS/SATA + 2 x 2.5-inch NVMe with APERC in Riser 2
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 3. 12 x 3.5-inch SAS/SATA + 2 x 2.5-inch NVMe with APERC11/12 in Riser 2This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 CTRL_SRC_SB1_PB1 (adapter PERC controller connector) BP_DST_SB1 (backplane signal connector)
3 CTRL_SRC_SA1_PA1 (adapter PERC controller connector) BP_DST_SA1 (backplane signal connector)
4 SIG_PWR_0 (system board power connector) BP_PWR_1 (rear backplane power connector)
5 SL11_CPU1_PB7 (signal connector on system board) BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
Figure 4. Configuration 3: 12 x 3.5-inch SAS/SATA + 4 x 2.5-inch SAS/SATA with APERC11/12 in Riser 2
This image shows cable routing of 12 x 3.5-inch SAS/SATA + 4 x 2.5-inch SAS/SATA with APERC in Riser 2
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 4. 12 x 3.5-inch SAS/SATA + 4 x 2.5-inch SAS/SATA with APERC11/12 in Riser 2 This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 CTRL_SRC_SB1_PB1 (adapter PERC controller connector) and BP_DST_SB1 (backplane signal connector) BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
3 CTRL_SRC_SA1_PA1 (adapter PERC controller connector) BP_DST_SA1 (backplane signal connector)
4 SIG_PWR_0 (system board power connector) BP_PWR_1 (rear backplane power connector)
Figure 5. Configuration 4: 12 x 3.5-inch SAS/SATA + 4 x 2.5-inch NVMe with APERC11/12 in Riser 2
This image shows cable routing of 12 x 3.5-inch SAS/SATA + 4 x 2.5-inch NVMe with APERC in Riser 2
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 5. 12 x 3.5-inch SAS/SATA + 4 x 2.5-inch NVMe with APERC11/12 in Riser 2This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SIG_PWR_0 (system board power connector) BP_PWR_1 (rear backplane power connector)
3 SL4_CPU1_PA2 (signal connector on system board) BP_DST_PA1 (rear backplane signal connector) and BP_DST_PB1 (rear backplane signal connector)
4 SL11_CPU1_PB7 (signal connector on system board) BP_DST_PA2 (rear backplane signal connector) and BP_DST_PB2 (rear backplane signal connector)
5 CTRL_SRC_SB1_PB1 (adapter PERC controller connector) BP_DST_SB1 (backplane signal connector)
6 CTRL_SRC_SA1_PA1 (adapter PERC controller connector) BP_DST_SA1 (backplane signal connector)
Figure 6. Configuration 5: 8 x 2.5-inch NVMe
This image shows cable routing of 8 x 2.5-inch NVMe
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 6. 8 x 2.5-inch NVMe This table shows connector information.
Order From To
1 SL1_CPU2_PA1 (signal connector on system board) BP_DST_PA1 (backplane signal connector)
2 SL2_CPU2_PB1 (signal connector on system board) BP_DST_PB1 (backplane signal connector)
3 SL3_CPU1_PA2 (signal connector on system board) and SL4_CPU1_PB2 (signal connector on system board) BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
4 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
Figure 7. Configuration 6: 8 x 2.5-inch NVMe RAID with fPERC (H755N)
This image shows cable routing of 8 x 2.5-inch NVMe RAID with fPERC (H755N)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 7. 8 x 2.5-inch NVMe RAID with fPERC (H755N)This table shows connector information.
Order From To
1 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
2 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
3 CTRL_SRC_PB1 (fPERC controller connector) BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
4 CTRL_SRC_PA1 (fPERC controller connector) BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
NOTE:An 8 x 2.5-inch NVMe backplane with fPERC H755 should be assembled outside and inserted into the system, along with all necessary cables.
Figure 8. Configuration 7: 8 x 2.5-inch NVMe RAID with fPERC (H965i)
This image shows cable routing of 8 x 2.5-inch NVMe RAID with fPERC (H965i)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 8. 8 x 2.5-inch NVMe RAID with fPERC (H965i)This table shows connector information.
Order From To
1 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
4 CTRL_SRC_PB1 (fPERC controller connector) BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
5 CTRL_SRC_PA1 (fPERC controller connector) BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
NOTE:An 8 x 2.5-inch NVMe backplane with fPERC H965i should be assembled outside and inserted into the system, along with all necessary cables.
Figure 9. Configuration 8: 8 x 2.5-inch Universal (SAS/SATA/NVMe) with fPERC (HBA355i, H355, H755)
This image shows cable routing of 8 x 2.5-inch Universal with fPERC (HBA355i, H355, H7555)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 9. 8 x 2.5-inch Universal (SAS/SATA/NVMe) with fPERC (HBA355i, H355, H755)This table shows connector information.
Order From To
1 SL5_CPU2_PB3 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
2 SL3_CPU1_PA2 (signal connector on system board) and SL4_CPU1_PB2 (signal connector on system board) BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
3 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
4 SL2_CPU2_PB1 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
5 SL1_CPU2_PA1 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
Figure 10. Configuration 9: 16 x 2.5-inch NVMe RAID with fPERC (H755N)
This image shows cable routing of 16 x 2.5-inch NVMe RAID with fPERC (H755N)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 10. 16 x 2.5-inch NVMe RAID with fPERC (H755N)This table shows connector information.
Order From To
1 SL1_CPU2_PA1 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
2 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
3 CTRL_SRC_PB1 (fPERC controller connector) BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
4 CTRL_SRC_PA1 (fPERC controller connector) BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
5 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
6 SIG_PWR_2 (system board power connector) BP_PWR_1 (backplane power connector)
7 CTRL_SRC_PB1 (fPERC controller connector) BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
8 CTRL_SRC_PA1 (fPERC controller connector) BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
NOTE:An 8 x 2.5-inch NVMe backplanes with fPERC H755 should be assembled outside and inserted into the system, along with all necessary cables.
