Dell PowerEdge R760 Installation and Service Manual

PDF

Rear view of the system

this image shows rear view of the system — Figure 1. Rear view of the system

Table 1. Rear view of the systemItem 1 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 2 is the BOSS module. Item 3 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 4 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 5 is VGA port. Item 6 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 7 is PSU 2, supplies power to the components of the system. Item 8 is the USB 2.0 port, enables you to connect USB devices to the system. Item 9 is the USB 3.0 port, enables you to connect USB devices to the system. Item 10 is iDRAC Ethernet port. Item 11 is the System identification button, helps in identifying the system in a rack. Item 12 is the optional OCP NIC cad, integrated on the network daughter card (NDC) provides network connectivity. Item 13 is the NIC port, provides network connectivity. Item 14 is PSU 1, supplies power to the components of the system.
Item	Ports, panels, or slots	Icon	Description
1	PCIe expansion card riser 1 (slot 1 and slot 2)	N/A	The expansion card riser enables you to connect PCI Express expansion cards. For more information , see the Expansion card installation guidelines section.
2	BOSS module	N/A	BOSS module for internal system boot.
3	PCIe expansion card riser 2 (slot 3 and slot 6)	N/A	The expansion card riser enables you to connect PCI Express expansion cards. For more information , see the Expansion card installation guidelines section.
4	PCIe expansion card riser 3 (slot 4 and slot 5)	N/A	The expansion card riser enables you to connect PCI Express expansion cards. For more information , see the Expansion card installation guidelines section.
5	VGA port		Enables you to connect a display device to the system.
6	PCIe expansion card riser 4 (slot 7 and slot 8)	N/A	The expansion card riser enables you to connect PCI Express expansion cards. For more information , see the Expansion card installation guidelines section.
7	Power supply unit (PSU2)		PSU2 is the secondary PSU of the system.
8	USB 2.0 port		The USB port is 4-pin, 2.0-compliant. This port enables you to connect USB devices to the system.
9	USB 3.0 port		The USB port is 9-pin and 3.0-compliant. This port enables you to connect USB devices to the system.
10	Dedicated iDRAC9 Ethernet port		Enables you to remotely access iDRAC. For more information, see the Integrated Dell Remote Access Controller User's Guide at www.dell.com/poweredgemanuals.
11	System Identification (ID) button		The System Identification (ID) button is available on the front and back of the system. Press the button to identify a system in a rack by turning on the system ID button. You can also use the system ID button to reset iDRAC and to access BIOS using the step through mode. When pressed, the system ID LED in the back panel blinks until either the front or rear button is pressed again. Press the button to toggle between on or off mode. NOTE:If the server stops responding during POST, press and hold the System ID button for more than five seconds to enter the BIOS progress mode NOTE: To reset the iDRAC (if not disabled on the iDRAC setup page by pressing F2 during system boot), press and hold the System ID button for more than 15 seconds.
12	OCP NIC card (optional)	N/A	The OCP NIC card supports OCP 3.0. The NIC ports are integrated on the OCP card which is connected to the system board.
13	NIC ports (optional)		The NIC ports that are integrated on the LOM card provide network connectivity which is connected to the system board or Management Interface Card (MIC) to support Dell Data Processing Unit (DPU) card to be installed in the riser. NOTE:The system allows either LOM card or MIC card to be installed in the system.
14	Power supply unit (PSU1)		PSU1 is the primary PSU of the system.

this image shows rear view of the system with optional liquid cooling — Figure 2. Rear view of the system with optional liquid cooling

