- Notes, cautions, and warnings
- About this document
- System overview
- Technical specifications
- Chassis dimensions
- System weight
- Processor specifications
- PSU specifications
- Supported operating systems
- Cooling fan specifications
- System battery specifications
- Expansion card riser specifications
- Memory specifications
- Storage controller specifications
- Drives
- Ports and connectors specifications
- Video specifications
- Environmental specifications
- Initial system setup and configuration
- Pre-operating system management applications
- System Setup
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Minimum to POST and system management configuration validation
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- Optional front bezel
- System cover
- Drive backplane cover
- Air shrouds
- Removing the air shroud
- Installing the air shroud
- Removing the GPU air shroud top cover
- Installing the GPU air shroud top cover
- Removing the GPU air shroud filler
- Installing the GPU air shroud filler
- Removing the GPU air shroud
- Installing the GPU air shroud
- Removing the 2 x 2.5-inch rear drive module air shroud
- Installing the 2 x 2.5-inch rear drive module air shroud
- Removing the 4 x 2.5-inch rear drive module air shroud
- Installing the 4 x 2.5-inch rear drive module air shroud
- Removing the EDSFF E3.S rear drive module air shroud
- Installing the EDSFF E3.S rear drive module air shroud
- Cooling fans
- Removing the cooling fan cage assembly
- Installing the cooling fan cage assembly
- Removing a cooling fan
- Installing a cooling fan
- Removing a 2 x 2.5-inch rear drive module cooling fan
- Installing a 2 x 2.5-inch rear drive module cooling fan
- Removing a 4 x 2.5-inch rear drive module cooling fan
- Installing a 4 x 2.5-inch rear drive module cooling fan
- Removing the EDSFF E3.S rear drive module cooling fan
- Installing the EDSFF E3.S rear drive module cooling fan
- Drives
- Removing a drive blank
- Installing a drive blank
- Removing a drive carrier
- Installing the drive carrier
- Removing the drive from the drive carrier
- Installing the drive into the drive carrier
- Removing an EDSFF E3.S drive blank
- Installing an EDSFF E3.S drive blank
- Removing an EDSFF E3.S drive carrier
- Installing an EDSFF E3.S drive carrier
- Removing an EDSFF E3.S drive from the drive carrier
- Installing an EDSFF E3.S drive into the drive carrier
- Rear drive module
- Drive backplane
- Side wall brackets
- Cable routings
- PERC module
- EDSFF E3.S backplane module
- System memory
- Processor and heat sink module
- Expansion cards and expansion card risers
- Expansion card installation guidelines
- Removing the expansion card risers
- Installing the expansion card risers
- Removing expansion card from the expansion card riser
- Installing an expansion card into the expansion card riser
- Removing the full length expansion card risers
- Installing the full length expansion card risers
- Removing a GPU
- Installing a GPU
- Removing R1 and R4 paddle cards
- Installing R1 and R4 paddle cards
- Optional serial COM port
- Optional VGA port for Direct Liquid Cooling module
- Optional BOSS-N1 module
- System battery
- Optional internal USB card
- Intrusion switch
- Optional OCP NIC card
- Power supply unit
- Trusted Platform Module
- System board
- LOM card, MIC card and rear I/O board
- Control panel
- Upgrade Kits
- Jumpers and connectors
- System diagnostics and indicator codes
- Getting help
- Documentation resources
Dell PowerEdge R760 Installation and Service Manual
Network Settings
To view the
Network Settings screen, power on the system, press F2, and click
.