Figure 11. Configuration 10: 16 x 2.5-inch NVMe
This image shows cable routing of 16 x 2.5-inch NVMe
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 11. 16 x 2.5-inch NVMe This table shows connector information.
Order From To
1 SL2_CPU2_PA1 (signal connector on system board) BP_DST_PA1 (backplane signal connector)
2 SL1_CPU2_PB1 (signal connector on system board) BP_DST_PB1 (backplane signal connector)
3 SL5_CPU2_PB3 (signal connector on system board) BP_DST_PA2 (backplane signal connector)
4 SL6_CPU2_PA3 (signal connector on system board) BP_DST_PB2 (backplane signal connector)
5 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
6 SL3_CPU1_PA2 (signal connector on system board) BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
7 SL4_CPU1_PB2 (signal connector on system board) BP_DST_PB1 (backplane signal connector)
8 SL7_CPU1_PB4 (signal connector on system board) BP_DST_PA2 (backplane signal connector)
9 SIG_PWR_2 (system board power connector) BP_PWR_1 (backplane power connector)
10 SL8_CPU1_PA4 (signal connector on system board) BP_DST_PB2 (backplane signal connector)
Figure 12. Configuration 11: 16 x 2.5-inch NVMe RAID with fPERC (H965i)
This image shows cable routing of 16 x 2.5-inch NVMe RAID with fPERC (H965i)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 12. 16 x 2.5-inch NVMe RAID with fPERC (H965i)This table shows connector information.
Order From To
1 SL1_CPU2_PB1 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
2 SL2_CPU2_PA1 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
3 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
4 CTRL_SRC_PB1 (fPERC controller connector) BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
5 CTRL_SRC_PA1 (fPERC controller connector) BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
6 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
7 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
8 SIG_PWR_2 (system board power connector) BP_PWR_1 (backplane power connector)
9 CTRL_SRC_PB1 (fPERC controller connector) BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
10 CTRL_SRC_PA1 (fPERC controller connector) BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
NOTE:An 8 x 2.5-inch NVMe backplanes with fPERC H965i should be assembled outside and inserted into the system, along with all necessary cables.
Figure 13. Configuration 12: 16 x 2.5-inch SAS/SATA with fPERC (HBA355i, H355, H755)
This image shows cable routing of 16 x 2.5-inch SAS/SATA with fPERC (HBA355i, H355, H755)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 13. 16 x 2.5-inch SAS/SATA with fPERC (HBA355i, H355, H755)This table shows connector information.
Order From To
1 SL3_CPU1_PA2 (signal connector on system board) CTRL_SRC_PA1 (fPERC controller connector)
2 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
3 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SA1 (backplane signal connector)
4 SIG_PWR_2 (system board power connector) BP_PWR_1 (backplane power connector)
Figure 14. Configuration 13: 16 x 2.5-inch SAS/SATA with fPERC (H965i)
This image shows cable routing of 16 x 2.5-inch SAS/SATA with fPERC (H965i)
Table 14. 16 x 2.5-inch SAS/SATA with fPERC (H965i)This table shows connector information.
Order From To
1 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
2 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
3 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
4 CTRL_SRC_SA1 (fPERC controller connector) BP_DST_SA1 (backplane signal connector)
5 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SA1 (backplane signal connector)
6 SIG_PWR_2 (system board power connector) BP_PWR_1 (backplane power connector)
Figure 15. Configuration 14: 16 x 2.5-inch SAS/SATA + 8 x 2.5-inch NVMe with fPERC (HBA355i, H355, H755)
This image shows cable routing of 16 x 2.5-inch SAS/SATA + 8 x 2.5-inch NVMe with fPERC (HBA355i, H355, H755)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 15. 16 x 2.5-inch SAS/SATA + 8 x 2.5-inch NVMe with fPERC (HBA355i, H355, H755)This table shows connector information.
Order From To
1 SL1_CPU2_PB1 (signal connector on system board) and SL2_CPU2_PA1 (signal connector on system board) BP_DST_PB1 (backplane signal connector) and BP_DST_PA1 (backplane signal connector)
2 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
3 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
4 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SA1 (backplane signal connector)
5 SIG_PWR_2 (system board power connector) BP_PWR_1 (backplane power connector)
6 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PA2 (fPERC input connector)
7 SL7_CPU1_PB4 (signal connector on system board) CTRL_DST_PB2 (fPERC input connector)
8 SIG_PWR_0 (system board power connector) BP_PWR_1 (backplane power connector)
Figure 16. Configuration 15: 16 x 2.5-inch SAS/SATA + 8 x 2.5-inch NVMe with fPERC (H965i)
This image shows cable routing of 16 x 2.5-inch SAS/SATA + 8 x 2.5-inch NVMe with fPERC (H965i)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 16. 16 x 2.5-inch SAS/SATA + 8 x 2.5-inch NVMe with fPERC (H965i)This table shows connector information.