Table 2. Rear view of the system with optional liquid coolingItem 1 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 2 is the BOSS blank. Item 3 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 4 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 5 is the coolant tubes. Item 6 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 7 is PSU 2, supplies power to the components of the system. Item 8 is the USB 2.0 port, enables you to connect USB devices to the system. Item 9 is the USB 3.0 port, enables you to connect USB devices to the system. Item 10 is iDRAC Ethernet port Item 11 is the System identification button, helps in identifying the system in a rack. Item 12 is the optional OCP NIC cad, integrated on the network daughter card (NDC) provides network connectivity. Item 13 is the NIC port, provides network connectivity. Item 14 is PSU 1, supplies power to the components of the system.
Item	Ports, panels, or slots	Icon	Description
1	PCIe expansion card riser 1 (slot 1 and slot 2)	N/A	The expansion card riser enables you to connect PCI Express expansion cards. For more information , see the Expansion card installation guidelines section.
2	BOSS blank	N/A	Insert BOSS blank when BOSS module is not used.
3	PCIe expansion card riser 2 (slot 3 and slot 6)	N/A	The expansion card riser enables you to connect PCI Express expansion cards. For more information , see the Expansion card installation guidelines section.
4	PCIe expansion card riser 3 (slot 5)	N/A	The expansion card riser enables you to connect PCI Express expansion cards. For more information , see the Expansion card installation guidelines section.
5	Coolant tubes	N/A	Cold coolant flows into the system from one tube and hot coolant leaves the system from another tube.
6	PCIe expansion card riser 4 (slot 7)	N/A	The expansion card riser enables you to connect PCI Express expansion cards. For more information , see the Expansion card installation guidelines section.
7	Power supply unit (PSU2)		PSU2 is the secondary PSU of the system.
8	USB 2.0 port		The USB port is 4-pin, 2.0-compliant. This port enables you to connect USB devices to the system.
9	USB 3.0 port		The USB port is 9-pin and 3.0-compliant. This port enables you to connect USB devices to the system.
10	Dedicated iDRAC9 Ethernet port		Enables you to remotely access iDRAC. For more information, see the Integrated Dell Remote Access Controller User's Guide at www.dell.com/poweredgemanuals.
11	System Identification (ID) button		The System Identification (ID) button is available on the front and back of the system. Press the button to identify a system in a rack by turning on the system ID button. You can also use the system ID button to reset iDRAC and to access BIOS using the step through mode. When pressed, the system ID LED in the back panel blinks until either the front or rear button is pressed again. Press the button to toggle between on or off mode. NOTE:If the server stops responding during POST, press and hold the System ID button for more than five seconds to enter the BIOS progress mode NOTE: To reset the iDRAC (if not disabled on the iDRAC setup page by pressing F2 during system boot), press and hold the System ID button for more than 15 seconds.
12	OCP NIC card (optional)	N/A	The OCP NIC card supports OCP 3.0. The NIC ports are integrated on the OCP card which is connected to the system board.
13	NIC ports (optional)		The NIC ports that are integrated on the LOM card provide network connectivity which is connected to the system board or MIC to support Dell DPU card to be installed in the riser. NOTE:The system allows either LOM card or MIC card to be installed in the system.
14	Power supply unit (PSU1)		PSU1 is the primary PSU of the system.

this image shows Rear view of the system with 2 x 2.5-inch rear drive module — Figure 3. Rear view of the system with 2 x 2.5-inch rear drive module