NOTE:Network Settings are not supported in BIOS boot mode.
| Option | Description |
|---|---|
| UEFI PXE Settings | Enables you to control the configuration of the UEFI PXE device. |
| Number of PXE Devices | This field specifies the number of PXE devices. This option is set to 4 by default. |
| PXE Device n (n = 1 to 4) | Enables or disables the device. When enabled, a UEFI PXE boot option is created for the device. |
| PXE Device n Settings(n = 1 to 4) | Enables you to control the configuration of the PXE device. |
| UEFI HTTP Settings | Enables you to control the configuration of the UEFI HTTP device. |
| HTTP Device n (n = 1 to 4) | Enables or disables the device. When enabled, a UEFI HTTP boot option is created for the device. |
| HTTP Device n Settings (n = 1 to 4) | Enables you to control the configuration of the HTTP device. |
| UEFI iSCSI Settings | Enables you to control the configuration of the iSCSI device. |
| iSCSI Initiator Name | Specifies the name of the iSCSI initiator in IQN format. |
| iSCSI Device1 | Enables or disables the iSCSI device. When disabled, a UEFI boot option is created for the iSCSI device automatically. This is set to Disabled by default. |
| iSCSI Device1 Settings | Enables you to control the configuration of the iSCSI device. |
| UEFI NVMe-oF Settings | Enables you to control the configuration of the NVMe-oF devices. |
| NVMe-oF | Enables or disables the NVMe-oF feature. When enabled, it allows to configure the host and target parameters needed for fabric connection. This is set to Disabled by default. |
| NVMe-oF Host NQN | This field specifies the name of the NVMe-oF host NQN. Allowed input is in the following format: nqn.yyyy-mm.<Reserved Domain Name>:<Unique String>. Leave it empty to use system generated value with following format: nqn.1988-11.com.dell:<Model name>.<Model number>.<Service Tag>. |
| NVMe-oF Host Id | This field specifies a 16 bytes value of the NVMe-oF host identifier that uniquely identifies this host with the controller in the NVM subsystem. Allowed input is a hexadecimal-encoded string in this format: 00112233-4455-6677-8899-aabbccddeeff. Leave it empty to use system generated value. A value of all FF is not allowed. |
| Host Security Key Path | This field specifies the Host security key path. |
| NVMe-oF SubSystem Settings | This field controls the parameters for the NVMe-oF subsystem n connections. |
| Option | Description |
|---|---|
| Interface | Specifies NIC interface used for the PXE device. |
| Protocol | Specifies Protocol used for PXE device. This option is set to IPv4 or IPv6. This option is set to IPv4 by default. |
| Vlan | Enables Vlan for PXE device. This option is set to Enabled or Disabled. This option is set to Disabled by default. |
| Vlan ID | Shows the Vlan ID for the PXE device |
| Vlan Priority | Shows the Vlan Priority for the PXE device. |
| Option | Description |
|---|---|
| Interface | Specifies NIC interface used for the HTTP device. |
| Protocol | Specifies Protocol used for HTTP device. This option is set to IPv4 or IPv6. This option is set to IPv4 by default. |
| Vlan | Enables Vlan for HTTP device. This option is set to Enable or Disable. This option is set to Disable by default. |
| Vlan ID | Shows the Vlan ID for the HTTP device |
| Vlan Priority | Shows the Vlan Priority for the HTTP device. |
| DHCP | Enables or disables DHCP for this HTTP device. This option is set to Enabled by default. |
| IP Address | Specifies IP address for the HTTP device. |
| Subnet Mask | Specifies subnet mask for the HTTP device. |
| Autoconfiguration | Enables or disables the IPv6Autoconfiguration for the HTTP Device. When set to Enabled, IPv6 Address and Gateway are retrieved from Autoconfiguration mechanism. |
| Prefix Length | IPv6 Prefix Length (0~127) for this HTTP Device. |
| IPv6 Address | IPv6 Unicast address for this HTTP Device. |
| Gateway | Specifies gateway for the HTTP device. |
| DNS info via DHCP | Enables or disables DNS Information from DHCP. This option is set to Enabled by default. |
| Primary DNS | Specifies the primary DNS server IP address for the HTTP Device. |