Order From To
1 SL1_CPU2_PB1 (signal connector on system board) and SL2_CPU2_PA1 (signal connector on system board) BP_DST_PB1 (backplane signal connector) and BP_DST_PA1 (backplane signal connector)
2 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
3 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
4 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
5 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SA1 (backplane signal connector)
6 CTRL_SRC_SA1 (fPERC controller connector) BP_DST_SA1 (backplane signal connector)
7 SIG_PWR_2 (system board power connector) BP_PWR_1 (backplane power connector)
8 SL7_CPU1_PB4 (signal connector on system board) BP_DST_PA2 (backplane signal connector)
9 SIG_PWR_0 (system board power connector) BP_PWR_1 (backplane power connector)
10 SL8_CPU1_PA4 (signal connector on system board) BP_DST_BA2 (backplane signal connector)
Figure 17. Configuration 16: 16 x 2.5-inch SAS/SATA + 8 x 2.5-inch NVMe with fPERC (HBA355i, H355, H755)
This image shows cable routing of 16 x 2.5-inch SAS/SATA + 8 x 2.5-inch NVMe with fPERC (HBA355i, H355, H755)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 17. 16 x 2.5-inch SAS/SATA + 8 x 2.5-inch NVMe with fPERC (HBA355i, H355, H755)This table shows connector information.
Order From To
1 SL1_CPU2_PA1 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
2 SL5_CPU2_PB3 (signal connector on system board) BP_DST_PA1 (backplane signal connector)
3 SL6_CPU2_PA3 (signal connector on system board) BP_DST_PB1 (backplane signal connector)
4 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
5 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SA1 (backplane signal connector)
6 SL3_CPU1_PA2 (signal connector on system board) BP_DST_PA2 (backplane signal connector)
7 SL4_CPU1_PB2 (signal connector on system board) BP_DST_PB2 (backplane signal connector)
8 SIG_PWR_2 (system board power connector) BP_PWR_1 (backplane power connector)
9 SIG_PWR_0 (system board power connector) BP_PWR_1 (backplane power connector)
Figure 18. Configuration 17: 16 x 2.5-inch SAS/SATA + 8 x 2.5-inch NVMe with fPERC (H965i)
This image shows cable routing of 16 x 2.5-inch SAS/SATA + 8 x 2.5-inch NVMe with fPERC (H965i)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 18. 16 x 2.5-inch SAS/SATA + 8 x 2.5-inch NVMe with fPERC (H965i)This table shows connector information.
Order From To
1 SL1_CPU2_PA1 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
2 SL2_CPU2_PB1 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
3 SL5_CPU2_PB3 (signal connector on system board) BP_DST_PA1 (backplane signal connector)
4 SL6_CPU2_PA3 (signal connector on system board) BP_DST_PB1 (backplane signal connector)
5 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
6 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SA1 (backplane signal connector)
7 CTRL_SRC_SA1 (fPERC controller connector) BP_DST_SA1 (backplane signal connector)
8 SL3_CPU1_PA2 (signal connector on system board) BP_DST_PA2 (backplane signal connector)
9 SL4_CPU1_PB2 (signal connector on system board) BP_DST_PB2 (backplane signal connector)
10 SIG_PWR_2 (system board power connector) BP_PWR_1 (backplane power connector)
11 SIG_PWR_0 (system board power connector) BP_PWR_1 (backplane power connector)
Figure 19. Configuration 18: 24 x 2.5-inch SAS/SATA with 8 universal (SAS/SATA/NVMe) slots and fPERC (H965i)
This image shows cable routing of 24 x 2.5-inch SAS/SATA with 8 universal slot and fPERC (H965i)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 19. 24 x 2.5-inch SAS/SATA with 8 universal (SAS/SATA/NVMe) slots and fPERC (H965i)This table shows connector information.
Order From To
1 SL1_CPU2_PA1 (signal connector on system board) and SL2_CPU2_PB1 (signal connector on system board) BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
2 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
3 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
4 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
5 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
6 CTRL_SRC_SA1 (fPERC controller connector) BP_DST_SA1 (backplane expander signal connector)
7 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
8 SL7_CPU1_PB4 (signal connector on system board) BP_DST_PA2 (backplane signal connector)
9 SL8_CPU1_PA4 (signal connector on system board) BP_DST_PB2 (backplane signal connector)
Figure 20. Configuration 19: 24 x 2.5-inch SAS/SATA with fPERC (H965i)
This image shows cable routing of 24 x 2.5-inch SAS/SATA with fPERC (H965i)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 20. 24 x 2.5-inch SAS/SATA with fPERC (H965i)This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
4 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
5 CTRL_SRC_SA1 (fPERC controller connector) BP_DST_SA1 (backplane expander signal connector)
6 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
Figure 21. Configuration 20: 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch NVMe with fPERC (H965i)
This image shows cable routing of 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch NVMe with fPERC (H965i)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 21. 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch NVMe with fPERC (H965i)This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
4 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
5 CTRL_SRC_SA1 (fPERC controller connector) BP_DST_SA1 (backplane expander signal connector)
6 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
7 SL11_CPU1_PB7 (signal connector on system board) BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
8 SIG_PWR_0 (system board power connector) BP_PWR_1 (rear backplane power connector)