Table 3. Rear view of the system with 2 x 2.5-inch rear drive moduleItem 1 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 2 is the BOSS module. Item 3 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 4 is the rear drive module, enables you to install rear drives. Item 5 is VGA port. Item 6 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 7 is PSU 2, supplies power to the components of the system. Item 8 is the USB 2.0 port, enables you to connect USB devices to the system. Item 9 is the USB 3.0 port, enables you to connect USB devices to the system. Item 10 is iDRAC Ethernet port. Item 11 is the System identification button, helps in identifying the system in a rack. Item 12 is the optional OCP NIC cad, integrated on the network daughter card (NDC) provides network connectivity. Item 13 is the NIC port, provides network connectivity. Item 14 is PSU 1, supplies power to the components of the system.
Item	Ports, panels, or slots	Icon	Description
1	PCIe expansion card riser 1 (slot 1 and slot 2)	N/A	The expansion card riser enables you to connect PCI Express expansion cards. For more information , see the Expansion card installation guidelines section.
2	BOSS module	N/A	BOSS module for internal system boot.
3	PCIe expansion card riser 2 (slot 3 and slot 6)	N/A	The expansion card riser enables you to connect PCI Express expansion cards. For more information , see the Expansion card installation guidelines section.
4	Rear drive module	N/A	Enables you to install rear drives that are supported on your system. NOTE:For drive slot numbers, see the Rear drive module section.
5	VGA port		Enables you to connect a display device to the system.
6	PCIe expansion card riser 4 (slot 7 and slot 8)	N/A	The expansion card riser enables you to connect PCI Express expansion cards. For more information , see the Expansion card installation guidelines section.
7	Power supply unit (PSU2)		PSU2 is the secondary PSU of the system.
8	USB 2.0 port		The USB port is 4-pin, 2.0-compliant. This port enables you to connect USB devices to the system.
9	USB 3.0 port		The USB port is 9-pin and 3.0-compliant. This port enables you to connect USB devices to the system.
10	Dedicated iDRAC9 Ethernet port		Enables you to remotely access iDRAC. For more information, see the Integrated Dell Remote Access Controller User's Guide at www.dell.com/poweredgemanuals.
11	System Identification (ID) button		The System Identification (ID) button is available on the front and back of the system. Press the button to identify a system in a rack by turning on the system ID button. You can also use the system ID button to reset iDRAC and to access BIOS using the step through mode. When pressed, the system ID LED in the back panel blinks until either the front or rear button is pressed again. Press the button to toggle between on or off mode. NOTE:If the server stops responding during POST, press and hold the System ID button for more than five seconds to enter the BIOS progress mode NOTE: To reset the iDRAC (if not disabled on the iDRAC setup page by pressing F2 during system boot), press and hold the System ID button for more than 15 seconds.
12	OCP NIC card (optional)	N/A	The OCP NIC card supports OCP 3.0. The NIC ports are integrated on the OCP card which is connected to the system board.
13	NIC ports (optional)		The NIC ports that are integrated on the LOM card provide network connectivity which is connected to the system board or MIC to support Dell DPU card to be installed in the riser. NOTE:The system allows either LOM card or MIC card to be installed in the system.
14	Power supply unit (PSU1)		PSU1 is the primary PSU of the system.

this image shows Rear view of the system with 4 x 2.5-inch rear drive module — Figure 4. Rear view of the system with 4 x 2.5-inch rear drive module

Table 4. Rear view of the system with 4 x 2.5-inch rear drive moduleItem 1 is the rear drive module, enables you to install rear drives .Item 2 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 3 is the BOSS module. Item 4 is VGA port. Item 5 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 6 is PSU 2, supplies power to the components of the system. Item 7 is the USB 2.0 port, enables you to connect USB devices to the system. Item 8 is the USB 3.0 port, enables you to connect USB devices to the system. Item 9 is the iDRAC Ethernet port. Item 10 is the System identification button, helps in identifying the system in a rack. Item 11 is the optional OCP NIC cad, integrated on the network daughter card (NDC) provides network connectivity. Item 12 is the NIC port, provides network connectivity. Item 13 is PSU 1, supplies power to the components of the system.
Item	Ports, panels, or slots	Icon	Description
1	Rear drive module	N/A	Enables you to install rear drives that are supported on your system. NOTE:For drive slot numbers, see the Rear drive module section.
2	PCIe expansion card riser 2 (slot 3 and slot 6)	N/A	The expansion card riser enables you to connect PCI Express expansion cards. For more information , see the Expansion card installation guidelines section.
3	BOSS module	N/A	BOSS module for internal system boot.
4	VGA port		Enables you to connect a display device to the system.
5	PCIe expansion card riser 4 (slot 7 and slot 8)	N/A	The expansion card riser enables you to connect PCI Express expansion cards. For more information , see the Expansion card installation guidelines section.
6	Power supply unit (PSU2)		PSU2 is the secondary PSU of the system.
7	USB 2.0 port		The USB port is 4-pin, 2.0-compliant. This port enables you to connect USB devices to the system.
8	USB 3.0 port		The USB port is 9-pin and 3.0-compliant. This port enables you to connect USB devices to the system.
9	Dedicated iDRAC9 Ethernet port		Enables you to remotely access iDRAC. For more information, see the Integrated Dell Remote Access Controller User's Guide at www.dell.com/poweredgemanuals.
10	System Identification (ID) button		The System Identification (ID) button is available on the front and back of the system. Press the button to identify a system in a rack by turning on the system ID button. You can also use the system ID button to reset iDRAC and to access BIOS using the step through mode. When pressed, the system ID LED in the back panel blinks until either the front or rear button is pressed again. Press the button to toggle between on or off mode. NOTE:If the server stops responding during POST, press and hold the System ID button for more than five seconds to enter the BIOS progress mode NOTE: To reset the iDRAC (if not disabled on the iDRAC setup page by pressing F2 during system boot), press and hold the System ID button for more than 15 seconds.
11	OCP NIC card (optional)	N/A	The OCP NIC card supports OCP 3.0. The NIC ports are integrated on the OCP card which is connected to the system board.
12	NIC ports (optional)		The NIC ports that are integrated on the LOM card provide network connectivity which is connected to the system board or MIC to support Dell DPU card to be installed in the riser. NOTE:The system allows either LOM card or MIC card to be installed in the system.
13	Power supply unit (PSU1)		PSU1 is the primary PSU of the system.