| Secondary DNS | Specifies the secondary DNS server IP address for the HTTP Device. |
| URI (will obtain from DHCP server if not specified) | Obtain URI from the DHCP server if not specified |
| TLS Authentication Configuration | Specifies the option for TLS authentication configuration. |
NOTE:Autoconfiguration, Prefix Length and IPv6 Address options are visible only when
Protocol is set to
IPv6
| Option | Description |
|---|---|
| Connection 1 | Enables or disables the iSCSI connection. This option is set to Disabled by default. |
| Connection 2 | Enables or disables the iSCSI connection. This option is set to Disabled by default. |
| Connection 1 Settings | Enables you to control the configuration for the iSCSI connection. |
| Connection 2 Settings | Enables you to control the configuration for the iSCSI connection. |
| Connection Order | Enables you to control the order for which the iSCSI connections will be attempted. |
| Option | Description |
|---|---|
| TLS Authentication Mode | View or modify the device's boot TLS Authentication Mode. This option is set to One Way by default. None means the HTTP server and the client will not authenticate each other for this boot. |
| Root Certificate Configuration | Import, delete, or export the root certificate. |
| Option | Description |
|---|---|
| NVMe-oF SubSystem n (n = 1 to 4) | Enables or disables NVMe-oF SubSystem. This option is set to Disabled by default. |
| NVMe-oF SubSystem n Settings (n = 1 to 4) | Enables you to control the configuration of the NVMe-oF SubSystem, if Enabled. |
| Option | Description |
|---|---|
| Interface | NIC interface used for NVMe-oF connections. This option is set to Embedded NIC 1 Port 1 Partition 1 by default. |
| Transport Type | This field sets the value of transport type for NVMe-oF connection. This option is set to TCP by default. |
| Protocol | This field sets the value of protocol type for NVMe-oF connection. This option is set to IPv4 by default. When IPv6 is selected, IPv6 Autoconfiguration is used to get the IPv6 address. |
| VLAN | Enables or disables VLAN for this NVMe-oF connections. This option is set to Disabled by default. |
| VLAN Id | Specifies the VLAN Id for this NVMe-oF connection. This option is set to 1 by default. |
| VLAN Priority | Specifies the VLAN priority for this NVMe-oF connection. This option is set to 0 by default. |
| Retry Count | Specifies the retry count for this NVMe-oF connection. This option is set to 3 by default. |
| Timeout | Specifies the time out for this NVMe-oF connection. This option is set to 10000 by default. |
| DHCP | NVMe-oF connection gets subsystem's information from the DHCP server. This option is set to Disabled by default. |
| Host IP Address | Specifies the Host IP Address for this NVMe-oF connection. |
| Host Subnet Mask | Specifies the Host Subnet Mask for this NVMe-oF connection. |
| Host Gateway | Specifies the Host Gateway for this NVMe-oF connection. |
| NVMe-oF subsystem info via DHCP | Enables and disables the NVMe-oF subsystem's DHCP for this connection. This option is set to Disabled by default. |
| NVMe-oF subsystem NQN | Specifies the NVMe-oF subsystem's NQN for this connection. |
| NVMe-oF subsystem Address | Specifies the NVMe-oF subsystem's IP address for this connection. |
| NVMe-oF subsystem Port | Specifies the NVMe-oF subsystem's port for this connection. If subsystem NQN is empty, this field will be forced to the default Discovery Service port 8009.This option is set to 4420 by default. |
| NVMe-oF subsystem NID | Specifies the NamespaceID (NID) for this NVMe-oF connection. |
| NVMe-oF subsystem Controller ID | Specifies the NVMe-oF subsystem's Controller ID for this connection. This option is set to 0 by default. |
| Security | Enables or disables the security option for this NVMe-oF connection. This option is set to Disabled by default. |
| Authentication Type | Specifies the authentication type for this NVMe-oF connection. This option is set to None by default. |
| Securitykeypath | Specifies the Securitykeypath for this NVMe-oF connection. |
請給予評分 (1 到 5 顆星)。
請給予評分 (1 到 5 顆星)。
請給予評分 (1 到 5 顆星)。
本文章是否有幫助？請選擇。
評語中不得包含下列特殊字元：<>()\