Figure 22. Configuration 21: 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA with fPERC (H965i)
This image shows cable routing of 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA with fPERC (H965i)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 22. 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA with fPERC (H965i)This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
4 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
5 CTRL_SRC_SA1 (fPERC controller connector) BP_DST_SA1 (backplane expander signal connector)
6 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
7 BP_SRC_SA2 (backplane expander signal connector) BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
8 SIG_PWR_0 (system board power connector) BP_PWR_1 (rear backplane power connector)
Figure 23. Configuration 22: 24 x 2.5-inch SAS/SATA + 4 x 2.5-inch SAS/SATA with fPERC (H965i)
This image shows cable routing of 24 x 2.5-inch SAS/SATA + 4 x 2.5-inch SAS/SATA with fPERC (H965i)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 23. 24 x 2.5-inch SAS/SATA + 4 x 2.5-inch SAS/SATA with fPERC (H965i)This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
4 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
5 CTRL_SRC_SA1 (fPERC controller connector) BP_DST_SA1 (backplane expander signal connector)
6 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
7 BP_SRC_SA2 (backplane expander signal connector) BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
8 SIG_PWR_0 (system board power connector) BP_PWR_1 (rear backplane power connector)
Figure 24. Configuration 23: 24 x 2.5-inch SAS/SATA + 4 x 2.5-inch NVMe with fPERC (H965i)
This image shows cable routing of 24 x 2.5-inch SAS/SATA + 4 x 2.5-inch NVMe with fPERC (H965i)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 24. 24 x 2.5-inch SAS/SATA + 4 x 2.5-inch NVMe with fPERC (H965i)This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
4 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
5 CTRL_SRC_SA1 (fPERC controller connector) BP_DST_SA1 (backplane expander signal connector)
6 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
7 SL11_CPU1_PB7 (signal connector on system board) BP_DST_PA2 (rear backplane signal connector) and BP_DST_PB2 (rear backplane signal connector)
8 SL8_CPU1_PA4 (signal connector on system board) BP_DST_PA1 (rear backplane signal connector) and BP_DST_PB1 (rear backplane signal connector)
9 SIG_PWR_0 (system board power connector) BP_PWR_1 (rear backplane power connector)
Figure 25. Configuration 24: 24 x 2.5-inch SAS/SATA dual controller with fPERC (H965i) and APERC in Riser 2
This image shows cable routing of 24 x 2.5-inch SAS/SATA dual controller with fPERC (H965i) and APERC in Riser 2
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 25. 24 x 2.5-inch SAS/SATA dual controller with fPERC (H965i) and APERC in Riser 2This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
4 CTRL_SRC_SA1 (fPERC controller connector) BP_DST_SA1 (backplane expander signal connector)
5 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
6 CTRL_SRC_SA1_PA1 (adapter PERC controller connector) BP_DST_SB1 (backplane expander signal connector)
Figure 26. Configuration 25: 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA dual controller with fPERC (H965i) and APERC in Riser 2
This image shows cable routing of 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA dual controller with fPERC (H965i) and APERC in Riser 1
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 26. 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA dual controller with fPERC (H965i) and APERC in Riser 2This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
4 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
5 CTRL_SRC_SA1 (fPERC controller connector) BP_DST_SA1 (backplane expander signal connector)
6 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
7 SIG_PWR_0 (system board power connector) BP_PWR_1 (rear backplane power connector)
8 CTRL_SRC_SA1_PA1 (adapter PERC controller connector) BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
Figure 27. Configuration 26: 24 x 2.5-inch SAS/SATA with 8 universal (SAS/SATA/NVMe) slot and fPERC (H965i)
This image shows cable routing of 24 x 2.5-inch SAS/SATA with 8 universal slot and fPERC (H965i)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 27. 24 x 2.5-inch SAS/SATA with 8 universal (SAS/SATA/NVMe) slot and fPERC (H965i)This table shows connector information.
Order From To
1 SL1_CPU2_PA1 (signal connector on system board) and SL2_CPU2_PB1 (signal connector on system board) BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
2 SL5_CPU2_PB3 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 SL6_CPU2_PA3 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
4 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
5 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
6 CTRL_SRC_SA1 (fPERC controller connector) BP_DST_SA1 (backplane expander signal connector)
7 SL3_CPU1_PA2 (signal connector on system board) BP_DST_PA2 (backplane signal connector)
8 SL4_CPU1_PB2 (signal connector on system board) BP_DST_PB2 (backplane signal connector)
9 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
Figure 28. Configuration 27: 24 x 2.5-inch SAS/SATA with 8 universal (SAS/SATA/NVMe) slot and fPERC (HBA355i, H355, H755)
This image shows cable routing of 24 x 2.5-inch SAS/SATA with 8 universal slot and fPERC (HBA355i, H355, H755)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 28. 24 x 2.5-inch SAS/SATA with eight universal slots (SAS/SATA/NVMe) and fPERC (HBA355i, H355, H755)This table shows connector information.