NOTE:For more information about ports, panels, and slots, see the Technical specification section.

this image shows Rear view of the system with 4 x EDSFF E3.S rear drive module — Figure 5. Rear view of the system with 4 x EDSFF E3.S rear drive module

Table 5. Rear view of the system with 4 x EDSFF E3.S rear drive moduleItem 1 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 2 is the BOSS module. Item 3 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 4 is the rear drive module, enables you to install rear drives. Item 5 is VGA port. Item 6 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 7 is PSU 2, supplies power to the components of the system. Item 8 is the USB 2.0 port, enables you to connect USB devices to the system. Item 9 is the USB 3.0 port, enables you to connect USB devices to the system. Item 10 is iDRAC Ethernet port. Item 11 is the System identification button, helps in identifying the system in a rack. Item 12 is the optional OCP NIC cad, integrated on the network daughter card (NDC) provides network connectivity. Item 13 is the NIC port, provides network connectivity. Item 14 is PSU 1, supplies power to the components of the system.
Item	Ports, panels, or slots	Icon	Description
1	PCIe expansion card riser 1 (slot 1 and slot 2)	N/A	The expansion card riser enables you to connect PCI Express expansion cards. For more information , see the Expansion card installation guidelines section.
2	BOSS module	N/A	BOSS module for internal system boot.
3	PCIe expansion card riser 2 (slot 3 and slot 6)	N/A	The expansion card riser enables you to connect PCI Express expansion cards. For more information , see the Expansion card installation guidelines section.
4	Rear drive module	N/A	Enables you to install rear drives that are supported on your system. NOTE:For drive slot numbers, see the Rear drive module section.
5	VGA port		Enables you to connect a display device to the system.
6	PCIe expansion card riser 4 (slot 7 and slot 8)	N/A	The expansion card riser enables you to connect PCI Express expansion cards. For more information , see the Expansion card installation guidelines section.
7	Power supply unit (PSU2)		PSU2 is the secondary PSU of the system.
8	USB 2.0 port		The USB port is 4-pin, 2.0-compliant. This port enables you to connect USB devices to the system.
9	USB 3.0 port		The USB port is 9-pin and 3.0-compliant. This port enables you to connect USB devices to the system.
10	Dedicated iDRAC9 Ethernet port		Enables you to remotely access iDRAC. For more information, see the Integrated Dell Remote Access Controller User's Guide at www.dell.com/poweredgemanuals.
11	System Identification (ID) button		The System Identification (ID) button is available on the front and back of the system. Press the button to identify a system in a rack by turning on the system ID button. You can also use the system ID button to reset iDRAC and to access BIOS using the step through mode. When pressed, the system ID LED in the back panel blinks until either the front or rear button is pressed again. Press the button to toggle between on or off mode. NOTE:If the server stops responding during POST, press and hold the System ID button for more than five seconds to enter the BIOS progress mode NOTE: To reset the iDRAC (if not disabled on the iDRAC setup page by pressing F2 during system boot), press and hold the System ID button for more than 15 seconds.
12	OCP NIC card (optional)	N/A	The OCP NIC card supports OCP 3.0. The NIC ports are integrated on the OCP card which is connected to the system board.
13	NIC ports (optional)		The NIC ports that are integrated on the LOM card provide network connectivity which is connected to the system board or MIC to support Dell DPU card to be installed in the riser. NOTE:The system allows either LOM card or MIC card to be installed in the system.
14	Power supply unit (PSU1)		PSU1 is the primary PSU of the system.