Order From To
1 SL1_CPU2_PA1 (signal connector on system board) and SL2_CPU2_PB1 (signal connector on system board) BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
2 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
3 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
4 SL4_CPU1_PB2 (signal connector on system board) BP_DST_PA2 (backplane signal connector)
5 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
6 CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
7 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
8 SL7_CPU1_PB4 (signal connector on system board) BP_DST_PB2 (backplane signal connector)
Figure 29. Configuration 28: 24 x 2.5-inch SAS/SATA with fPERC (HBA355i, H355, H755)
This image shows cable routing of 24 x 2.5-inch SAS/SATA with fPERC (HBA355i, H355, H755)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 29. 24 x 2.5-inch SAS/SATA with fPERC (HBA355i, H355, H755)This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
4 CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
5 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
Figure 30. Configuration 29: 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch NVMe with fPERC (HBA355i, H355, H755)
This image shows cable routing of 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch NVMe with fPERC (HBA355i, H355, H755)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 30. 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch NVMe with fPERC (HBA355i, H355, H755)This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
4 CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
5 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
6 SIG_PWR_0 (system board power connector) BP_PWR_1 (rear backplane power connector)
7 SL11_CPU1_PB7 (signal connector on system board) BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
Figure 31. Configuration 30: 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA with fPERC (HBA355i, H355, H755)
This image shows cable routing of 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA with fPERC (HBA355i, H355, H755)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 31. 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA with fPERC (HBA355i, H355, H755)This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
4 CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
5 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
6 SIG_PWR_0 (system board power connector) BP_PWR_1 (rear backplane power connector)
7 BP_SRC_SA2 (backplane expander signal connector) BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
Figure 32. Configuration 31: 24 x 2.5-inch SAS/SATA + 4 x 2.5-inch SAS/SATA with fPERC (HBA355i, H355, H755)
This image shows cable routing of 24 x 2.5-inch SAS/SATA + 4 x 2.5-inch SAS/SATA with fPERC (HBA355i, H355, H755)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 32. 24 x 2.5-inch SAS/SATA + 4 x 2.5-inch SAS/SATA with fPERC (HBA355i, H355, H755)This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
4 CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
5 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
6 SIG_PWR_0 (system board power connector) BP_PWR_1 (rear backplane power connector)
7 BP_SRC_SA2 (backplane expander signal connector) BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
Figure 33. Configuration 32: 24 x 2.5-inch SAS/SATA + 4 x 2.5-inch NVMe with fPERC (HBA355i, H355, H755)
This image shows cable routing of 24 x 2.5-inch SAS/SATA + 4 x 2.5-inch NVMe with fPERC (HBA355i, H355, H755)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 33. 24 x 2.5-inch SAS/SATA + 4 x 2.5-inch NVMe with fPERC (HBA355i, H355, H755)This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
4 CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
5 SL4_CPU1_PB2 (signal connector on system board) BP_DST_PA1 (rear backplane signal connector) and BP_DST_PB1 (rear backplane signal connector)
6 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
7 SIG_PWR_0 (system board power connector) BP_PWR_1 (rear backplane power connector)
8 SL11_CPU1_PB7 (signal connector on system board) BP_DST_PA2 (rear backplane signal connector) and BP_DST_PB2 (rear backplane signal connector)
Figure 34. Configuration 33: 24 x 2.5-inch SAS/SATA dual controller with fPERC (HBA355i, H355, H755) and APERC in Riser 2
This image shows cable routing of 24 x 2.5-inch SAS/SATA dual controller with fPERC (HBA355i, H355, H755) and APERC in Riser 2
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 34. 24 x 2.5-inch SAS/SATA dual controller with fPERC (HBA355i, H355, H755) and APERC in Riser 2This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
4 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
5 CTRL_SRC_SA1_PA1 (adapter PERC controller connector) BP_DST_SB1 (backplane expander signal connector)
Figure 35. Configuration 34: 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA dual controller with fPERC (HBA355i, H355, H755) and APERC in Riser 2
This image shows cable routing of 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA dual controller with fPERC (HBA355i, H355, H755) and APERC in Riser 2
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 35. 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA dual controller with fPERC (HBA355i, H355, H755) and APERC in Riser 2This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
4 CTRL_SRC_SA1 (fPERC controller connector) BP_DST_SA1 (backplane expander signal connector)
5 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
6 SIG_PWR_0 (system board power connector) BP_PWR_1 (rear backplane power connector)
7 CTRL_SRC_SA1_PA1 (adapter PERC controller connector) BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
Figure 36. Configuration 35: 24 x 2.5-inch SAS/SATA with 8 universal (SAS/SATA/NVMe) slots and fPERC (HBA355i, H355, H755)
This image shows cable routing of 24 x 2.5-inch SAS/SATA with 8 universal slot and fPERC (HBA355i, H355, H755)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 36. 24 x 2.5-inch SAS/SATA with 8 universal (SAS/SATA/NVMe) slots and fPERC (HBA355i, H355, H755)This table shows connector information.
Order From To
1 SL1_CPU2_PA1 (signal connector on system board) and SL2_CPU2_PB1 (signal connector on system board) BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
2 SL5_CPU2_PB3 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
4 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
5 CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
6 SL3_CPU1_PA2 (signal connector on system board) BP_DST_PA2 (backplane signal connector)
7 SL4_CPU1_PB2 (signal connector on system board) BP_DST_PB2 (backplane signal connector)
8 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
Figure 37. Configuration 36: 24 x 2.5-inch SAS/SATA with 4 universal (SAS/SATA/NVMe) slots + 4 x 2.5-inch SAS/SATA with fPERC (HBA355i)
This image shows cable routing of 24 x 2.5-inch SAS/SATA with 4 universal slot + 4 x 2.5-inch SAS/SATA with fPERC (HBA355i)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 37. 24 x 2.5-inch SAS/SATA with 4 universal (SAS/SATA/NVMe) slots+ 4 x 2.5-inch SAS/SATA with fPERC (HBA355i)This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
4 CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
5 SL4_CPU1_PB2 (signal connector on system board) BP_DST_PA2 (backplane signal connector)
6 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
7 SL7_CPU1_PB4 (signal connector on system board) BP_DST_PB2 (backplane signal connector)
8 SIG_PWR_0 (system board power connector) BP_PWR_1 (rear backplane power connector)
9 BP_SRC_SA2 (backplane expander signal connector) BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
Figure 38. Configuration 37: 16 x 2.5-inch (8 x SAS/SATA with fPERC (HBA355i, H355, H755) + 8 x NVMe RAID with fPERC (H755N))
This image shows cable routing of 16 x 2.5-inch (8 x SAS/SATA with fPERC (HBA355i, H355, H755) + 8 x NVMe RAID with fPERC (H755N))
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 38. 16 x 2.5-inch (8 x SAS/SATA with fPERC (HBA355i, H355, H755) + 8 x NVMe RAID with fPERC (H755N))This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
4 CTRL_SRC_PB1 (fPERC controller connector) BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
5 CTRL_SRC_PA1 (fPERC controller connector) BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
6 SL7_CPU1_PB4 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
NOTE:An 8 x 2.5-inch NVMe backplane with fPERC H755N should be assembled outside and inserted into the system, along with all necessary cables.
Figure 39. Configuration 38: 16 x 2.5-inch (8 x SAS/SATA with fPERC (HBA355i, H355, H755) + 8 x NVMe RAID with fPERC (H965i))
This image shows cable routing of 16 x 2.5-inch (8 x SAS/SATA with fPERC (HBA355i, H355, H755) + 8 x NVMe RAID with fPERC (H965i))
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 39. 16 x 2.5-inch (8 x SAS/SATA with fPERC (HBA355i, H355, H755) + 8 x NVMe RAID with fPERC (H965i))This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
4 CTRL_SRC_PB1 (fPERC controller connector) BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
5 CTRL_SRC_PA1 (fPERC controller connector) BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
6 SL7_CPU1_PB4 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
7 SL8_CPU1_PA4 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
NOTE:An 8 x 2.5-inch NVMe backplane with fPERC H965i should be assembled outside and inserted into the system, along with all necessary cables.
Figure 40. Configuration 39: 16 x 2.5-inch (8 x SAS/SATA with fPERC (H965i) + 8 x NVMe RAID with fPERC (H755N))
This image shows cable routing of 16 x 2.5-inch (8 x SAS/SATA with fPERC (H965i) + 8 x NVMe RAID with fPERC (H755N)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 40. 16 x 2.5-inch (8 x SAS/SATA with fPERC (H965i) + 8 x NVMe RAID with fPERC (H755N))This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
4 CTRL_SRC_PA1 (fPERC controller connector) BP_DST_SA1 (backplane signal connector)
5 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
6 CTRL_SRC_PB1 (fPERC controller connector) BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
7 CTRL_SRC_PA1 (fPERC controller connector) BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
8 SL7_CPU1_PB4 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
NOTE:An 8 x 2.5-inch NVMe backplane with fPERC H755N should be assembled outside and inserted into the system, along with all necessary cables.
Figure 41. Configuration 40: 16 x 2.5-inch (8 x SAS/SATA with fPERC (H965i) + 8 x NVMe RAID with fPERC (H965i))
This image shows cable routing of 16 x 2.5-inch (8 x SAS/SATA with fPERC (H965i) + 8 x NVMe RAID with fPERC (H965i))
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 41. 16 x 2.5-inch (8 x SAS/SATA with fPERC (H965i) + 8 x NVMe RAID with fPERC (H965i))This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
4 CTRL_SRC_PA1 (fPERC controller connector) BP_DST_SA1 (backplane signal connector)
5 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
6 CTRL_SRC_PB1 (fPERC controller connector) BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
7 CTRL_SRC_PA1 (fPERC controller connector) BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
8 SL7_CPU1_PB4 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
9 SL8_CPU1_PA4 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
NOTE:An 8 x 2.5-inch NVMe backplane with fPERC H965i should be assembled outside and inserted into the system, along with all necessary cables.
Figure 42. Configuration 41: 24 x 2.5-inch (NVMe Gen4) Passive
This image shows cable routing of 24 x 2.5-inch (NVMe Gen4) Passive
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 42. 24 x 2.5-inch (NVMe Gen4) PassiveThis table shows connector information.
Order From To
1 IO_RISER4(CPU2) (Riser 4 connector on system board) BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
2 SL1_CPU2_PA1 (signal connector on system board) BP_DST_PA2 (backplane signal connector)
3 SL2_CPU2_PB1 (signal connector on system board) BP_DST_PB2 (backplane signal connector)
4 SL5_CPU2_PB3 (signal connector on system board) BP_DST_PA3 (backplane signal connector)
5 SL6_CPU2_PA3 (signal connector on system board) BP_DST_PB3 (backplane signal connector)
6 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
7 SL3_CPU1_PA2 (signal connector on system board) BP_DST_PA4 (backplane signal connector)
8 SL4_CPU1_PB2 (signal connector on system board) BP_DST_PB4 (backplane signal connector)
9 SL7_CPU1_PB4 (signal connector on system board) BP_DST_PA5 (backplane signal connector)
10 SL8_CPU1_PA4 (signal connector on system board) BP_DST_PB5 (backplane signal connector)
11 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
12 IO_RISER1(CPU1) (Riser 1 connector on system board) BP_DST_PA6 (backplane signal connector) and BP_DST_PB6 (backplane signal connector)
Figure 43. Configuration 42: BOSS-N1 module in Riser 1
This image shows cable routing of BOSS-N1 module in Riser 1
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 43. BOSS-N1 module in Riser 1This table shows connector information.
Order From To
1 BOSS_PWR_MB (BOSS power connector on system board) BOSS_PWR (BOSS module power connector)
2 SL12_PCH_PA6 (signal connector on system board) BOSS (BOSS module signal connector)
NOTE:The BOSS-N1 power and signal cables are routed beneath Riser 1 and ensure not to damage the cables.
Figure 44. Configuration 43: BOSS-N1 module in 4 x 2.5-inch rear drive module
This image shows cable routing of BOSS-N1 module in 4 x 2.5-inch rear drive module
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 44. BOSS-N1 module in 4 x 2.5-inch rear drive moduleThis table shows connector information.
Order From To
1 BOSS_PWR_MB (BOSS power connector on system board) BOSS_PWR (BOSS module power connector)
2 SL12_PCH_PA6 (signal connector on system board) BOSS (BOSS module signal connector)
NOTE:The BOSS-N1 signal cable is routed beneath the rear drive module and ensures not to damage the cable.
Figure 45. Configuration 44: 16 x 2.5-inch (SAS/SATA) with one CPU and fPERC (H755)
This image shows cable routing of 16 x 2.5-inch (SAS/SATA) with one CPU and fPERC (H755)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 45. 16 x 2.5-inch (SAS/SATA) with one CPU and fPERC (H755)This table shows connector information.
Order From To
1 BP_DST_SA1 (backplane signal connector) CTRL_SRC_SB1 (fPERC controller connector)
2 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC controller connector)
3 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
4 SIG_PWR_2 (system board power connector) BP_PWR_1 (backplane power connector)
Figure 46. Configuration 45: 16 x EDSFF E3.S NVMe without fPERC
This image shows cable routing of 16 x EDSFF E3.S NVMe
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 46. 16 x EDSFF E3.S NVMe without fPERC This table shows connector information.
Order From To
1 SL1_CPU2_PA1 (signal connector on system board) BP_DST_PA1 (backplane signal connector)
2 SL2_CPU2_PB1 (signal connector on system board) BP_DST_PB1 (backplane signal connector)
3 SL5_CPU2_PB3 (signal connector on system board) BP_DST_PA2 (backplane signal connector)
4 SL6_CPU2_PA3 (signal connector on system board) BP_DST_PB2 (backplane signal connector)
5 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
6 SL3_CPU1_PA2 (signal connector on system board) BP_DST_PA1 (backplane signal connector)
7 SL4_CPU1_PB2 (signal connector on system board) BP_DST_PB1 (backplane signal connector)
8 SL7_CPU1_PB4 (signal connector on system board) BP_DST_PA2 (backplane signal connector)
9 SL8_CPU1_PA4 (signal connector on system board) BP_DST_PB2 (backplane signal connector)
10 SIG_PWR_2 (system board power connector) BP_PWR_1 (backplane power connector)
Figure 47. Configuration 46: 16 x EDSFF E3.S NVMe with dual fPERC (H965i)
This image shows cable routing of 16 x EDSFF E3.S NVMe with dual PERC H965i
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 47. 16 x EDSFF E3.S NVMe with dual fPERC (H965i)This table shows connector information.
Order From To
1 SL1_CPU2_PA1 (signal connector on system board) CTRL_DST_PA1 (fPERC controller connector)
2 SL2_CPU2_PB1 (signal connector on system board) CTRL_DST_PB1 (fPERC controller connector)
3 BP_PWR_CTRL (power controller connector on backplane) POWER (fPERC power controller connector)
4 BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector) CTRL_SRC_PA1 (fPERC controller connector)
5 BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector) CTRL_SRC_PB1 (fPERC controller connector)
6 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
7 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC controller connector)
8 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC controller connector)
9 BP_PWR_CTRL (power controller connector on backplane) POWER (fPERC power controller connector)
10 BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector) CTRL_SRC_PA1 (fPERC controller connector)
11 BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector) CTRL_SRC_PB1 (fPERC controller connector)
12 SIG_PWR_2 (system board power connector) BP_PWR_1 (backplane power connector)
Figure 48. Configuration 47: 24 x 2.5-inch (NVMe Gen5) switched
This image shows cable routing of 24 x 2.5-inch (NVMe Gen5) switched
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 48. 24 x 2.5-inch (NVMe Gen5) switched This table shows connector information.
Order From To
1 SL1_CPU2_PA1 (signal connector on system board) BP_DST_PA1 (backplane signal connector)
2 SL2_CPU2_PB1 (signal connector on system board) BP_DST_PB1 (backplane signal connector)
3 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
4 SL3_CPU1_PA2 (signal connector on system board) BP_DST_PA2 (backplane signal connector)
5 SL4_CPU1_PB2 (signal connector on system board) BP_DST_PB2 (backplane signal connector)
6 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
Figure 49. Configuration 48: 24 x 2.5-inch (NVMe Gen5) switched with dual fPERC (H965i)
This image shows cable routing of 24 x 2.5-inch (NVMe Gen5) switched with dual PERC(H965i)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 49. 24 x 2.5-inch (NVMe Gen5) switched with dual fPERC (H965i)This table shows connector information.
Order From To
1 BP_DST_PB1 (backplane signal connector) CTRL_SRC_PB1 (fPERC controller connector)
2 BP_DST_PA1 (backplane signal connector) CTRL_SRC_PA1 (fPERC controller connector)
3 SL1_CPU2_PA1 (signal connector on system board) CTRL_DST_PA1 (fPERC controller connector)
4 SL2_CPU2_PB1 (signal connector on system board) CTRL_DST_PB1 (fPERC controller connector)
5 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
6 BP_DST_PB2 (backplane signal connector) CTRL_SRC_PB1 (fPERC controller connector)
7 BP_DST_PA2 (backplane signal connector) CTRL_SRC_PA1 (fPERC controller connector)
8 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC controller connector)
9 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC controller connector)
10 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
Figure 50. Configuration 49: Dell DPU (Mellanox: 25 Gb, Pensando: 100 Gb or 25 Gb) without power cable
This image shows cable routing of Dell DPU without power cable
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 50. Dell DPU (Mellanox: 25 Gb, Pensando: 100 Gb or 25 Gb) without power cableThis table shows connector information.
Order From To
1 J_REAR_SERIAL1 ( UART connector on rear I/O card) UART (UART connector on MIC card)
2 CON1 (Connector 1 on MIC card) Connector on DPU card in riser 1
Figure 51. Configuration 50: 12 x 3.5-inch SAS/SATA + 4 x EDSFF E3.S with APERC11 in Riser 2
This image shows cable routing of 12 x 3.5-inch SAS/SATA + 4 EDSFF E3.S with APERC in Riser 2
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 51. 12 x 3.5-inch SAS/SATA + 4 x EDSFF E3.S with APERC11 in Riser 2This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 CTRL_SRC_SB1_PB1 (adapter PERC controller connector) BP_DST_SB1 (backplane signal connector)
3 CTRL_SRC_SA1_PA1 (adapter PERC controller connector) BP_DST_SA1 (backplane signal connector)
4 SIG_PWR_0 (system board power connector) Power connector on E3 rear module*
5 SL4_CPU1_PA2 (signal connector on system board) Rear backplane signal connector on E3 rear module*
6 SL11_CPU1_PB7 (signal connector on system board) Rear backplane signal connector on E3 rear module*
NOTE:*Disconnect cables from the system board side since the cables in the rear E3 module are preassembled.
Figure 52. Configuration 51: 24 x 2.5-inch SAS/SATA + 4 x EDSFF E3.S with fPERC (HBA355i, H355, H755)
This image shows cable routing of 24 x 2.5-inch SAS/SATA + 4 x EDSFF E3.S with fPERC (HBA355i, H355, H755)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 52. 24 x 2.5-inch SAS/SATA + 4 x EDSFF E3.S with fPERC (HBA355i, H355, H755)This table shows connector information.
Order From To
1 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
2 CTRL_SRC_SA1 (fPERC controller connector) BP_DST_SA1 (backplane expander signal connector)
3 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
4 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
5 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
6 SIG_PWR_0 (system board power connector) Power connector on E3 rear module*
7 SL4_CPU1_PA2 (signal connector on system board) Rear backplane signal connector on E3 rear module*
8 SL11_CPU1_PB7 (signal connector on system board) Rear backplane signal connector on E3 rear module*
NOTE:*Disconnect cables from the system board side since the cables in the rear E3 module are preassembled.
Figure 53. Configuration 52: 24 x 2.5-inch SAS/SATA + 4 x EDSFF E3.S with fPERC (H965i)
This image shows cable routing of 24 x 2.5-inch SAS/SATA + 4 x EDSFF E3.S with fPERC ( H965i)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 53. 24 x 2.5-inch SAS/SATA + 4 x EDSFF E3.S with fPERC (H965i)This table shows connector information.
Order From To
1 CTRL_SRC_SB1 (fPERC controller connector) BP_DST_SB1 (backplane expander signal connector)
2 CTRL_SRC_SA1 (fPERC controller connector) BP_DST_SA1 (backplane expander signal connector)
3 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
4 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
5 SIG_PWR_2 (system board power connector) BP_PWR_2 (backplane power connector)
6 SL4_CPU1_PA2 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
7 SIG_PWR_0 (system board power connector) Power connector on E3 rear module*
8 SL8_CPU1_PA4 (signal connector on system board) Rear backplane signal connector on E3 rear module*
9 SL11_CPU1_PB7 (signal connector on system board) Rear backplane signal connector on E3 rear module*
NOTE:*Disconnect cables from the system board side since the cables in the rear E3 module are preassembled.
Figure 54. Configuration 53: 8 x 2.5-inch Universal (SAS/SATA/NVMe) with fPERC (H965i)
This image shows cable routing of 8 x 2.5-inch Universal with fPERC (H965i)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 54. 8 x 2.5-inch Universal (SAS/SATA/NVMe) with fPERC (H965i)This table shows connector information.
Order From To
1 SL5_CPU2_PB3 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
2 SL6_CPU2_PA3 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
3 CTRL_SRC_SA1 (fPERC controller connector) BP_DST_SA1 (backplane expander signal connector)
4 SL3_CPU1_PA2 (signal connector on system board) and SL4_CPU1_PB2 (signal connector on system board) BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
5 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
6 SL2_CPU2_PB1 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
7 SL1_CPU2_PA1 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
Figure 55. Configuration 54: 16 x 2.5-inch (8 x SAS/SATA + 8 x NVMe RAID) dual controller with fPERC (H965i)
This image shows cable routing of 16 x 2.5-inch (8 x SAS/SATA + 8 x NVMe RAID) dual controller with fPERC (H965i)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 55. 16 x 2.5-inch (8 x SAS/SATA + 8 x NVMe RAID) dual controller with fPERC (H965i)This table shows connector information.
Order From To
1 SIG_PWR_1 (system board power connector) BP_PWR_1 (backplane power connector)
2 SL1_CPU2_PA1 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
3 SL2_CPU2_PB1 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
4 CTRL_SRC_PA1 (fPERC controller connector) BP_DST_SA1 (backplane signal connector)
5 SL3_CPU1_PA2 (signal connector on system board) CTRL_DST_PA1 (fPERC input connector)
6 SL4_CPU1_PB2 (signal connector on system board) CTRL_DST_PB1 (fPERC input connector)
7 CTRL_SRC_PB1 (fPERC controller connector) BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
8 CTRL_SRC_PA1 (fPERC controller connector) BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
9 SIG_PWR_2 (system board power connector) BP_PWR_1 (backplane power connector)
NOTE:An 8 x 2.5-inch NVMe backplane with fPERC H965i should be assembled outside and inserted into the system, along with all necessary cables.
Figure 56. Configuration 55: OCP cable
This image shows cable routing of OCP cable
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 56. OCP cableThis table shows connector information.
Order From To
1 SL11_CPU1_PB7 (signal connector on system board) SL13_CPU1_PB7 (signal connector on system board)

對此內容評分

準確
實用
易懂
這篇文章對您有用嗎？
0/3000 characters
  請給予評分 (1 到 5 顆星)。
  請給予評分 (1 到 5 顆星)。
  請給予評分 (1 到 5 顆星)。
  本文章是否有幫助？請選擇。
  評語中不得包含下列特殊字元：<>()\